Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 97-144 of 5477
$0 Price: $200.05

Buy Details

Availability: Out of Stock, On Order
Item #: 32345 -

Reproduction passenger side A/C vent with black camera case finish for the 67 - 68 Mustang. 

MSRP:$449.99
$449.99 Price: $399.85

Buy Details

Availability: In-Stock Item
Item #: 24322 -

Finally, an answer to the much needed, delicate 1968 air conditioning side vents! Visually, these are very hard to tell apart from the originals we have listed on this site but functionally they are much better in that they are cast in one piece. The originals were very prone to breaking and often when you close the door on your 1968 Mustang, Cougar or Shelby the lower portion of the vent falls off. This kit is correct for the 1968 Mercury Cougar only and it includes all three knobs and the...

$0 Price: $1.55

Buy Details

Availability: Out of Stock
Item #: 26652 -

This Accelerator Pedal Rod To Firewall Grommet reproduction fits both the 67 and the 68. Replaces Ford part # C6OZ-9793-A.

$0 Price: $9.77

Buy Details

Availability: Out of Stock
Item #: 16000 -

Reproduction diaphragm pump that mounts on the front all 67 - 73 Cougar or Mustang Autolite 2V carbs as well as 1967 Autolite 4V Carbs. With today's gas, these commonly fail, especially when sitting for extended periods of time. Complete failure will cause fuel leaks, but many times these will affect performance well before a leak actually starts. Good idea to replace every few years or if sitting for 6 months or more. Replaces Ford Part #: C4AZ-9B559-A.

$0 Price: $2.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 41376 -

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

$1.95 Price: $2.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0267 -

Ford called this small door latch part an adjuster. It threads onto the bottom of the door latch rod inside the door. Common to most Ford products 1965-1970. Ford part number C5AZ-62218106-A.

$0 Price: $181.55

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 25855 -

Fits perfect! The collar that slips into the opening of the bell housing is very tight for a precise fit that will withstand high horse power motors.

$0 Price: $21.64

Buy Details

Availability: In-Stock Item
Item #: 30956 -

Reproduction center cap adapter kit for installing Legendary center caps on the Legendary Series GT9 wheels. The spacing is a bit deeper on these specific wheels, so this adapter kit comes with special adapters and longer screws.  This kit is intended to make original and after market Mag 500 and Style Steel wheels center caps work on the Legendary Series GT9 wheels.  Please note that the included screws may not fit the thread pattern of some center caps.  The plates will...

$0 Price: $8.95

Buy Details

Availability: In-Stock Item
Item #: 14-0009 -

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the yellow colored adhesive, the factory used yellow adhesive on the weather stripping and is the 2 ounce size.

$0 Price: $15.56

Buy Details

Availability: In-Stock Item
Item #: 14-0010 -

New 5oz tube of yellow weatherstrip adhesive for installing the rubber weatherstripping found on the Mercury or Ford. This 3M brand adhesive is a great match to the yellow colored adhesive that Ford used to attach the weatherstripping on many of it's vehicles back in the day.

$0 Price: $45.45

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 31044 -

We will loan you this adhesive / epoxy applicator for 60 days, with a 100% refundable purchase price. Only available to customers that purchase our 3M bonding adhesive. Tool must be returned in undamaged condition with no missing parts within the 60 day time period.Returns past 60 days are subject to a 25% restocking fee. ...

$0 Price: $45.45

Buy Details

Availability: In-Stock Item
Item #: 14-0024 -

New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...

$0 Price: $69.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33153 -

Set of 8 fine threaded Phillips screw assemblies. This the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the...

$0 Price: $9.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 20024 -

This fine threaded Phillips screw assembly is the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The two new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the comparison...

$0 Price: $0.98

Buy Details

Availability: In-Stock Item
Item #: 30880 -

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

$59.99 Price: $61.85

Buy Details

Availability: In-Stock Item
Item #: 26202 -

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

$0 Price: $58.18

Buy Details

Availability: In-Stock Item
Item #: 41758 -

Economy Small Block Powering Steering Adjustment Bracket. Lighter weight material than OEM. Replaces Ford Part #: C7SZ-3A732-A.

$0 Price: $76.36

Buy Details

Availability: In-Stock Item
Item #: 13791 -

Perfect fit for your 289, 302, or 351w with or without AC but a hard sell when our good used rust free brackets cost less . . .

