1968 Mercury Cougar

Used intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This mounts at the top front corner of the driver side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B.You may also need the attaching screw. Replaces Ford part number C7WY-6531491-B or C7WB-6531491. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

This mounts at the top front corner of the passenger side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B.You may also need the attaching screw. Replaces Ford part number C7WY-6531490-B or C7WB-6531490. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

Factory knob for the new for 1968 rear window defogger. This is the knob for the 2 speed fan switch mounted to the bottom dash on cars so equipped. Rare option, we try and match these up to the switches. Spares occasionally come in, subject to availability.

Used emergency flasher knob for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is a very fragile part which we never find in good used condition. What you will see when it has been broken off is an exposed Phillips screw head. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes...

Hard to find knob with no crack or peeling issues, correct for right or left side Torino, Cougar, Mustang. Not for use with console equipped Mustang and Cougar. Casting number is C8OA-18A932-B.

Used on the Mercury Cougar or Ford Mustang with a factory center console and measures 1-3/8 inches tall. Replaces part # C8ZA-8A932-B

This is correct for your 1968 non console Mustang or Cougar. Fits left or right, no cracks or peeling. Casting number is C8ZA-18817-E.

Used on Mercury Cougar or Ford Mustang with a factory center console. Replaces part # C8ZA-18817Fits:1968 Mercury Cougar

This set of knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and...

Good used set of four knobs for your Mercury Cougar or Ford Mustang with a factory center console. These are plastic and much deeper than the non-console version. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 1968-70 AM radios with rear speakers and 1968-70 AM-FM radios, if you need the white spacer we offer it here. Our blow-out price is based on the fact that these are now available new! Knob length 1 1/2"Sleeve length 1 5/16" ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang.  There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

This is the factory Ford remote trunk latch as used on luxury cars such as Thunderbird or Lincoln. As you can see from the photo, they are made (and install) exactly like our Cougar trunk latches, but with the addition of a release tab. These can be installed to use either a cable, vacuum, or solenoid release.

The 1967 Cougar was Mercury's attempt to enter the Pony Car market segment popularized by the April 1964 introduction of Ford's Mustang. Introduced in the fall of 1966 for the 1967 model year, the first-year 1967 Cougar exceeded all sales expectations with 150,893 units sold. It was selected as Motor Trend's 1967 Car of the Year. Legendary Cougar Magazine is dedicated to the first three generations of Mercury's luxury Pony Car. Each bi-monthly issue includes features on the first-generation...

Used high beam indicator lens for the 68 XR7 Cougar.

Used grade "B" rear courtesy / opera light lens for the Mercury Cougar. Opera lights were came as standard equipment on all XR7 Cougars, but were installed on many decor and standard level Cougar interiors. These units will have a few "warts" which show up as pitting in the chrome and may also have some minor cracking in the lens. If you just need a lens for your driver quality car, these are a great option. But if you compare this grade "B" lens to our reproductions, it will look like...

Used Carter fuel pump lever. From Carter made fuel pump as installed on Ford 352, 390, 410, 427, 428CJ FE engines. Many of the Carter "X" fuel pumps with screw together rebuildable pumps often times have Ford small block levers. Housings are he same. Levers are removable, see youtube for the rebuilding and assembly procedure.

These plates show almost no wear and would look right at home on a show car.NOTE: The plates and plate numbers pictured are exactly what you'll receive.

These plates show average wear and can be used as is, or restored to look new.NOTE: The plates and plate numbers pictured are exactly what you'll receive. 

Reproduction license plate frame for your Mercury Cougar.  Sold individually. Note: These will not clear on the rear pull down fuel door on the 1967- 1968, so they will only work for the front license plate on the 67-68 Cougar. These can be used for front or back on the 69-73 Cougar.Check out this video of our 2013 Open House event. Se you next year! ...

Pair of reproduction license plate frames bearing the name of the the original Lincoln / Mercury dealer lot in San Jose, California.  Chrome with the city and dealer name written in/on reflective material. Sold only as a pair.

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair could use a bit of restoring to get back to perfect condition, but they are in good shape and will not have any extra holes like the grade B plates do.   NOTE:  "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair has extra holes drilled, which would need to be repaired (see pictures). They could be restored or used as-is. Because of this, we're selling them at a reduced price. NOTE: "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

Rechromed GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine, that did not come with the GT package, would have used the painted air cleaner lid. Replaces Ford part # C7OZ-9661-A.*NOTE* The outside dimension of the lid is 16.75 inches and will not fit the...

This used assembly includes lamp socket, bracket, mercury switch, and length of wire.Replaces part # C7ZB-15702-A

NOS Lincoln Mercury accessories booklet for the 1968 Cougar, Montego, Continental and other models in the same year. Filled with options including mirrors, radios, luggage racks, fire extinguishers, speed control and more.  Volume 68 PSM 139B

Used Link for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Link is a tubular shaft for the Rod. It attaches to the Trunnion. Ford part number C7ZZ-9D768-A.

This is for the person who is missing it all. Includes all you need as seen in the picture and includes the reproduction chrome cover on a good used housing. Let us know in the comments whether you prefer a Standard or XR7 decal installed on the flip up door. Check out our video below showing how to easily remove and re-install your 67-68 trunk latch, lock, and cover plate and some info on getting a new key made. This icon means that we're looking to buy this part!WCCC is a buyer of used and...

