1969 Mercury Cougar

Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

3 Speed manual transmission shift control assembly for any 1969 Cougar or Mustang. Control assembly only, no rods or chrome lever. C9OZ-7400-B Check out our video on rebuilding your shifter below: ...

C9OZ-7400-B3Assembly Factory 3 Speed manual transmission shift control assembly for any 1969 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 390-4V engine. Check out our video on rebuilding your shifter below: ...

C9OZ-7400-AAssembly 4 Speed manual transmission shift control assembly for any 1969 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on all V8 Mustangs and Cougars. Check out our video on rebuilding your shifter below: ...

Used automatic shifter bezel / indicator assembly for all Mercury Cougar and Ford Mustang with or without consoles. These are the best used ones from our inventory. These will have some minor issues with the chrome plating and most often need some detailing on the black pebble grain. Consider also purchasing a new seal, shift indicator lenses may or may not meet your requiements. Doesn't meet your requirements? We have very nice quality 1969-70 reproduction shift plate bezels also available....

Leather manual shift boot for the Classic Console Cruiser Console that we offer. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

C9ZZ-7210-A Shift lever for all 1969 Mercury Cougar and Ford Mustangs. Manual 3 speed only, 4 speeds are different. *Note - Must be used with Trunion C9OZ-7210-B, sold separately. Check out our video on rebuilding your shifter below: ...

C9ZZ-7210-B 4 Speed shifter lever for any 1969 Mercury Cougar and Ford Mustang with V-8 engines. *Note - Must be used with Trunion C9AZ-7210-J, sold separately. Check out our video on rebuilding your shifter below: ...

Used 4 speed manual transmission shift control assembly for the Mercury Cougar or Ford Mustang.Ford part # C9OZ-7400-A. Check out our video on rebuilding your shifter below: ...

Adapter plate for mounting the 3 or 4 speed shifter control assembly to the Top Loader transmission.Ford part # C9ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the "Select-Shift" automatic transmission. FMX transmissions only, code "X" on your door data plate tag. All 351 engines received the FMX automatic transmission. Rod with casting number C9OA-7340-A. Shift rod approximately 17-1/2 inches long. Ford part number C9OZ-7326-A. 1969 only. Check out our video on rebuilding your shifter below: ...

C9OZ-7210-B "U" shaped bracket that attaches the 3 speed shift lever to the shifter control assembly. For use on all 1969 Mercury Cougar and Ford Mustangs with the 3 speed shift lever. Bottom bracket only, called a Trunion (see illustration). *Note - Must be used with 3 speed shift lever C9ZZ-7210-A. Check out our video on rebuilding your shifter below: ...

C9AZ-7210-J "U" shaped bracket that attaches the 4 speed shift lever to the shifter control assembly. For use on all 1969 Mercury Cougar and Ford Mustangs with the 4 speed shift lever. Bottom bracket only, called a Trunion (see illustration). *Note - Must be used with 4 speed shift lever C9ZZ-7210-B.

These shocks are the as close to original specs as possible for the Mercury Cougar. This is the performance shock for those looking for firmer ride. The KYB Gas-a-Just shocks use higher gas pressure to keep your tires glued to the road. The KYB Gas-a-Just shocks' velocity-sensitive valving system adjusts quickly to changing road conditions for maximum comfort in any situation. Their mono tube configuration eliminates aeration and foaming, their micro-smooth, hard-chromed pistons extend their...

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

Good working grade "A" driver side (left hand) mirror that will look as good as the one shown here. Since the wand is recessed into the door panel on the 1969 Cougar, the wand is not prone to breaking off like the 1970 version which protrudes straight out. NOTE - Cable length should be 18" from the base of the mirror to the inner end of the remote wand assembly. In order to keep the cable from hitting the window, there's usually a clip to hold it away from the glass. This clip is hard to come...

Good working grade "B" driver side (left hand) mirror that most likely will not have as good of chrome as the one shown here. Since the wand is recessed into the door panel on the 1969 Cougar the wand is not prone to breaking off like the 1970 version which protrudes straight out. NOTE - Cable length should be 18" from the base of the mirror to the inner end of the remote wand assembly. In order to keep the cable from hitting the window, there's usually a clip to hold it away from the...

Used driver side (left hand) grade "A" manual side mirror for the Mercury Cougar. This is your plain Jane manual adjust mirror for the driver side of your 1969 or 1970. Uses same base mounting pad as all 1969-70 Cougar driver side mirrors.Ford part # C9WY-17696-B. Do you have riv-nut questions? Here are riv-nut answers! This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Used driver side (left hand) grade "B" manual side mirror for the Mercury Cougar. This is your plain Jane manual adjust mirror for the driver side of your 1969 or 1970. Worn finish, scratches, often will have light pitting. Uses same base mounting pad as all 1969-70 Cougar driver side mirrors.Ford part # C9WY-17696-B. Do you have riv-nut questions? Here are riv-nut answers! ...

