1969 Mercury Cougar

New Old Stock. This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

Reproduction 22" pigtail for the 67-69 front turn signal wiring harness. Please Note: The Cougars are wired differently than some Mustangs. On some Mustangs the brown wire goes to a male plug.   This plug is a reproduction of the Cougar plug. Here is an example from the reproduction tail light we sell showing the difference: For installation on a Cougar, match up: Black Wire Black Wire Light Blue Wire Light Blue / Off White Wire Brown Wire Brown Wire ...

Reproduction green tinted windshield that features a blue tinted band a crossed the top of the windshield. Not only will this unit look great, it will fit perfectly as well. Planning on installing the glass yourself? We also sell the glass to window channel weld. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate displayed....

Reproduction brake line clamp kit for the Mercury Cougar or Ford Mustang.

Replaces Ford Part # 359747-S

Used factory installed vented fuel, or gas cap as installed on 1967-69 Mercury Cougar 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap.We stock these in limited quantities, and will have an intact paper gasket. Correct "VENTED" embossed and has the "S" stamped onto the center rivet. Price is established by demand, and these normally are only needed for very high level restorations or strict concours judging...

Driver quality complete assembly with average chrome, emblem and cracked lens.

Reproduction ribbed aluminum foil backing plate for the gas doors on the 1969 and 1970 Mercury Cougar and XR7 models.

Good used fuel door framed insert, without the crest as shown. These in most cases will not include the thin foil backing plate as shown. "A" grade will have minor rust pitting and some dullness on the chrome, overall very good used.Foil backing plate available in reproduction, see related items.

Fair used fuel door framed insert, without the crest. These most often will not include the thin foil backing plate as shown. "B" grade will have some rust pitting and some dullness on the bright work, overall fair used. Foil inserts available used in limited quantities.

Restored fuel door framed insert without the background decal or crest, for the 1969 - 1970 Mercury Cougar. Foil backing plate available in reproduction. At the moment there are no reproductions on the walking cat, you can however polish up your old cat and re-use it in this frame.

New Old Stock gas door. Fits all 1969-70 Mercury Cougars. Ford part number C9WY-65405A26-A

Used gas door with hinge spring. The black painted door as shown in the picture is a service replacement fuel door. Used doors are bare steel and will come with the hinge and spring.  Ford part number C9WY-65405A26-A

This filter ONLY fits the following 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19.

This filter ONLY fits the following Ford Holley 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. This is a service replacement filter, it has D2AE-9155-AA stamped on the body of the filter. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19 and C9AZ-9155-B,  FG-39.

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

This is the steel tube that goes from the carburetor to the fuel pump. Designed to fit OEM Carter X fuel pump with screws holding two halves together. Modern Carter fuel pumps are crimped and will need some bending of this tube to fit. Please see item 11761 tube for use with generic Carter fuel pumps.

This is the steel tube that goes from the carburetor to the fuel pump on the 289 or 302 with the AutoLite 4300 4 barrel carberator. Original steel version.

This is the steel tube that goes from the carburetor to the fuel pump if you have a 289 or 302, and you have the Autolite 4300 4 Barrel Carburetor. Stainless Steel.

This is the steel tube that goes from the carburetor to the fuel pump. Available in original steel or stainless steel.

Reproduction STAINLESS STEEL Fuel Pump to Carburetor Fuel Line for the 351W And the 4 BBL for the 1968 -1970 Mercury Cougar

This is the original equipment steel tube that goes from the carburetor to the fuel pump.