$0 Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24044 -

Used alternator adjusting bracket for any 1967-68 Mercury Cougar or 1967-68 Ford Mustang with 289 or 302 V-8 engines. C7OE-10145-A stamped bracket has a slightly rounded off end to prevent contact with some of the larger diameter water pump pulleys from previous years. Ford part number C7OE-10145-A.*Trivia - All 3 small block alternator adjusting brackets from 1965-1969 will fit most all 289 / 302 / 351W engines unless your engine has one of the larger pulleys. ...

$0 Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24331 -

Used alternator adjusting bracket for any 390 engine 1968-69 Mercury Cougar or Ford Mustang without factory smog. Specifically this is for 1968 390-2V or X code engines, and 1969 390-4V or 390IP engines offered in 1969 cars with S code designation. Replaces Ford part number C8AE-10145-A.This is the 411 for 1968-69 alternator mounting on Mustang and Cougar with 390 engines. If your 1968 S code car (390GT or 390-4V) was delivered in the United States (meaning not Canada or other foreign...

$0 Price: $28.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23937 -

Application is 1967 - 1968 289/302 and 1969 Boss 302 Eliminator alternator adjusting with factory air injection emissions. Casting number C6OE-10145-A, Ford part number C6OZ-10145-A.

$0 Price: $259.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24342 -

C8AE-9B452-B Thermactor smog pump belt tensioning adjustment bracket. Application is for all 1968 - 1970 FE engines with factory installed thermactor smog systems.

$0 Price: $250.00

Buy Details

Availability: In-Stock Item
Item #: 30885 -

Reproduction thermactor smog pump adjusting bracket for all 1968 Mercury Cougar and 1968 Ford Mustang with S code 390-4V engines. Additionally this bracket was also used on 1968-70 Mercury Cougar and Ford Mustang with 428 Cobra Jet engines. Quality made product. Ford number C8AE-9B452-B.

$0 Price: $79.96

Buy Details

Availability: Out of Stock, On Order
Item #: 10487 -

This high performance alignment kit replaces the factory eccentric bolt and cam that holds the lower control arm to the frame. The eccentric cam is used for setting wheel camber. When the eccentric is turned, the lower arm moves in or out changing camber. Stock eccentric cams can slip or rotate going over bumps, allowing the alignment to change. Which is the cause of many worn tires. The lower control arm adjusting cam eliminator kit replaces the eccentric bolt and cam with non slipping...

$0 Price: $29.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 30483 -

This knurled nut is located under the front slides in each corner (1 per side, 2 per car) and is used to adjust the height of the sun roof panel.

$0 Price: $69.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33152 -

Set of 8 1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples. Also sold individually.

$0 Price: $9.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19333 -

1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples.Also sold in a set of 8. ...

$0 Price: $2.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 20025 -

This bolt is what adjusts your headlamp cover height. Many people do not know they can rid themselves of that droopy eye look (misaligned grille) by placing new rubber pads on the heads of these bolts and adjusting them. Four required per car, sold individually. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

$0 Price: $19.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 30251 -

This bolt is what adjusts your headlamp cover height. Rare find to still have an original rubber bumper in place that is not compressed or cracked. Four required per car, sold individually. Check out this video

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24393 -

C8OA-3B236-A Complete lower control arm cam and attaching bolt. 4 pieces included - Cam/bolt, lower cam, nut and lock washer. We offer this used front suspension lower control arm adjusting cam from rust free Western States cars. These are MUCH better quality than any of the stock "looking" reproductions offered. For use on all 1967 - 1973 Mercury Cougar and Ford Mustangs. Part of the C6OZ-3048-A lower arm mounting kit. Bolt/cam part number C8OA-3B236-A, secondary cam part...

$0 Price: $125.35

Buy Details

Availability: In-Stock Item
Item #: 15704 -

This air cleaner assembly never came from the factory on any Cougar, but was an over the counter option available from your Ford dealer. If you have a very nice hood blanket I would think twice before using it in conjunction with this air cleaner assembly as it will leave an imprint. To avoid this problem with small block cars you can use a lower profile carburetor spacer, but on big block cars this is not an option due to the already thin design of the factory carburetor spacer. This will...

$0 Price: $172.45

Buy Details

Availability: In-Stock Item
Item #: 11975 -

Reproduction Group II customizable oval air cleaner with the optional "Walking Cat" for your Mercury Cougar. Good quality reproduction that will go nicely with our Cougar aluminum valve covers. The finish on the black portion is not the same as the crinkle finish on the valve covers but do know the crinkle finish can be added with an aerosol product found from most paint suppliers. If you are using a vented oil filler cap you will need to drill a hole in the base to insert the rubber...

