1969 Mercury Cougar

These same clips are also found on the four rocker switches located in the center of the 1969-1970 XR7 dash pad. Do not bend the "J" shaped tab any further than is necessary to release the plug from the back of the switch as these break easily. There are 16 of these used on a Cougar with power windows in 1969, add the 8 in the dash of the XR7 Cougars and some cars have a total of 24.Replaces Ford part number C9AZ-14530.

These same clips are also found on the four rocker switches located in the center of the 1969-1970 XR7 dash pad. Do not bend the "J" shaped tab any further than is necessary to release the plug from the back of the switch as these break easily. There are 16 of these used on a Cougar with power windows in 1969, add the 8 in the dash of the XR7 Cougars and some cars have a total of 24.Replaces Ford part number C9AZ-14530.

Non-original style replacement clip for mounting the quarter window regulator arm to the window channel bracket on all 1969-70 Cougar and Mustang coupe and convertibles. This clip will work with either the 1969-early 1970 bracket and the late 1970 bracket. The late 1970 brackets used a unique spring steel clip that seldom is reusable. Sold individually, one each per window.

Partially dipped clip for attaching the seal on top of the radiator core supports. Often times with air conditioning the seals were installed. The factory sometimes used staples, sometimes clips. You would have to investigate your core support for staple holes. 5 clips are typical for attaching the seal. Spread them apart to where it looks equal. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. ...

This is the speedometer cable clip that connects to the firewall and transmission tunnel. Replaces Ford Part # : 373829

Six required per car.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject.

New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually.  Replaces Ford part number 382929-S.

Used Trunk Light Wire Plastic Clip for the 1967 - 1973 Mercury Cougar

Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.

These original hood blanket clips grip much better than the reproductions. Usually there were 10-11 of these clips used but it can vary from car to car as they tended to be inconsistent at the factory on how many of the available holes they actually stuck a clip into. Sold Individually.

Replaces Ford Part # : C9ZZ-6503406Sold Individually.

C9ZZ-6503406-A Front windshield lower moulding retainer clips. 7 clips required per car, sold individually.

Windshield washer hose clip that holds the hose up under the cowl. Concours quality

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

Used plastic clip for the Mercury Cougar or Ford Mustang.

New reproduction wire loom clip for the lower radiator core support.

Found on the lower radiator core support.  4 clips needed to attach the wiring harness and the vacuum hoses for the headlight system. Sold Individually. Replaces Ford part # 383104-S.

Found on the lower radiator core support. 4 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part # 383104-S.

Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S

Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.

Vinyl dipped. Clip is used to hold wiring away from hot engine. Also found on trunk floor.

Sold as a set of twelve (two more than required), replaces Ford part #C9WY-6510182-A. From the factory there were five of these on each side for a total of ten per car. These same clips were also used on 1977-1979 Mercury Cougars and Thunderbirds. Most likely they were used on other FoMoCo products.Fits: 1969 Mercury Cougar1970 Mercury Cougar

Reproduction black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.

Reproduction black plastic clip that goes onto the lower center of the firewall of any 1969 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is only found on 1969 and 1970 cars.

Used black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.

Used black plastic clip that goes onto the lower center of the firewall of any 1969 Cougar or Mustang. Also found on the back of the instrument cluster on the 71 - 73. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is...

Clips or clamps for attaching the 3/8" hard fuel lines to the body of any 1968-73 Mercury Cougar or Ford Mustang. Clips only, save your attaching body bolts. Sold in packages of 4 clips as shown. Will work on 1967 cars if you change to 3/8 lines. 1971-73 Cougar owners can use item 27565 attaching bolts, they are the same as the fuel tank mounting bolts. See related items. Replaces Ford 354663-S8

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

This is the sub-kit you would have received when you purchased a stainless steel service replacement deck moulding for your 1967 - 1970 Mercury Cougar. The original clips used with a 1967 - 1968 aluminum deck lid moulding would have been similar but would have had a plastic shell surounding the metal clip. For more insight on this tricky trunk trim, check out our video below: ...

Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.

Used standard core clock for the Mercury Cougar. These standard clocks generally do not work after 40 years and are considered cores. We also offer clocks with modern quartz movements or NOS movements in restored clocks. Check out the video below on our new gauge tester: ...