Good used cylinder as taken from a 1967 - 1968 trunk lock housing. Will have minor damage but cosmetic only, 100% functional. Ford Part # C7SZ-6543505-A or C7SZ-6543507-B (Glove box/Trunk lock kit) Check out this video Below are some basics about removing and replacing your lock cylinder and lock cover. When removing the cylinder from the lock housing this button must be depressed to allow the cylinder to slide out the front of the housing.  The only way to depress the button is to...

This matched set is actually for a 1968 model Cougar but works just as well on a 67. The only difference being 1967 had squared off edges on the glove box button and 1968 had rounded edges which are safer in a collision.Ford Part # C7SZ-6543505-A/C6OZ-6206281-C or C7SZ-6543507-B (Glove box/Trunk lock kit)

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1967-69. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Includes two door lock cylinders, two Ford keys, and one ignition lock cylinder. Assembled from the best used locks. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

This is a good used, grade A deck lock housing with nothing included except the studs. There will be no major blemishes or pitting and the cover stop in the bottom corner is intact. This is an impossible part to have restored and look OEM so finding a really good used one is important for a high quality restoration. Check out this video

This is a decent used, grade B deck lock housing with nothing included except the studs. There will be a couple of blemishes that may include minor pitting but the cover stop in the bottom corner is intact. Perfect for a driver as very little of the chrome shows when this is installed, our reproduction cover will cover almost all of this part in the down position. Check out this video

This deck lock housing has been carefully stripped, polished and triple plated. You can send yours in in advance as an exchange or pay the core charge and return your old one later. Do know once a multi-faceted part like this has been stripped, polished and replated, some of the crisp, sharp detail will be muted and it will never again look just like factory. If you have extra cores we are buyers, especially if your lock assembly is complete. Check out this video ...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory J code 302-4V V-8 engine. Rated at 230 Hp with 10.0:1 compression ratio in 1968. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and oil pan are included...

Used only in 1968 Manual 3spd and 4spd on non xr7 models and Mustang. Very hard to come by with no splits, burns or cracks. We rarely can supply the color you desire but please let us know your desired color and we will try. Grade A will not have UV ray damage and will look right at home in a low mile car. Satisfaction guaranteed.

Rare find, must have for your Concours Cougar. Sold individually.Ford part number C5ZZ-1012-BFits the following models with Styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang

Reproduction GOLD HAZE lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Not 100% concours correct but close close in design to the 1968 - 1973 handle. Works well for 1967 as well. Replaces Ford Part Numbers: C5ZZ-17032-A, C5ZZ-17032-B ,C8ZZ-17032-A, D0ZZ-17032-A, D4ZZ-17032-A.Customer feedback from mercurycougar.net: Don and WCCC were always one of the service quality benchmarks for my business. Despite the many pressures faced by any small business owner, Don always treated me and my car as if we were his only customer. And, he NEVER let me down - parts...

Optional trunk lamp. Includes mercury switch that mounts on inside trunk lip, round plastic wire protector bezel, mounting screw and wiring pigtail. Ready to install working part, #631 bulbs available. Guaranteed to work, no cuts or splices.Can be added to any 1967 - 1968 Cougar and may be able to be added to the 67 - 68 Mustangs, but some Mustang forums indicate the Mustang lamp had a different wire length than the Cougar lamp and this version is stamped with the correct part number for the...

Nice used original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds with hardware. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on center. This rack was utilized for may years on many cars. The same company made them for...

RAN-D or RAN-D1 Original equipment 3 speed top loader 3.03 transmission from a 1967 - 1968 Mercury Cougar with engine code C - 289-2V, or engine code A - 289-4V only. Could also have a casting number of RAN-D1. Ford master part number C5ZZ-7003-V.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each...

RAT-U Original equipment 3 speed top loader 3.03 transmission from a 1968 Mercury Cougar with engine code F - 302-2V, or engine code J - 302-4V only. Ford master part number C5ZZ-7003-Z.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X = 46.8%W = 33.6%U = 9.5%1 = 7.2%5 = 2.5%6 = 0.5% ...

RAT-N1 or RAT-N2 Original equipment 3 speed top loader 3.03 transmission from a 1968 Mercury Cougar with engine code S - 390-4V only. Transmission with casting number RAT-N2 also used during this model year. Ford master part number C8ZR-7003-E. *Note - RAT-N could also be sustituted.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame...

C5ZZ-7400-C3Assembly Factory 3 Speed manual transmission shift control assembly for any 1967 - 1968 Mercury Cougar and 1965 - 1968 Ford Mustang, 1968's only up until 1-2-1968. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The 1-2-1968 date was the transition of the stronger trunion for the shifter mounting. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 390-4V engine. Check out our...

RUG-E2 Original equipment 4 speed top loader transmission from a 1968 Mercury Cougar with engine code C - 289-2V, engine code F 302-2V, and engine code J 302-4V only. Ford master part number C6ZZ-7003-E. Bare transmission. Percentages of Cougars equipped with a manual transmission by year 1967 = 18.5% 1968 = 13.2% 1969 = 10.5% 1970 = 7.8% 1971 = 2.8% 1972 = 1.5% 1973 = 0.7% Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%) Percentage of each transmission; X = 46.8% W...

RUG-AE or RUG-AE1 Original equipment 4 speed top loader transmission from a 1968 Mercury Cougar with engine code R 428 Cobra Jet only. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear. Ford master part number C8ZZ-7003-B.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame...