1969 Mercury Cougar

Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Portland / Beaverton, Oregon.  Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.

Restored rear license lamp assembly for all 1969-70 Mercury Cougars. Plated and restored lamp housing with original glass lens, new gasket, bulb, and wiring pigtail with integral rubber body plug.

Lamp housing with original glass lens, wiring pigtail with integral rubber body plug. Driver quality part. #97 Bulb available. We often find damaged wires with these lights left on our rear bumper cores. Guaranteed to work with no cuts or splices. Specified as a Cougar part in the Master Parts Catalog, but the wiring harness has imprinted on it C9ZB-13412-A. However, it is unknown whether or not it fits the Mustang.

Concourse correct reproduction chrome GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. This is an extremely hard piece to find used, and even rarer in NOS form, but now we can offer you this new unit that is made from the original tooling! It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine,...

This rechromed lid is found on many years and cars 1968 - 1971. The diameter of the lid is just over 17 3/4", fits on 17.84" air cleaner bases. Application Mercury Cougar Ford Mustang 302 and 351 engines without ram air. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. This lid was chromed in several...

This was the inner air cleaner lid used on the Mercury Cougars equipped with a 428 Ram Air Cleaner or 429 Cobra Jet Ram Air Cleaner assembly. Although you will often find chrome under the blue engine paint on these lids they are in fact supposed to be painted from the factory. This lid is 14-1/8 inches in diameter. The reason you will often see chrome underneath the paint is that this is the same lid used on the 1967 427 GTE, 289 HiPo equipped early Mustangs and 390 GT / GTA Fairlanes and...

This lid is found on many years and cars 1968 - 1971. The diameter of the lid is just over 17 3/4", fits on 17.84" air cleaner bases. Application Mercury Cougar Ford Mustang 302 and 351 engines without ram air. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. This lid was chromed in several applications,...

This engine compartment lamp assembly includes lamp socket, bracket, mercury switch, and length of wire. A bit of investigation shows us that an inline fuse was used on the single wire and it has an amp rating of 7.5 amps.Replaces part # C9WY-15702-A

"C" pillar courtesy light bulb which is also good for under under dash courtesy lights on 67 - 70 Cougars.

This used socket is found on the backside of your instrument cluster and takes a 194 bulb.

Our excellent used sockets are a better price and better quality.This item does not come with a 194 bulb.

Original good used part with no cracks, but may be brittle from age. These really are getting hard to find in mint condition. For the money, the reproductions are every bit as good as the originals. They are also available in red and yellow.Replaces Ford part number C4VY-10B870-A.

Available in original blue light diffusers or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have, there are different numbers of diffusers (filters) needed for different years and models. Sold as a set of four. SOLD AS SET OF FOUR(4).67 - 68 Cougar Uses6 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) 2 - Oil Pressure Gauge (XR7)69 - 70 Cougar Uses5 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) ...

Available in original blue light diffuser or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have there are different numbers of defusers (filters) needed for different years and models. SOLD AS SET OF FOUR(4). 67 - 68 Cougar Uses 6 - Instrument Cluster (XR7 or Standard) 2 - Clock 2 - Oil Pressure Gauge 69 - 70 Cougar Uses 5 - Instrument Cluster (XR7 or Standard) 2 - Clock ...

Ford calls this part a 'mask'. This clamps to the chromed lever and holds the socket and bulb that are attached to the neutral safety switch, which are the shifter indicator light for the floor shifter. This cast piece will not have stripped treads or be corroded. It also fits 1971 and newer Maverick and Comet with floor shifters only. Ford part number C9ZZ-7B052-A. Check out our video on rebuilding your shifter below: ...

Used small wiring harness with light socket that illuminates the under dash ashtray on 1969 Mercury Cougars without console. Takes a 1445 bulb, which is sold separately. This light should work on a Mustang, since they used the same ashtrays. The female bullet connector is for plugging in the heater or A/C control light. Comes with bulb shroud with clip as shown.Ford part # C9WB-13A726-A.

Reproduction small wiring harness with light socket that illuminates the ashtray on 1969 Mercury Cougar and Mustang with console. Takes a 1892 bulb, included in this reproduction.  Replaces Ford part # C9ZB-13A726-A.

Used small wiring harness with light socket that illuminates the ashtray on 1969 Mercury Cougar and Mustang with console. Takes a 1892 bulb, which is sold separately. Ford part # C9ZB-13A726-A.

Reproduction glove box light switch for the 69 - 70 Cougar or the 69 - 73 Mustang.

Glove box or glove compartment light with switch. Fits 1969 Mercury Cougar, 1969 Ford Mustang. Used switch and wiring assembly, tested and working. 1969 has a part number C9WB-14413-B on the wire. Will work on a 1970 Cougar or Mustang. The wire on the 1969 pigtail is a larger gauge than the 1970 equivalent.Fits 69 CougarFits 69 Mustang

Accessory pamphlet "For Active People". 31 pages Volume 69 MSD-1A. This brochure highlights everything from the floor mats to an 8-track.

