1968 Mercury Cougar

Reproduction pillar post mouldings that feature and vinyl overlay for the Mercury Cougar or Ford Mustang. These units are sold as a pair.

Reproduction brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. These have 1/2 inch holes in them, like the originals.Replaces Ford part number C4UZ-2028-A.

Used pin for the cable that goes to the vacuum motor used in actuating the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Used only in the first part of 1968, later in the year this was upgraded to a clevis. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used pin for the locking lever in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Two are required in 1967-69, but only one is required for 1970 and up. Recommend changing to a up dated version of this pin with one that has circlips or snap rings (15-0156 for 1967 -69 or 15-0157 for 1970-1973) *NOTE* For tilt column service, you can contact Tony...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Locking pawl catch pin for your 67-69 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break...

Rear license plate and fuel door hinge pin for 1967-68 and 1971-73 Cougars and 1968-71 Ford Fairlane and Torino models, excluding station wagon and Ranchero. One pin for each side of the hinge, sold individually. Replaces Ford part # C6OZ-13432-A.

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

New pinion seal for any 8 inch third member found in 1967-73 Ford and Mercury cars. 1967-68 Mercury Cougar and all years of Mustang with 8 inch drop out rears.

Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.

Reproduction Exhaust Manifold Pipe Stud Kit for the 260, 289, 302, 351 and 1969 390GT 1967 - 1972 Mercury Cougar and Ford Mustang

Kit has the longer studs for use with spacers or butterfly spacers, between 390 and 428CJ passenger side exhaust manifolds and H pipe flange.

1967 - 1970 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C7ZZ-3590-B. Note that early 67's will have a 1" sector shaft. Having issues with wobbly or loose steering? Check out our video on sloppy steering below.

C7ZA-3590-B 1967 - 1968 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C7ZZ-3590-B.Having issues with wobbly or loose steering? Check out our video on sloppy steering below.

Power steering pitman arm for any 67-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts. Replaces Ford part number C9ZA-3590-A This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Power steering pitman arm for any 1967-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts. This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

C7ZA-3590-C 1967 - 1968 Power steering box pitman arm with 1-1/8" inch sector shaft. Ford part number C7ZZ-3590-C.Having issues with wobbly or loose steering? Check out our video on sloppy steering below.

Reproduction pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and 2 - 4 are required per car. Pin is custom made on short runs and is very difficult to find. .001 undersized, and with 8/32 threads instead of 6/32 like the originals. Newer pin removal tools will fit. Replaces Ford part # C7SZ-3D739-A. Removing pivot pins on 67 - 69 tilt away columns: Work on the upper knuckle pivot pins as there is room...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1076 WHITE Led Plasma back up light bulb for your 67-68 or 71-73 Cougar, Mustang or anything else you might have that takes an 1076 bulb. Please note that these bulbs are ground sensitive. Specs: Power: 7.5 Watts Brightness: 300 Lumens Total life expectancy: 30,000 hours 2" Tall (1 3/8" extends out of the socket) Comparison image - Click to view full-size: ...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 back up light bulb for your 69-70 Cougar or Mustang. (67-68 and 71-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175) These Plasma LED bulbs will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Plasma LED 1157 replacement bulb in YELLOW for your parking / running lights. Much brighter than stock, more responsive, and less power draw. We won't go so far as to call these little guys AMBER, but they're definitely yellow. Good for your 67 - 73 Cougar, Mustang or anything else that takes a dual-filament 1157 bulb for marker lights or turn signals. Specs: Power: 7.5...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1157 WHITE LED Plasma stop lamp / turn signal light bulb for your 67 - 73 Cougar, Mustang or anything else you might have that takes a white 1157 bulb. Please note that these bulbs are ground sensitive. Did you know that white (clear) 1157 bulbs fit a ton of other cars and trailers from the 50's clear through the 90's and beyond that used the...

