1969 Mercury Cougar

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

New Old Stock turn signal flasher for all 1970 Mercury Cougars. For most applications, we highly suggest you upgrade to our solid state version of this unit.  Ford part #D0WB-13350-A,  D0WY-13350-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...

This A/C suction service valve fits on top of the compressor and is an exact copy of the original unit.Good for R-134A, but still compatible with R-12.Fitting sizes:Male end 7/8"Female end 9/16"

Used Servo Assembly for 1969 Mercury Cougar and Ford Mustang with speed control. The Servo is the rubber bellows. Part of the accelerator pedal assembly in the passenger compartment.Ford part number C9ZZ-9C735-A.

Shaft or rod for the heater core damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C9ZZ-19C774-B.*Note will not work in 1967-68 A/C boxes. ...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any 1969 Mercury Cougar equipped with factory speed control. *Note - For use with 1969 factory cruise control.

NOS shaft bushing for the grille / headlight eyelid door for the Mercury Cougar, a handfull of other Mercurys, Lincoln and a few Pontiacs. This NOS bushing mounts to the grille for the headlamp operating shafts. New in the Ford box, these hardly ever survive after 40 years. Technically not needed, and most never knew they existed. Sold as a pair, one for each side.When mounted these are tight, it was no wonder they are seldom seen on cars. Even the NOS bushings are tight. We recommend...

Used plastic sheath that covers the bolted buckle end of where your shoulder belt attaches to the roof section of your car. Sometimes when removing the bolt from your shoulder belt, this sheath will tear if the plastic has become stiffened. Although it does not affect it's usage, sometimes it's best to simply replace it.  NOTE: To remove this sheath, you will have to pull some slack from the seat belt up through the opening at the top in order to push up on the sheath to access the...

This 1969-70 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390 / 428CJ's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...

Attractive reproduction of a very popular, over the counter Mercury dress-up accessory. The only Cougars that came from the factory with this real wood shifter were the 1970 Eliminator and 1968 XR7G. The XR7G used a gold Cougar "Walking Cat" emblem and the 1970 Eliminator used the silver emblem. Of course this will look great on any 1967 - 1973 Cougar. Click on images to enlarge. ...

Mercury Cougar shift handles never came covered in real leather from the factory but what a cool upgrade! We sell a lot of these and the feedback has been great. We also carry the original plastic covered (simulated leather) reproduction XR7 shift handles in several colors but this real leather handle comes in black only.

Used to block light from escaping around shifter stem seal. Fits 1969-73 Mercury Cougar and Ford Mustang as well as 1971+ Pinto, Bobcat, Maverick, and Comet with floor shift automatic transmissions. The 90 degree notched portion straddles the set screw on the cast light housing. Most shifters (almost all) we see do not have this part in place any longer. Ford part number C9ZZ-7E130-A.Note: This fits perfectly on the shifters we have tried, but several customers have commented that it was too...

This keeper affixes to the top of the plastic indicator arrow.  Screws included. Check out our video on rebuilding your shifter below: ...

Very hard to find 69 - 70 Shelby / 68 - 69 Cougar 4 speed shifter knob. These very rarely come up for sale used and when they do they are expensive. Correct for 1968-69 Mercury Cougar XR7 and 1969-70 Ford Shelby Mustang, all with 4 speed manual transmissions. Ford part number C8WY-7113-C. Check out our video on rebuilding your shifter below: ...

Clean no nonsense look. 12MM Threads. Check out our video on rebuilding your shifter below:

Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

3 Speed manual transmission shift control assembly for any 1969 Cougar or Mustang. Control assembly only, no rods or chrome lever. C9OZ-7400-B Check out our video on rebuilding your shifter below: ...

C9OZ-7400-B3Assembly Factory 3 Speed manual transmission shift control assembly for any 1969 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 390-4V engine. Check out our video on rebuilding your shifter below: ...

C9OZ-7400-AAssembly 4 Speed manual transmission shift control assembly for any 1969 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on all V8 Mustangs and Cougars. Check out our video on rebuilding your shifter below: ...

Used automatic shifter bezel / indicator assembly for all Mercury Cougar and Ford Mustang with or without consoles. These are the best used ones from our inventory. These will have some minor issues with the chrome plating and most often need some detailing on the black pebble grain. Consider also purchasing a new seal, shift indicator lenses may or may not meet your requiements. Doesn't meet your requirements? We have very nice quality 1969-70 reproduction shift plate bezels also available....