This clock has had the original mechanical movement replaced with a modern, new quartz movement. You should get many years of trouble free accurate use out of this clock. The factory equipped movements were very unreliable and often quit after a couple years use. We now put a new lens in every rebuilt 1969-70 XR7 / Eliminator clock we sell. Not only has the movement and lens been changed but every part of this clock inside and out has been given attention. We have used several clock restorers...

This is a Rebuilding Service - 1969-70 standard core clocks must be received by WCCC prior to shipment. Please call 503-463-1130 if you do not have a core clock. Core clocks for this service are available. C9WY-15000-A 1969 – 1970 Standard Cougar body code 65A, 65C, and 76A, found optionally in the drivers side instrument cluster. This clock was installed on Cougars with decor and standard level interiors and was located within the instrument cluster on the driver side. It has had the original...

C9ZB-15A006-B Wiring harness, or pigtail that goes from the back of the clock to the main under dash wiring harness. This wiring harness includes the 2 light sockets for the clock illumination. Ford master part number C9ZZ-15A006-A. Fits XR7 and standard Cougars. Fits 1969 Mustang.

Good used knob, threads off counter clock wise from the shaft. This item will work for both Standard and XR7 models.

C9WY-15017-A Steel bracket that fastens to the rear of the passenger side dash for mounting the clock. We offer this bracket because it often comes up missing when a dash pad from a standard Cougar is transplanted to an XR7.

Used in conjunction with Ford fan part # C9ZZ-8600-C that is stamped C9ZE-E. Features a parkerized shaft with an integral mounting flange. The aluminum portions are finished with silver cadmium and are mated together with filister head, Phillips machine screws (8) and an additional crimping operation was used to assemble the front and rear housings. The radial curved spring was originally finished in gold cadmium. This assembly stands 2 5/8" tall when set on its front surface, and the distance...

Reproduction thermal fan clutch that fits 1967 - 68 289 engines, 1968 302/390/427/428CJ engines, and 1969 351W engines, all with original Ford thermal cooling fans. Slightly larger in overall diameter, (still fits fine), and retains the correct spacing from radiator. We know that these will fit Mercury Cougar and Ford Mustangs 1967-69. Closest reproduction fan clutch on the market that fits the original and reproduction C8OE-B 7 blade power fan. Hayden fan clutch with an overall height of 2.98...

For all 1969 351 engines with either extra cooling or air conditioning.  Good working used unit, however we are unable to warranty these units. Ford part number: C6OZ-8A616-E (YB-104).  Engineering number: C9WE-8A616-A Marked C9WE-A on the hub.

Heavy Duty reproduction fan clutch that fits the original and reproduction C9ZE-E 7 blade power fan. Hayden fan clutch with an overall height of 2.707 inches. About 5/32" taller than our standard duty fan clutch. Please make sure that you have the clearance behind your radiator.  Similar design as originals, with thermal activated clutch. Overall diameter is 7.25 inches. The C9ZE-E 7 blade clutch fans were installed on 1969-70 Mercury Cougar and Ford Mustangs as well as 1969 Torino,...

Used in conjunction with Ford fan part # C9ZZ-8600-C that is stamped C9ZE-E. Features a parkerized shaft with an integral mounting flange. The aluminum portions are finished with silver cadmium and are mated together with filister head, Phillips machine screws (8) and an additional crimping operation was used to assemble the front and rear housings. The radial curved spring was originally finished in gold cadmium. This assembly stands 2 5/8" tall when set on its front surface, and the distance...

Economy version of the clutch adjusting rod that fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.

Reproduction premium adjusting rod which includes: 2 Lock Nuts 1 Spacer 1 Retaining Clip Fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.

Core used set of Eaton clutch brushes, we save these because of the FoMoCo stamped bracket with Ford part number C7AA-2979-A. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to reproduction version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for NEW Eaton brushes. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

This set of brushes only fits the Eaton brand of air compressor clutch. These are exact reproductions made from the original tooling. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to this version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for core brushes with stamped Ford numbers. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

Nice reproduction of the original. Replacement Z-Bar for 1969 and 1970 351W engines with either 3 speed or 4 speed manual transmissions. Replaces Ford # C9ZZ-7528-A.

Nice reproduction of the original. Street name is Z-Bar. For all 1967 - 1970 FE engines 390 and 428CJ. Replaces Ford part #: C7ZZ-7528-B.