This mirror features a painted base which was used on the Sport Special and Eliminator models. XR7 models used a chrome base except the very late cars. Good used mirror ready to be painted and installed. We test the remote function before we send. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

NOS driver side (left hand) external remote mirror assembly for the Mercury Cougar and is for 1969 Cougar only. Ford Part # C9WY-17682-D. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

This one year only, 1969 S code 390-4V or 390IP (Improved performance). Same jog as the 428CJ snorkel. It is technically a 428CJ snorkel with the addition of an adapter on the heat riser opening reducing it down for use with a 2 inch I.D. paper "S" tube. Ford part number C9OZ-9A626-C.

For all 1968 through 1970 R and Q code 428CJ and SCJ air cleaners. Snorkel has the opposite jog than 390GT snorkels. This one jogs towards the rear of the engine. Originally this snorkel should have had an ink stamp of C8OF-9A626-A or -B. Ford MPC number C8OZ-9A626-C.

Application would only be for 1969 Boss 302 Eliminators and Boss2 Mustangs. Ford part number C9ZZ-9A626-C

This reproduction cigar / cigarette lighter socket is a good fit and is easy to install. This lighter socket also comes with the retainer. Replaces Ford part # C6ZZ-15055-B.

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

This sound deadener is comprised of one layer of tar sound deadener and a layer of Jute. Here is a shot of the original sound deadener pulled (slightly) apart to expose the en-capsuled insulation.  This new OEM style sound deadener is very similar, but is lacking the extra layer of tar on the bottom.  This can be overcome by adding the tar only kit to this kit.  This combination will come by far the closest to OEM than any other kit available! ...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.

Used angled chrome spacer for any 1969 Mercury Cougar or Ford Mustang. Good used part with very good chrome plating, usually one of the small locating tabs will be broken off of the back. Still a great value compared to the reproduction, and installs fine without the one tab on the back. Replaces Ford part number C9ZZ-11574-A.

C7SZ-3D600-A  Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 1/2" thick. Same thickness as the pedestal bracket for air conditioning.

Early version of the FE engine / Transmission spacer plate. Has 1 medium sized hole instead of 3 smaller holes above the crankshaft. Originally was for either automatic or manual. Ford part #: C3AZ-7007-A.

Reproduction 6 1/4" Spare Tire Mounting Bolt 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

NOS spare tire lock for the 68 - 73 Cougar Mustang and Torino. Spare tire locks were first offered as an option in 1973, but will fit on any year from 1968 to 1973. The ford master catalog shows that all years from 68 - 73 whether it be Cougar, Mustang or Torino all had the correct size stud for this lock to fit. Fits spare tire hold down J bolts with 1/2-13 course threads, common on Fords 1968-73.  Ford part number D3FZ-1386-A. J bolt not included. ...

Used spare tire lock for the 68 - 73 Cougar Mustang and Torino. Spare tire locks were first offered as an option in 1973, but will fit on any year from 1968 to 1973. The ford master catalog shows that all years from 68 - 73 whether it be Cougar, Mustang or Torino all had the correct size stud for this lock to fit. Fits spare tire hold down J bolts with 1/2-13 course threads, common on Fords 1968-73. Ford part number D3FZ-1386-A. J bolt not included. This icon means that we're looking...

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...

This clips affixes the plastic speedometer gear to the cable. Some have found that this OEM original clip fits a little better than the reproduction we offer. *Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

This is a good used speedometer cable from a 1969 - 1970 Mercury Cougar with a FMX transmission. The cable housing has no burns and the fragile plastic squeeze clip that fastens it to the back of the speedometer is not broken. Keep in mind that some 1970 models use a two part cable. This cable will work in place of the two part cable seen on some 1970 cars. This cable measures 58 1/2" at its very most outer ends.

New manufactured 4 speed, speedometer cable for use drag pack 1969-70 Mercury Cougar and Ford Mustang. Has correct end for fitting onto factory gear reducers. Drag pack ring an pinion ratios were 3.91:1 and 4.30:1, which needed a mechanical gear ratio reducer in addition to a normal speedometer gear.Cable Length: 70"

According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. https://www.428cobrajet.org/id... This is a part that we will probably never...

According to the Master Parts Catalog (MPC), Early (before Jan 31, 1969) Cougar with a 3.91 or 4.30 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. Also found on 1970 4 speed Mercury Cougar and Ford...

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. Replaces Ford Part #: C8ZZ-17294-A.

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. This is a part that we will probably never have on hand, but would love to document. If you have one of these adapters, we would be interested in being able to put detailed pictures of it on this listing. Please let us know. We hope to have a reproduction of this adapter...