Reproduction fuel line for the Boss 302 engine standard steel construction. Application would be Mercury Cougar Eliminator and Ford Mustang with engine code G or the 302 HO engines. Bent for use with factory intake manifolds, OEM Carter fuel pump, and OEM installed Holley carburetor. Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

Reproduction fuel line for the Boss 302 engine stainless steel construction. Application would be Mercury Cougar Eliminator and Ford Mustang with engine code G or the 302 HO engines. Bent for use with factory intake manifolds, OEM Carter fuel pump, and OEM installed Holley carburetor. Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

Reproduction fuel line for the Boss 429 engine standard steel construction. Application would be for all Ford and Mercury products with Z code Boss 429 engines. Bent for use with factory intake manifolds, OEM Carter fuel pump, and OEM installed Holley carburetor. Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

This is the steel tube that goes from the carburetor to the fuel pump. Designed for vehicles LO-VOL fuel pump, fits 67 - 70 Mustang, 67 Cougar 390, 67 Fairlane and Torino.

Reproduction OE steel two piece fuel tank to pump fuel lines with 3/8" fittings that runs down the rocker panel on the Mercury Cougar. *NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

Reproduction stainless steel two piece fuel tank to pump fuel line with 3/8" fittings that runs down the rocker panel on the Mercury Cougar. *NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

Reproduction fuel pump for all 1967-69 Mercury Cougars and Ford Mustangs equipped with either the 390-2V or 4V engines. Updated design from the originals, fuel lines fit the same.

Reproduction fuel pump for all 1967-69 Mercury Cougars and Ford Mustangs equipped with either the 427 or 428 engine. Updated design from the originals, fuel lines fit the same.

Reproduction gasket for the vintage two piece Carter fuel pump bowl for the Mercury Cougar or Ford Mustang equipped with either the 390-4V, 427-4V or 428CJ engine.

For use with your original Carter fuel pump on Cougars equipped with a BOSS 302, GT 390, 428 Cobra Jet or 429 Cobra Jet.

This is the single prong version fuel sending unit for 69 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original.Check out the video below on our new gauge tester: ...

This is the stainless steel, single prong version fuel sending unit for 69 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original. Check...

This is the stainless steel, single prong version fuel sending unit with 1/4"  return line for 69 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to...

New manufactured fuel / gas tank for 1969 Mercury Cougar and 1969 Ford Mustang, 20 gallon capacity, has drain plug. This is the economy version, which has a slightly different stamping, and is made in Taiwan.Replaces Ford part #C9ZZ-9002. *NOTE* Tank will fit into all 1967-68 cars, fuel filler necks must be adjusted to fit with this taller tank. Sending units ideally should be changed to the 1969 sending units. 1970 cars with California emissions will have to change filler necks entirely. ...

Original style wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Replaces Ford Part #: C5ZZ-8287-A.

Used original wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Ford Part #: C5ZZ-8287-A.

Reproduction fuel / gas tank for the Mercury Cougar or Ford Mustang. 20 Gallon capacity, very correct reproduction. Unit is designed to OE fit, form and function requirements accomplished by leveraging our OE fuel system design expertiseMade with corrosion resistant Ni Terne steel for durabilityUnit is leak tested after production to ensure product in free from fuel and / or evaporative leaksEach new fuel tank is road tested to ensure real world performance and to verify that each design...

New manufactured stainless steel fuel / gas tank for 1969 Mercury Cougar and 1969 Ford Mustang, 20 gallon capacity, has drain plug. Replaces Ford part #C9ZZ-9002. *NOTE* Tank will fit into all 1967-68 cars, fuel filler necks must be adjusted to fit with this taller tank. Sending units ideally should be changed to the 1969 sending units. 1970 cars with California emissions will have to change filler necks entirely.

If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970. Replaces Ford part # C9AZ-9H576-A.

This is our reproduction, uncut, driver side (left hand), long, front and rear floor pan for your Mercury Cougar convertible.

This is our reproduction, uncut, passenger side (right hand), long, front and rear floor pan for your Mercury Cougar convertible.

Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...

Reproduction full length passenger side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years.

C8OZ-14A187-A Unique 1/4"-20 bolt for attaching the fuse blocks. 69 70 71 72 73 Mercury Cougar Ford Mustang fuse panel attaching bolt. Includes "C" clip and spring as shown. "C" clip keeps the bolt in the black fuse block.