$95.00 Price: $108.77

Buy Details

Availability: In-Stock Item
Item #: 26025 -

This 'Cal Custom' style 14" Air Cleaner Assembly looks great and really compliments our new matching oil pan and valve covers. These covers offer a true "old school" look. Clean look with no visible mounting nut. Lid has a 1/4x20 nut attached on the bottom side (requires shortening carburetor stud). Kit includes aluminum finned top, air filter, and bottom plate.

$0 Price: $45.86

Buy Details

Availability: In-Stock Item
Item #: 14897 -

This is the exact copy of the high performance air cleaner. This unit features a highly polished chrome top with a dimpled recess for the wing nut and all contours are concours correct. The filter element has the correct orange color and round hole design with the base plate painted in the correct Ford blue and also includes the breather tube. Decal and correct wing nut are optional.  Dimensions: 13 7/8" X 2 1/4" (edge height). Replaces Ford part # C5ZZ-9600. Check out this video ...

$0 Price: $755.80

Buy Details

Availability: In-Stock Item
Item #: 12136 -

Quality reproduction of the 1968 - 1970 CJ Mercury Cougar, 1969 - 1970 Shelby GT500, 1968 - 1969 Cyclone, Ford Fairlane, Ranchero and Torino 428 Cobra Jet Ram Air cleaner base. Features correct snorkel opening and breather elbow.Replaces Ford part number C9ZZ-9600-E or C8ZZ-9600-A.

$0 Price: $9.77

Buy Details

Availability: In-Stock Item
Item #: 14036 -

This screw / stud seems to always be missing. This screw is just a little longer than stock to accommodate installing the Hi-Po air cleaner. Fits most Autolite carburetors. Size: 4 1/8 inches length 1/4-20 X 5/16-18 threads. Check your thread size on the carburetor, we think that starting in 1969 the Autolite 4300 carburetors had 1/4-20 threads. Please note that this stud has 5/16-18 threads going into the carburetor.  Replaces Ford Part #: 370971-A *Note - Check your carburetor, it will...

$0 Price: $8.25

Buy Details

Availability: In-Stock Item
Item #: 26417 -

This is a reproduction of the original orange engine displacement decal with black lettering and black and orange checkerboard on each end that was located on the top of the air cleaner.Fits the following model with a 289 2 barrel engine:1968 Mercury CougarReplaces Ford part# C8DF-9C611-B

$0 Price: $8.25

Buy Details

Availability: In-Stock Item
Item #: 26340 -

This is a reproduction of the original engine displacement decal. Black on chrome background followed by black background with chrome head and lettering 390-2V located on the top of the air cleaner. Fits the following models with a with a 390 2 barrel engine:1968 Mercury Cougar X code 390 *CUSTOMER REVIEW* Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure...

$0 Price: $14.15

Buy Details

Availability: In-Stock Item
Item #: 12841 -

This is a reproduction of the original engine displacement decal. Black on chrome background followed by black background with chrome head and lettering 390-2V located on the top of the air cleaner.*CUSTOMER REVIEW* Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell...

$0 Price: $7.75

Buy Details

Availability: In-Stock Item
Item #: 26306 -

This is a reproduction of the original engine displacement decal with a chrome background with MERCURY in black lettering followed by the Mercury head logo and 390 4V in chrome with a black background. located on the top of the air cleaner.Fits the following models with a 390 4 barrel engine:1967 Mercury Cougar

$0 Price: $8.25

Buy Details

Availability: In-Stock Item
Item #: 26367 -

This is a reproduction of the original orange engine displacement decal with black lettering and black and white checkerboard on each end that was located on the top of the air cleaner.Fits the following models with the 390 4 barrel engine:1968 Cougar1968 Mustang

$0 Price: $7.75

Buy Details

Availability: In-Stock Item
Item #: 26438 -

This is a reproduction of the original orange engine displacement decal with black lettering and black and white checkerboard on each end that was located on the top of the air cleaner.Fits the following models with a 428 4 barrel Cobra Jet engine:1968 Cougar1968 Mustang Replaces Ford Part #: C8AF-9C611-D

$0 Price: $7.75

Buy Details

Availability: In-Stock Item
Item #: 26397 -

This is a reproduction of the original Autolite parts decal that was located on the air cleaner.Fits the following models:1968 Cougar1968 Mustang