1968 Mercury Cougar

Nuts and bolts, associated with the installation of our used 1968-69 strut rods. 1 large and medium nut for the front, and two bolts and nuts to attach to the lower control arm.

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

Stud for attaching heat shield to passenger side exhaust manifold. Fits all 1968 Mercury Cougar or Ford Mustang and other Ford too. Sold individually. Phosphate & Oil (gray-black)

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 

Reproduction 15x7 chrome styled steel wheel for your Cougar or Mustang. Technically correct for Mustang because of the holes being placed in the center of the arms instead of in the inserts like the Cougar, but will fit both vehicles. Gorgeous reproduction of the original 1968 Mustang styled steel wheel. Correct in every way except that the outer band is welded on instead of riveted to the center section. This wheel has a total width of 7", backspacing is 4" and the center hole is...

Reproduction chrome center cap with blue background and chrome Mercury man logo for the Mercury Cougar. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the...

Reproduction chrome center cap with red background and chrome Mercury man logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from...

Reproduction chrome center cap with red background and chrome walking cat logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good...

Pair of reproduction sub frame connectors, designed to tuck up against the floor pan as tightly as possible to maximize ground clearance. The more performance improvements you do to the vehicle, the more demands are put on the uni-body. Sub frame connectors provide resistance to chassis flex, therefore increasing the integrity and rigidity of the chassis. Installing them will also help reduce rattles and squeaks from the car flexing over rough roads.They are a must for any performance...

This is the 1968 Cougar visor bracket. Not an exact match for 1971 - 1973, but will work. The hole spacing and distance from the windshield is identical to that on the 71-73, the bracket is just 1/8" longer on the side that actually holds the visor tip. This unit is only available in black or neutral. We have most other unfaded colors in used. This item works for 68 Cougar Coupe, 68 Mustang Coupe / Convertible and 71-73 Cougar Convertibles. Replaces Ford Part # C8ZZ-6204132, C8ZZ-17690 OR...

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

For the purists out there we have a very limited amount of used moon crater visors that have no impressions, seam separation and minimal rust on the clips if any.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually.

Reproduction Moon Crater Sun Visor for the 1967 and 1968 Mercury Cougar / Ford Mustang. Visors are fully padded and covered with the correct textured moon skin to match the headliner. Sold as a Pair. Nugget Gold is not available in Moon Skin Crater, it is only available in a smooth vinyl.

This decal was sometimes placed on the dash face pad near the middle or right side, and sometimes on the sun visor.

This 4 1/2" long flexible drive cable connects the Bosch "sardine can" motor to the gear box drive assembly. Limited supply. Check out this vintage XR7G television commercial ...

Used 1968 Mercury Cougar sunroof motor access panel. This panel is covered by the headliner, but can be dropped down (headliner is glued to the panel) to access the sunroof motor. Will always have a multiple, repairable cracks, but is still functional.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Used support bracket for the hood latch on any 1967-68 Mercury Cougar. L shaped support bracket goes on top of the hood latch assembly. It also attaches to the radiator core support.Ford part number C7WY-16707-A.

Used strap or support bracket for the foam air conditioning vent tube going to the driver side A/C vent. The electrical assembly manual indicates that this strap bracket behind the dash on the driver side. Our findings from the wrecking yard show that 1967 is typically rubber coated, 1968 is bare steel. Please specify is you have a preference. The rubber coated ones will show some deterioration, plan on re-dipping or use as-is. Not exactly the same as the support for the passenger side.Ford...

Reproduction brake pedal hanger for manual brakes. Can be modified to work for power brakes.

This used brake pedal support bracket is the correct hanger for a 1967-68 Mercury Cougar or Ford Mustang with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint, unused condition. Ford part # C7ZZ-6501508-C. *NOTE* Manual brake supports are different. Manual brake supports have four threaded...

This used brake pedal support bracket or brake pedal hanger is for the Mercury Cougar or Ford Mustang equipped with power disc or drum brakes. We have carefully shown the mounting position of the pedal so you can drill your existing manual brake pedal hanger when converting from manual to power brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means...

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design. Two different sized brackets used, this is the larger one that is 1-3/4 inches wide. The bracket that goes in the corner above the switch panel is 3/32" less. It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend...

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the smaller design. Two different sized brackets used, this is the smaller one that is 1-21/32 inches wide. This bracket goes in the corner above the switch panel. The larger bracket is 1-3/4" or 3/32" wider. It was obvious what the original intent was on this design in that a tab on the L...

This often times missing bracket was attached to the back of your early 1967 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the less common design.It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend into the rectangular hole to keep the bracket properly anchored to the fragile plastic. For some reason the majority of the cars built didn't get the better...

Reproduction set of 5 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design of the two and by far the superior. Replaces item # 31908Through 67-68, there were four different style brackets, you can see all four by following this link.Check out our dash bezel repair video: ...

This often times missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design.Through 67-68, there were four different style brackets, you can see all four by following this link. ...

Reproduction set of 5 XR7 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. Our improved design is better than the original in that the tab extends into the rectangular recess in the dash bezel which anchors in MUCH more securely.  Replaces item # 31907 Through 67-68, there were four different style brackets, you can see all four...

Radio support bracket for 1967-68 Mercury Cougar and Ford Mustangs without consoles. Used on AM, AM/FM, and AM/8Track factory radios.Replaces parts #s C7ZA-18888-A & C8ZA-18888-A, as found in the electrical assembly manuals.

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

This is the right hand or passenger side spring that holds the rear license plate or fuel door in the upright position. Fits 1967-68 and 1971-73 Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-A

Here is our free 7MB download for the 1967 - 1972 Mercury Cougar suspension diagram.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.  

C7ZZ-5482-C This is a factory used sway bar for the Special Handling Package as found on with the 1967 and 1968 GT option. This bar was factory identified with a single 'Green' paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.

Used front sway bar, does not include any mounting brackets or end link kits. Ford part # C7WY-5482-A.

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm. 8.0 oz., pre-shrunk 50/50 cotton/polyester1x1 athletic rib with spandexBrass zipper and dark grey trimSelf fabric lined collarSatin labelDouble needle stitching at waistband and cuffsQuarter-turned ...

Plunger switch that mounts to the air distribution manifold behind the center A/C vent. A mechanical lever operates the switch when the air damper is in the proper location to distribute air through the center air conditioning vent of the dash. This switch controls the clutch on the A/C compressor. 1967-68 Mercury Cougar and 1966-67 B Body Ford, Fairlane, Ranchero, and C Body Mercury Comet and other variations Cyclone etc. Tested and working switch. On Cougar and Mustang it attaches to the...

Used air conditioning thermostat switch for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Ranco for Ford. Ford part numbers C7ZA-19618-C or C7ZZ-19618-A.

C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573.*Note - 3 speed switches are different than the 4 speed switches.

Reproduction backup lamp switch that mounts to the factory 4 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-561. Replaces Ford part number C7ZZ-15520-A.*Note - 4 speed switches are different than the 3 speed switches.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.