Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Used single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. Sold individually, Ford part number 57487-S.
Ford part # for the nut is 33772-S4, for the bolt 370301-S8, and the flat washer 358994-S.Slight changes in the hardware between the start of 1969 and the end of 1970. We see a slight difference in the height of the nut. Hard to tell unless side by side.
Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually.
Bolts and installation kit for most 1969 Mercury Cougar and Ford anything, including Mustang with 351W engines. Kit includes main pivot bolt and 4 mounting / adjusting bolts as shown. Spacer not included, but available used. Quality AMK kit F-1307.
Bolt and nut for the clamping the coil into the coil bracket as found in 1967-73 Mercury Cougar and Ford Mustang. Fits all of the various coil brackets used 1967-73 on most all Ford engines. This is a 8-32x1-1/2, 1/4 hex headed fine thread bolt and nut. This is not the round headed slotted screw type that Ford also used.
Bolt and nut for installation of disc brake pedals in any 1967-73 Mercury Cougar or Ford Mustang. See related items for plastic bushings and metal spacer.
Bolt kit for installing front sway bar clamps to the body for any 1969-73 Mercury Cougar or Ford Mustang. 5/16" bolts for 1969-73 cars. Starting in 1969, the bolt size was changed from 3/8" to 5/16". We stock the 3/8" bolt kits, which was standard for 1967-68 cars. See related items.
Bolt kit for installing the idler and adjusting pulley on any 1968-69 Mercury Cougar / 1968-69 Ford Mustang or 1968-69 Ford / Mercury with small block 289 / 302 / 351W engines. 4 bolts 3/8-16x7/8 inch washer head bolts.
Bolt kit for installing the idler and adjusting pulley on any 1968-70 Mercury Cougar / 1968-70 Ford Mustang or 1968-70 Ford / Mercury with 390, 428CJ engines. 4 bolts 3/8-16x7/8 inch washer head bolts and 2 thick 3/8 washers.
Kit comes complete with J bolts and mounting nuts. Replaces Ford Part #: D0AZ-10756-K.
Manual transmission clutch bolt kit for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions any engines. Quality AMK bolt kit F-3263.
AMK fastener kit for attaching manual transmission clutch Z-bar brackets. 1969-70 Mercury Cougar and Ford Mustang with 302 or 351 engines. AMK number F-474.
AMK fastener kit for attaching manual transmission clutch Z-bar brackets. 1969-70 Mercury Cougar and Ford Mustang with 390 or 428CJ engines. AMK number F-473.
Correct leaf spring eye bushing bolts for the 1968 - 1973 Mercury Cougar. 5" in length. Set includes 2 bolts and 2 nuts. Replaces Ford Part #: C7ZZ-5781-A.
Pair of bolts for installing the fuel pump on most V-8 engines. 289, 302, 351W, 390, 427-4V, and 428CJ. AMK bolts 3/8-16 x 1-1/2 inches. Sold as a pair, for installation of mechanical fuel pump into the timing covers. AMK F-519. 43530-S8.
AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to any automatic transmission on all 1967-69 Mercury Cougar and Ford Mustang with 289, 302, 351W, 351C, 390, 428CJ engines. AMK number F-176.
AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to top loader transmission on all 1967-69 Mercury Cougar and Ford Mustang with 289, 302, 351W, and 351c engines. AMK number F-1414.
AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to top loader transmission on all 1967-69 Mercury Cougar and Ford Mustang with 390 or 428CJ engines. AMK number F-1741.
Reproduction oil pan bolt kit for the Mercury Cougar or Ford Mustang equipped with the 289, 302, or 351W engine.
Oil pan bolt kit for all FE 390, 427, and 428 engines. Set is made by AMK and includes 20 OEM style bolts and washers. We sell them specifically for 1967-70 Mercury Cougar and Ford Mustang, but they will fit most all Ford "FE" engines including 352, 410, and 360 Ford engines. If you happen to have a 428CJ with windage tray, we also offer a set of bolts for that application too. ...
Oil pan bolt kit for all 428 Cobra Jet and 428 Super Cobra Jet engines with windage tray. Set is made by AMK and includes 20 OEM style bolts and washers.
Fits 1967 - 1973 Standard or XR7
Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.
Correct head-stamp.
This is the Water Pump Bolt Kit for 1969 Mercury Cougar and 1969 Ford Mustang with the 302 or 351W engines with air conditioning. Quality kit by AMK Products - F-308. This kit comes with an instruction sheet, and shows the correct placement of the bolts.