Metal core base as original, correct texture. If you have a 1970 with a Hurst four speed then the one with the rectangular hole is correct for the Hurst shifter. Replaces Ford part # C9ZZ-7277-A. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

C9ZZ-7210-A Shift lever for all 1969 Mercury Cougar and Ford Mustangs. Manual 3 speed only, 4 speeds are different. *Note - Must be used with Trunion C9OZ-7210-B, sold separately. Check out our video on rebuilding your shifter below: ...

C9ZZ-7210-B 4 Speed shifter lever for any 1969 Mercury Cougar and Ford Mustang with V-8 engines. *Note - Must be used with Trunion C9AZ-7210-J, sold separately. Check out our video on rebuilding your shifter below: ...

Used 4 speed manual transmission shift control assembly for the Mercury Cougar or Ford Mustang.Ford part # C9OZ-7400-A. Check out our video on rebuilding your shifter below: ...

Adapter plate for mounting the 3 or 4 speed shifter control assembly to the Top Loader transmission.Ford part # C9ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...

C9OZ-7210-B "U" shaped bracket that attaches the 3 speed shift lever to the shifter control assembly. For use on all 1969 Mercury Cougar and Ford Mustangs with the 3 speed shift lever. Bottom bracket only, called a Trunion (see illustration). *Note - Must be used with 3 speed shift lever C9ZZ-7210-A. Check out our video on rebuilding your shifter below: ...

C9AZ-7210-J "U" shaped bracket that attaches the 4 speed shift lever to the shifter control assembly. For use on all 1969 Mercury Cougar and Ford Mustangs with the 4 speed shift lever. Bottom bracket only, called a Trunion (see illustration). *Note - Must be used with 4 speed shift lever C9ZZ-7210-B.

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

Good working grade "A" driver side (left hand) mirror that will look as good as the one shown here. Since the wand is recessed into the door panel on the 1969 Cougar, the wand is not prone to breaking off like the 1970 version which protrudes straight out. NOTE - Cable length should be 18" from the base of the mirror to the inner end of the remote wand assembly. In order to keep the cable from hitting the window, there's usually a clip to hold it away from the glass. This clip is hard to come...

Good working grade "B" driver side (left hand) mirror that most likely will not have as good of chrome as the one shown here. Since the wand is recessed into the door panel on the 1969 Cougar the wand is not prone to breaking off like the 1970 version which protrudes straight out. NOTE - Cable length should be 18" from the base of the mirror to the inner end of the remote wand assembly. In order to keep the cable from hitting the window, there's usually a clip to hold it away from the...

Used driver side (left hand) grade "A" manual side mirror for the Mercury Cougar. This is your plain Jane manual adjust mirror for the driver side of your 1969 or 1970. Uses same base mounting pad as all 1969-70 Cougar driver side mirrors.Ford part # C9WY-17696-B. Do you have riv-nut questions? Here are riv-nut answers! This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Used driver side (left hand) grade "B" manual side mirror for the Mercury Cougar. This is your plain Jane manual adjust mirror for the driver side of your 1969 or 1970. Worn finish, scratches, often will have light pitting. Uses same base mounting pad as all 1969-70 Cougar driver side mirrors.Ford part # C9WY-17696-B. Do you have riv-nut questions? Here are riv-nut answers! ...

These are almost impossible to crimp back together after your mirror has been repaired or re-chromed. Fits many Ford products from the 1960's and 1970's.

NOS driver side (left hand) external remote mirror assembly for the Mercury Cougar and is for 1969 Cougar only. Ford Part # C9WY-17682-D. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! ...

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

This one year only, 1969 S code 390-4V or 390IP (Improved performance). Same jog as the 428CJ snorkel. It is technically a 428CJ snorkel with the addition of an adapter on the heat riser opening reducing it down for use with a 2 inch I.D. paper "S" tube. Ford part number C9OZ-9A626-C.

Application would only be for 1969 Boss 302 Eliminators and Boss2 Mustangs. Ford part number C9ZZ-9A626-C

This reproduction cigar / cigarette lighter socket is a good fit and is easy to install. This lighter socket also comes with the retainer. Replaces Ford part # C6ZZ-15055-B.

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

Reproduction sound deadener for the seat divider on the 1967 - 1970 Mercury Cougar. This reproduction is as close to the original as possible, and is comprised of a mastic material. This item is trimmable and will fit bot the 67 - 68 and 69 - 70 seat divider.

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.