1969 Mercury Cougar

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

Replaces Ford part #C1SZ-13783. Replaces burnt, cracked or missing original lenses located above the rear package tray.  Two required per car, sold individually.

This is the chromed correct die cast construction for your 1969 Cougar, 1970-73 used plastic but these will fit fine and look better than the plastic units. Great Quality. Sold individually, two required per car. Part of the XR7 package. Available on other hardtop models, part of the Courtesy Light group option. Option included, engine compartment light, trunk light, map light and these rear quarter panel lights for the back seat. Replaces Ford Part #: C4SZ-13776-B.*Trivia Dearborn built...

These lights feature beautiful chrome bezels and bright white lenses. Mounting hardware, bulbs and sockets with pigtails are included. These were used on the XR7 and all Cougars equipped with Decor level interiors in 1969 and 1970. These are AWESOME reproductions worthy of the most exacting of restorations. You will be VERY happy with these lights. Sold as a pair. Replaces Ford Part #: C9WY-13776-A & C9WY-13777-AThese use a 212 bulb.Click on images to enlarge. ...

C9WY-13777-A-AGRADE Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. Hardest side to find in primo condition most get dinged up from errant seatbelts. These are available in reproduction. Nice Quality!These use a 212 bulb. ...

C9WY-13777-A Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses. These are available in reproduction. Nice Quality!These use a 212 bulb.

New Old Stock Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. These are available in reproduction. Nice Quality!Ford part number C9WY-13777-A. These use a 212 bulb.

C9WY-13776-A Right side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses. These are available in reproduction. Nice Quality!These use a 212 bulb.

69PACKLIGHTS Right and left lights are the same. They are located on the "C" pillar just above the rear package tray. These 1969 and 1970 lights look the same from the outside, but are differently constructed. The 1969 variety are chromed pot metal, the 1970-72 style are plastic with plastic chromed bezels. The 1970 style are the service replacements and are much easier to find and restore. These 1969 light assemblies are prone to pitting. Grade B is driver quality, will have pitting in the...

Since the reproduction is no longer available anywhere, we've taken a used plug and our electrical department has pieced it together to make a useable plug. The Eliminator uses the XR7 harness but not the XR7 rocker switches in the center of the dash. This bypass plug completes the circuit left open when no XR7 switches are plugged into the harness.

The Eliminator uses the XR7 harness but not the XR7 rocker switches in the center of the dash. This bypass plug completes the circuit left open when no XR7 switches are plugged into the harness.Ford part # C9WB-13B676-A

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

Used pivot cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

Reproduction ashtray cover assembly for the center console found in the Mercury Cougar or Ford Mustang. Does not include ashtray receptacle, which is sold separately. Replaces Ford part # C9ZZ-6504814

Used ashtray cover assembly for the center console found in the Mercury Cougar or Ford Mustang. Does not include ashtray receptacle, which is sold separately.. NOTE: When ordering, mention what color you're looking for in the order comments and we will do our best to accommodate.

Covers the metal, foot operated headlight dimmer on the driver side floor pan. Replaces ford part #: C5ZZ-13533-A.

Used quarter window stop, cover plate, for any 1969-70 Mercury Cougar and Ford Mustang. These were originally painted body color, and were laid on either inside the front cowl or the package tray for painting. The one for the quarter is roughly1" x 2-7/16 inches long, the holes are 5/16, and the spacing is 31/32" on center to match the stop. Replaces Ford part number C9ZZ-6530068-A.

Access cover, unique to tilt steering columns. This is the little cover on the left side by the turn signal lever. We only find these occasionally as 'spares'. In most cases it will need to be painted to match your steering column color. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

These are Grade "A" no excuses panels. This panel can be rather difficult to fix so we suggest you buy the best from the get go considering the low price. These will have no filler, no damage and often times will still bear the original paint.Ford part # C9ZZ-6502010-A.

These are Grade "B" cowl cover panels. These units may have one or two small dents, but can be an easily straightened and made to be perfect. Ford part # C9ZZ-6502010-A.

Reproduction cowl center panel for Mercury Cougar and Ford Mustang.

Reproduction 2 piece cowl panel for the Mercury Cougar or Ford Mustang.Here's our video to help you fortify your Cougar!

Crankshaft oil slinger for all small block Ford V-8's, starting 1963 until at least through 1973. 1963-68 289 and 289 HiPo engines. 1968-73 302 engines, 1969-70 Boss 302 engines, 1969-73 351W engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter about 2-7/8 inches. Ford part number C3OZ-6310-A.

CRC contact cleaner is intended for cleaning sensitive electronics and electrical equipment. Great for cleaning edge connectors, buss bars, circuits, contacts, printed circuit boards, switches, circuit breakers, etc. Safe on most plastics.