This is the Water Pump Bolt Kit for 1969 Mercury Cougar and 1969 Ford Mustang with the 302, Boss 302, or 351W engines without air conditioning. Quality kit by AMK Products - F-307. This kit comes with an instruction sheet, and shows the correct placement of the bolts.
New Bolt kit, for the installation of a water pump on any Ford 352, 390, or 428CJ engine. Fits all 1967-70 Mercury Cougar and Ford Mustang with 390-4V, 390-2V, and 428 Cobra Jet engines.
Set of 16 bolts for the intake manifold on any factory 1969-70 Ford 351W-2V and 351W-4V engine. AMK F-1131.*Note - Excludes all 351 Cleveland engines.
Set of 12 bolts / spacers / stud for the intake manifold on any factory 1969-70 Ford S code 390-4V or 428 Cobra Jet or 428SCJ engine. AMK F-475.*Note - Excludes 1967-68 390 engines.
Correct leaf spring eye bushing bolts for the 1967 Mercury Cougar. 6.5" in length. Set includes 2 bolts and 2 nuts. Replaces Ford Part #: C5ZZ-5781-A.
14 piece bolt and screw set used to attach the convertible tack strip to the body. Kit comes with (12) 7/16 bolts and (2) phillips head screws.
New valve cover bolts for all 289-2V, 289-4V, 302-2V, 302-4V, and 351W-2V, and 351W-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 12.*Note - Excludes Boss 302 and 351C engines (see part number 8317)Replaces Ford part number 373071-S.
Reproduction valve cover bolts for all 390 / 427 / 428 Ford engines.
Reproduction black Allen head valve cover bolts. The bolts a re a bit longer to accommodate for the extra spacing required on the aluminum finned valve covers.
Reproduction stainless Allen head valve cover bolts. The bolts a re a bit longer to accommodate for the extra spacing required on the aluminum finned valve covers.
Reproduction set of four 2 3/4" black phosphate bolts for the 2 1/4" fan spacer on the 67 - 73 Cougar or Mustang.
Cylinder head bolt set for any 1967-70 Ford 390 or 428CJ engine. 10 short and 10 long, Grade 8 cylinder head bolts. Proper lengths for Ford FE engines. See related items for individual long or short cylinder head bolts.
Reproduction bolts and washers for the C-6 automatic bell housing on any 1967-70 Cougar or Mustang equipped with a 390 / 428 engines and code U automatic transmissions. Bell housing to engine block bolts. Fits most all other Ford big block V-8's from 1966-70.
Reproduction bolts and washers for the manual transmission bell housing on any 1969 - 73 Cougar or Mustang equipped with a 302 / 351 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1969-73.
Reproduction bolts and washers for the manual transmission bell housing on any 67 - until 2/1968 Cougar or Mustang equipped with a 390 / 428.
Reproduction bolts and washers for the manual transmission bell housing on mid , like Feb 1968 - 1970 Cougar or Mustang or other Ford car equipped with a 390 / 428 engines. Bell housing to engine block bolts.
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold as a set of 4. Concours phosphate & Oil (gray-black).
Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang, radiator fan clutch to radiator cooling fan. 1/2 inch hex head size. Threads are 5/16-18. Four bolts with captured split washers. Also sold individually. ...
Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. 1/2 inch hex head size. Threads are 5/16-24. Also sold individually. These bolts have an approximate length of 7/8" to the shoulder and an approximate overall length of 1-1/8". ...
New set of bolts for fastening the transmission inspection cover on all 1967-70 Mercury Cougar, Ford Mustang, and Ford anything with 390, 428CJ, and 352 or any FE style Ford engine. Includes 3 and 4 speed transmissions.
Pair (2) Bolts for securing the inspection cover for any C-4 automatic transmission 1967-68 Mercury Cougar or 1965-70 Ford Mustang. Additionally also fits FMX transmissions 1969-73 Mercury Cougar.or Ford Mustang.
4 Bolts for securing the inspection cover for any C-6 automatic transmission 1967-70 Mercury Cougar or Ford Mustang.
Reproduction bolts for the deck/trunk lid latch for the Mercury Cougar or Ford Mustang. This is a set of five bolts and will fit both the standard and XR7. Total of 5 bolts used 1969-73, 1967-68 Cougars will only use 2. We think that Mustangs use 5 on all years 1967-73.AMK F-227 ...