NOS Rand McNally Lincoln Mercury atlas and travel guide, originally distributed to customers through their local dealer. Includes state, city and "special maps" that include the US, Central America, Mexico and Puerto Rico. Also includes a special features section with points of interest.

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.

Reproduction wheel cylinder link pin. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Sold individually. Ford part number B7A-2042-A.

Reproduction set of wheel cylinder link pins. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place.Sold as a set of four.

1969-70 Mercury Cougar and Ford Mustang latch rod that links the door latch and the inside door handle, right or left side door. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number C9ZZ-6521940-B.

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Manual control shift linkage assembly for a floor shift FMX transmission in any 1969 Mercury Cougar or Ford Mustang. Comes as shown.  1969 linkage is different than 1970, 1970 included a provision for the steering column lock out rod. Check out this video

Linkage arm that attaches to the windshield wiper motor that is unique to the 1969-70 Mercury Cougar and Ford Mustang. These are marked 9Z, among other things the slot is specifically indexed for the 69-70 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Replaces Ford Part # C7AZ-6243505-B Click on images to enlarge.

Keyed alike as the originals were, includes two keys, trunk cylinder gasket and retaining clip. Ready to go kit for your 1969 - 1970 Cougar.

Originals keyed alike with Ford key. code on glove box lock matches the trunk lock perfectly. Includes 2 Ford keys, trunk cylinder gasket and retaining clip. Ready to go kit for your 1969 - 1970 Cougar. will fit 1971-73 Cougars, but trunk clip may be different. These used originals are much better than the reproduction lock sets.OEM FoMoCo parts.

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. C9WY-6543283-A.1969 and 1970 Cougar only.

Includes two door lock cylinders, two door cylinder gaskets, two keys and one ignition lock cylinder.  Made by the original OEM supplier.  That being said, they do not make them like they used to. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.

Correct style nut with captured washer for attaching hood scoops, 1969-70 Mercury Cougar inside door handles, and 1967-68 trunk lock. Correct nuts would have been black phosphate, these are shiny gold as shown.

The four part, die cast vinyl top trim kit requires 15 (right rear under back glass is the odd ball that requires five fasteners) of these speed nut fasteners. These speed nuts also can be used on the 1969-70 Mercury Cougar XR7 dash courtesy light bezels, two for attaching that bezel to the dash pad.*NOTE* These speed nuts only work with factory installed die cast vinyl top mouldings.*NOTE* The factory nuts had a drop of silicone or trim adhesive inside the bowl that acted as a seal. This...

1969-70 Mercury Cougar and Ford Mustang door lock rod. This is the short rod that goes between the door key lock and the latch mechanism. Same part right or left, just under 6 inches in length, no threads on this rod. Ford part number C9ZZ-6522134-A.

Includes three cylinder clips, two door cylinders, two door cylinder gaskets, two keys, one trunk cylinder, one trunk cylinder gasket, and one ignition cylinder. Made by the original OEM supplier. Makes 1 key fit all our locks! Replaces Ford part #: C9AZ-6222050-A

[No Description Provided]

Reproduction power window lock out switch for all 1969-72 Mercury Cougar and most all other Ford - Lincoln - Mercury cars with power windows in the 1969-72 time frame. Regardless of what you may have been told, this fifth switch found closest to the dash is not a power door lock switch rather it is to "lock-out" the power window on the passenger door and the two windows in the rear so the passengers cannot operate their power windows via their individual switches. Original Ford number...

Regardless of what you may have been told, this fifth switch found closest to the dash is not a power door lock switch rather it is to "lock-out" the power window on the passenger door and the two windows in the rear so the passengers cannot operate their power windows via their individual switches. Treat this switch with care (try not to ever use it) and lubricate it. These are very delicate and hard to obtain. Ford number stamped on the side C9AB-14A695-B.

Used locking lever for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. Two required per car. Here is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This is a rebuild service in which we will replace the locking pawl and cable. We provide this service for Cougars, Mustangs and T Birds.Ford part number C9ZZ-3E520-A THIS SERVICE REQUIRES THAT YOU SEND IN YOUR CABLE IN ADVANCE.

New manufactured Tilt / Tilt-Away cable for any 1968-69 Mercury Cougar or Ford Mustang with factory tilt steering column. All new parts developed by our in house steering column expert DW. Not created from used parts. The cable sheathing will not split or crack over time like the originals.Replaces Ford part number C9ZZ-3E520-A*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

Keep in mind we can repair these for half or less of the price we charge to sell one outright. We can also install parts and or refurbish these columns. Ford part number C9ZZ-3E520-A *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...