1969 Mercury Cougar

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Reproduction stamped steel passenger side (right hand) front inner apron for the Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Guide that measures 10 5/8" long held in place by the outer trim that has four screws. Driver and Passenger are interchangeable.

Reproduction driver side inner rocker panel for the 69 - 70 Cougar Convertible

Reproduction passenger side inner rocker panel for the 69 - 70 Cougar Convertible

This is for your automatic transmission 1969 Cougar XR7, Standard, Decor or Eliminator console. The 1969 is unique over the 70 in that it has a provision for your seat belt buckles. This requires an additional woodgrain insert, we also have one listed that does not require the additional insert (no holes). Absolute perfection in every detail, if all reproductions were this nice there would be almost no market for used parts. *Note - This console part does have pre-drilled holes for installing...

This console bezel is for your three or four speed manual transmission 1969 Cougar. The 69 is unique over the 70 in that it has a provision for your seat belt buckles. This does not require an additional woodgrain insert, so it is not technically correct for your Cougar. We list this unit because there is no quality XR7 burl grained inserts available at this time and some customers prefer the clean uncluttered look of the plain camera case finish. Absolute perfection in every detail, if all...

Grade "A" condition with rich luster on the woodgrain. Will have a few minor blemishes usually on the XR7 emblem and aluminum surround. No dents or scratches.Check out this video

Grade "B" condition with dull luster on the woodgrain. Will have blemishes usually on the XR7 emblem and aluminum surround. Check out this video

This listing is for the woodgrain only, no emblem or aluminum surround is included. Grade "A" condition with no extra holes, scratches or dings. Show quality, no excuses, satisfaction guaranteed.Check out this video

Used interior door release mechanism. Other Ford names include: door remote, control, linkage assy, latch assembly. The spring is the weak link on these parts. Passenger and driver side are different, this is for the driver side only, comes with attaching parts as shown. Replaces Ford part number C9AB-6221819-A.

Used interior door release mechanism. Other Ford names include: door remote, control, linkage assy, latch assembly. The spring is the weak link on these parts. Passenger and driver side are different, this is for the passenger side only, comes with attaching parts as shown. Replaces Ford part number C9AB-6221818-A.

Reproduction steel inspection cover for all 67 - 70 Cougars or Mustangs with 390, 427, or 428CJ engines with the C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.Replaces Ford part number C6AZ-7986-A

Steel inspection cover for all 1967 Cougar or Mustang with any of the FE engines 390, 427, or 428CJ and C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter. Usually will have a casting number of C6AP-7986-A stamped on it, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.*Note - Some of these plates do not have the vent, or dimple at the bottom, like in the picture.Please keep in mind that this is a 40+ year old used item....

Reproduction dust and safety cover for 69 - 73 Cougars and Mustangs with the FMX (X code) automatic transmission. Access plate for the torque converter and flex-plate.NOTE - Although the FMX and the C4 inspection plate look similar visually, they are in fact different sizes with different bolt spacing.

Used dust and safety cover for all 69 - 73 Cougars and Mustangs with the FMX (code X) automatic transmission. Access plate for the torque converter and flex-plate.

Grade B used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This cover will have some rust and a dent or creases. Find the Grade A cover here.

Reproduction inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch.Replaces Ford part number C3AZ-6366-A.

Reproduction 21 pc installation screw kit to install the well liner on your 69 - 70 Convertible Cougar or Mustang.

Reproduction installation kit for the 1969 Cougar dash pad.

Replaces Ford Part # C9ZZ-10914

Insulator for mounting the ammeter on any 1969-73 Mercury Cougar or Ford Mustang with factory ammeter in gauge cluster. Also used on other Ford cars with ammeter. Casting number C9ZF-10C914. Ford Part # C9ZZ-10C914-A

New foam insulation for the lower tube of the steering columns. Can be used on fixed and tilt columns, from 1968-73, on all Mercury Cougars, Ford Mustangs, and most all other Ford steering columns with a lower tube with inside diameter of 1-5/8 inches. The originals have almost always disintegrated. Adhesive probably isn't needed, but we recommend just a little drop of something to hold it in place. This is a dense foam insulation ring. DIY guys, this material can be found in bulk at home...

Self adhesive cork insulation tape for use on any 1967-73 Mercury Cougar or Ford Mustang with air conditioning. This is original style insulation wrap that adheres firmly to all metals. Material is 1/8 inch thick, and 2 inches wide, comes in a roll of 3 foot length. Perfect material for wrapping expansion valves, and joints prone to condensation.   

Reproduction insulator for the lower portion of the steering column found on all 1969-73 Mercury Cougar or Ford Mustangs. Unique slide in plastic bushing or insulator, which slides into the bottom tube of both fixed and tilt columns. Most originals are broken or missing. Two sizes of insulators, please verify year and diameter.1968 tube measures 1 3/8"1969 - 1973 tube measures 1 5/8"*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this...

Used tube insulator for the lower portion of the steering column found in 1969-72 Mercury Cougar or Ford Mustang. Because of the very fragile nature of this unit, stock is limited. Reproduction version is normally available, see related items. Ford part # C9AZ-3E629-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction Rear Leaf Spring Center Mount Insulator Pad for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody StyleNotesYearMercur...

Set of Four Reproduction Rear Leaf Spring Center Mount Insulator Pads for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody...

C9OE-9425-A or -F Cast iron intake manifold used on all 1969-70 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C9OE-9425-A or -F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9OZ-9424-A. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

C9OE-9425-B Cast iron intake manifold used on all M code 351-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9OE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9OZ-9424-B. Casting number can also be C9OE-9425-D, or C9OE-9425-E. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air...

Used C8OE-9425-C Cast iron intake manifold used on all 1969 - 1970 Q and 1968 - 1970 R code 428CJ and 428SCJ engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C8OE-9425-C . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford part number C8OZ-9424-B.  Current date code is 9C25 or March 25, 1969 and 0A19 or January 19, 1970. *Trivia - One of the heaviest...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2K.    Aqua Decor Upholstery to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2K.    Aqua Decor Upholstery to cover the rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like aqua are not...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2A.    Black Decor Interior Upholstery Kit to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2A.    Black Decor Interior Upholstery to cover the rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like aqua are...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2D.    Dark Red Decor Upholstery to covet the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2D.    Dark Red Decor Upholstery to cover the rear seat for the 1969 Mercury Cougar Convertible. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of...

Upholstery components have an ETA of 10 - 12 weeks. Door Tag Trim Code: 2B.     Light Blue Decor Upholstery kit to cover the front buckets and rear seat for the 1969 Mercury Cougar Convertible. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2B.    Light Blue Decor Upholstery to cover the rear seat for the 1969 Mercury Cougar Convertible. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of...

Upholstery components have an ETA of 10 - 12 weeks. Door Tag Trim Code: 2G. Light Ivy Gold / Light Green Decor Upholstery to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses. *NOTE* Some of the more unique...

Upholstery components have an ETA of 10 - 12 weeks. Door Tag Trim Code: 2G. Light Ivy Gold / Light Green Decor Upholstery to cover the rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses. *NOTE* Some of the more unique colors like aqua...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2Y.    Nugget Gold Decor Upholstery to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2Y.    Nugget Gold Decor Upholstery to cover the rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like aqua are...