24" hose with metal coil (like original) instead of plastic coil found in most. Coils are wrapped in a 6+ mil plastic rather than the 3 mil plastic that you can easily put your thumb through. Does not come with clips. May require being cut to fit some applications. 2 required per car. Replaces Ford Part #: B5A-18556-C.Replaces Ford Part #: B5A-18556-C.

This face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are going to be missing that piece, because after all......that dampener has been in there for up to 46 years! (this doesn't effect its useability). You can use your existing...

When placing your order, be sure to leave a note as to which color you're looking for and we'll do our best to find them for you. Limited quantities available. This colored face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are...

These reproduction face plates fit inside the buckle bezel on the two piece type seat belt buckle cover. Sold as a pair. You can use your existing spacer, or if you're missing one, you can find it here. Check out our video "All about seat belts" below. ...

This is the complete one piece seat belt buckle cover which comes with the face plate (with the round cutout for the push button) and the bezel all in one. This version is handy when you don't want to deal with multiple parts (as is the case with the separate face plate and bezel version). Simply remove your old cracked or broken cover, replace the metal spacer, and pop this cover into place and you're ready to go! You can use your existing spacer, or if you're missing one, you can find it...

Shrink-on plastic sleeve that is found on the lower part of the collapsible steering columns. Used sleeves are often ripped and torn. Simply cut off your old sleeve and install this item to give your column a newer look and feel. Installation: Make sure that your column is clean. Lube the column and inside of the sleeve. Do not remove the crease on the plastic, you need it to help you put the sleeve on the tube. Push the sleeve on as far as you can. Gently tap the sleeve down on a table top...

Used cover plate or thrust plate that retains the camshaft on the front of Ford small block V-8 engines such as 289, 302, 351W. 1967-70 Mercury Cougar or Ford anything. This plate has three bumps, we have found a Ford number of C9OZ-6269-A, this may be a service replacement number and could be found on engines built earlier than 1969. We have found this style of 289's from 1967. There is another version with Ford number C2OZ-6269-A, it only has two bumps.

Used cover plate or thrust plate that retains the camshaft on the front of Ford FE big block V-8 engines such as 352, 360, 390, 410, 427, 428, and 428CJ. 1963-70 Mercury Cougar or Ford anything. We have found a Ford number of C3AZ-6269-A, 

Reproduction plastic plate that goes between the dash bezel and dash pad on any 1967-68 Standard model Mercury Cougar with factory air conditioning. This is for the center vent and is has a Ford casting number of C7WB-65044E88.Note: The lip of the plate points downward. The plate slides in behind the dash face pad, see above photo for reference.

Used plastic plated plate that goes between the dash bezel and dash pad on any 1967-68 Standard model Mercury Cougar with factory air conditioning. This is for the center vent and is has a Ford casting number of C7WB-65044E88. These originally were chrome vacuum plated, like the dash. These will have some degradation or flaking chrome. No breaks or cracks on the plastic.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side lower only, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502639-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side upper only, kind of shaped like the State of Arizona, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502667-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side lower only, marked with an "R". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502638-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side upper only, kind of shaped like the State of Arizona, marked with an "R". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502666-A.

Floor tunnel body reinforcing plate for the floor shifter on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than other years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number C5ZZ-6512118-A.

Brass screw in plug for select Autolite distributor vacuum advance units from 1968-71, typically the banded single advance units factory installed. Solid brass, originals were not, we believe that they were cadmium plated. Solid plug, should be hollow, with a 3/4 inch hex head. Works as it should. Fits most all vacuum advance that have a plug in the end as shown. *Note, when removing the old plug, there is a spring and washer inside. 

These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up. Plug size: 1 1/2"   also used for the electric headlight conversion kit for the firewall pass through body plug.  

Used voltage regulator plug for the 67 - 68 Mercury Cougar. Plug end only, does not include any wiring.

Used taillight wiring harness repair plug and pigtail to the driver side (left hand) center taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used taillight wiring harness repair plug and pigtail to the driver side (left hand) inboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...