Reproduction of the very hard to find crossmember for any 67 - 70 Cougar or Mustang with the 390 or 428 engine and the C6 transmission. Replaces Ford Part number C7ZZ-6A023-B

For all 1969 and 1970 Cougars with H code 351-2V and M code 351-4V engines and FMX automatic transmissions. This part weighs 2.66 pounds and when set on a level surface the height of the mounting hole on the driver side measures 3" on center and the passenger side 3 1/8" on center. Ford part number C9ZZ-6A023-A. *NOTE* The picture with all four crossmembers in a line shows the three versions of the small block C-6 and FMX units in the foreground and the last is the big block C-6 unit. Notice...

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

This product has received the 'Crappy Product' certificate. Items that receive the 'Crappy Product' certificate are products that we carry for comparison purposes as they are often the version offered by other vendors or because it is the only version available. We would not be willing to use these parts on our own cars, and we do not recommend purchasing these parts. WE ARE NOT ABLE TO ACCEPT RETURNS FOR THESE PARTS. This is the reproduction cross member offered by most of the Mustang...

Good original part that has not been noticeably twisted, bumped, bent, or heavily rusted. Notice the factory indentations that are a result of the manufacturing process (dent from jig). Also know that there is always at least a couple minor dings or scrapes from decades of being the lowest point of the car. Much better fit than repro and note the repro is made from thinner gauge steel. Also know that we generally do not bead blast our used parts before sending them but often we show them on...

This reproduction radiator support crossmember is correct for the 1967-68 Mercury Cougar and Ford Mustang, but will work on any 1967-70 Cat or Pony.Replaces Ford # C7ZZ-6510852-B or C9ZZ-6510852.

New crossmember to adapt the Tremec TKO manual transmission to the Mercury Cougar or Ford Mustang. This unit can also be used for the Ford AOD. 

Parking brake return spring cup for the 69 - 73 Cougar or Mustang. This cup sits at the end of the spring and is held in place by an adjusting nut. It's used to keep the spring from sliding off of the front emergency / parking brake cable.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

1969 Front unibody cut, these 1969 Mercury Cougar front structures all have reinforced shock tower braces like the 390 and 428 Cobra Jet Mustangs. Mustang guys, please note, we do not have them without these braces. This cowl only ships with the holes for the factory air conditioning. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford...

1969 Front unibody cut, these 1969 Mercury Cougar front structures all have reinforced shock tower braces like the 390 and 428 Cobra Jet Mustangs. Mustang guys, please note, we do not have them without these braces. This cowl only has the holes for the heater hoses only, not cut for factory air conditioning. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a...

Comes with good shock towers, front aprons, and core support. This is a great value for those that need to replace multiple parts upfront as you will not only get factory joined parts that will save you money and time, but it will also  preserve the value of your car. With a clean Western cut like this, one should be able to install it so that nobody would ever know your car has had anything replaced. You will have to call to order this one. Expect to pay about $300 for crating and...

Single cylinder head from 1969 Mercury Cougar H or M code 351W engines, 351-2V and 351-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C9OE-6090-A.These weigh 53 lbs. each, and cannot be combined with other items unless shipping truck freight. ...

Single cylinder head from 1970 Mercury Cougar H code 351W engines, 351-2V. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0OE-6090-C. 1970 351 Windsor engine, not to be confused with the 351 Cleveland engine from the same year.These weigh 53 lbs. each, and cannot be...

Single cylinder head from either a 1968 X code 390-2V or 1969 Mercury Cougar with 390-4V or 390-IP engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1 (9.5:1 with X code). Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes....

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash. We think that it is Ford part number 382184.

Used highly collectible Dan Gurney slot car racing track made by the Republic Tool and Manufacturing Corporation in Los Angeles California. Open box and lightly used. Both cars are intact, and the decals have been placed on the the vehicles and the track. Everything is good condition, but the cars have not been tested and the red car has had it's wheels painted. Other than that, this is a rare and truly great find. Features the Mercury Cougar Logo on front of the box.

Plastic filler piece that goes over the steering column and bridges the instrument cluster portion of the dash pad. Ford calls this part a "PANEL" (Instrument Panel Cluster) in the Master Parts Catalog. "A" grade used is one without cracks or chips. Put a desired color in the comments section of the online order. We suggest planning on 'painting to match your interior'.  Current color appears to be Aqua Blue. This icon means that we're looking to buy this part!WCCC is a buyer of used and...

Complete very nice grade A bezel for the standard or decor level interior for both the 1970 and 1969 Mercury Cougar. Includes a metal "COUGAR" emblem. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you...