1969 Mercury Cougar

Complete grade B bezel for the standard or decor level interior for both the 1970 and 1969 Mercury Cougar. Grade B bezels will have faded woodgrain and slightly bent edges. Includes a metal "COUGAR" emblem.

Complete very nice bezel for the Standard or Decor level interior for both the 1970 and 1969 Mercury Cougar. Includes a plastic "COUGAR" emblem.

Grade "A" panel with no blemishes, ready to install on your show car. This listing does not include emblem or the aluminum surround.

This actually is a pretty impressive part once installed if your expectations are not overly high. It fits snug (very tight) over your existing cracked dash and you affix it by putting silicone around the perimeter. Once in place the obvious indicators of it not being original are the lack of simulated stitching on the leading edge and the larger perforations for the center speaker. The good thing about this unit is that your dash pad can have large chunks missing and it still will work! You...

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang with factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade B used some pitting and or  extra holes. Replaces Ford part number C9ZZ-6504320-D.

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang without factory air conditioning, this panel does not have the round holes in the outer section. This is not a reproduced part, only the 'with' A/C panel is reproduced. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade A used, no pitting, no...

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang without factory air conditioning, this panel does not have the round holes in the outer section. This is not a reproduced part, only the 'with' A/C panel is reproduced. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade B used, may have...

Used wire set for the dash plug from the main under dash wiring harness from 69 - 70 Cougar or Mustang. Wire colors may vary. NOTE: When ordering, make sure to leave comment on whether you have a Standard or XR7

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

This plate allows you to install (2) 3 1/2" speakers of your choice in place of the (1) original factory speaker in the dash of your Cougar or Mustang. This is the same plate used on the Kenwood and Pioneer Dual Dash Speaker kits. Check out this video

Features two 4 ohm 3 1/2" coaxial two way speakers. Huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with or without in-dash factory AC. In Non-A/C cars, this speaker may partially crush the vent duct tube. Check out this video

A/C compressor clutch decal for Mercury Cougar and Ford Mustang.Replaces Ford Part #: C7AA-2987-D.

This is a reproduction of the original engine displacement decal. Black on chrome background followed by black background with chrome Cougar logo and 351-2V in chrome. Located on the top of the air cleaner.Fits the following models with a 351 2 barrel engine: 1969 Cougar1970 Cougar 1969 Mustang1970 Mustang

This is a reproduction of the original engine displacement decal. Black on chrome background followed by black background with Cougar logo and 351-4V in chrome. located on the top of the air cleaner.Fits the following models with a 351 4 barrel engine: 1969 Cougar

This is a reproduction of the original engine displacement decal with a gold background with the black lettering followed by the Mercury head logo and 390-4V in white with a black background. located on the top of the air cleaner.Fits the following models with a 390 4 barrel engine:1969 Cougar

This is a reproduction of the original Autolite parts decal that was located on the air cleaner.Fits the following models with a 428 Ram Air engine:1969 Cougar1969 Mustang

This is a reproduction of the original black engine displacement decal with gold lettering and black and chrome checkerboard on each end that was located on the top of the air cleaner.Fits the following models with a 428 4 barrel Cobra Jet engine:1969 Cougar1970 Cougar

This is a reproduction of the original Autolite parts decal that was located on the air cleaner.Fits the following models with a BOSS 302 engine:1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang ...

This is a reproduction of the original decal that contains the word "FRONT" that was located on the front of the air cleaner.Fits the following models 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang ...

This is a reproduction of the original service instruction decal that was located on the side of the air cleaner.Fits the following models:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Ignition coil silver decal stamped with:FAC-12029-A12 VOLTS AUTOLITE OLECUSE WITH EXTERNAL RESISTOR

Reproduction decal detailing the original instructions from the Ford Motor Company.

Nice reproduction that is "almost" spot on. Of the two versions available this one has much more definition. When you put an original next to this reproduction you will notice the original has a more raised, defined face on the Mercury Man.

Reproduction 390 4V GT Emission Decal for the 1968 and 1969 Mercury Cougar / Ford Mustang

Controversy abounds on which shrouds received these and which did not. It is our understanding that no early Cougars came from the factory with this decal installed. This decal first surfaced when Ford had major problems with their flex fans in the early 1970's. We will let you decide if it is correct for your application... This is placed on the top, center of the fan shroud.

Reproduction Detroit Locker Glove Box Decal for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar

Notice the line drawing of a Mustang and the decal has a Cougar part number. More times than not I see the exact decal with a Mustang part number for 1969. Replaces Ford Part #: C9WB-17093-D.

These are our 2-inch diameter round decals to customize the plastic Legendary Wheel Co. center caps that come with their wheels. These caps are also available separately, see item # 30529. Nice quality vinyl that will last outdoors, and the graphics have a mirror finish to compliment the chrome. *If you're buying a set of Legendary Wheels from us, mention this item in the notes and we'll include them for free! ...

New "Mercury" script decal in black for any Mercury, but will be at home on the Cougar. Measures 10 3/4" wide by 1 1/2" tall.This is a die-cut vinyl decal. To install, you'll have to peel off the backing, apply the decal to the intended clean surface, press in place with a plastic squeegee or credit card, then carefully peel away the top contact paper.

Reproduction oil cap decal for the Ford 1965-67 oil caps. 

Located on the bottom side of trunk lid.

This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these.  Sold Individually Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...

Located on either the left or right hand shock tower. On rare occasion we also have seen these above the washer bottle on the 69-70 models. Replaces Ford Part #: C7AE-6C029-A.

Replacement sleeve to put onto your original tire inflator bottle. Correct style for 1969-70 Mercury Cougar and Ford Mustang. Specifically for the 7.35-14 space saver tire installed optionally in Cougars and Mustangs. Correct Ford part number C9WA-19F514-A imprinted on the decal as shown.

Here's a good replacement for those old worn out aluminum "stereo" decal inserts for your 69 - 70 door speaker grills. Keep in mind that these are just simple decal stickers and are not made from aluminum as the originals were. We do offer used aluminum decals here.SOLD INDIVIDUALLY. ...

Tire pressure / tire size / maximum load decal for the 1969 Mercury Cougar equipped with the 302, 351, 390 or 428 engine. Printed with Ford Part # C9WA-1532-B.

Used until early 1970 when vehicle was equipt with AC. Decal Text: Autolite Regulator C8TF-10316-A NEG

This walking cat decal measures 10.5" x 3.65".

This walking cat decal measures 10.5" x 3.65". Check out this video

This walking cat decal measures 10.5" x 3.65".

This walking cat decal measures 10.5" x 3.65". Check out this video

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Pictured below is Robin Miller's "G-Force" Cat! Click on images to enlarge. Check out this video of our 2013 Open House event! ...

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Check out this video

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog.Check out this video of our 2013 Open House event. See you next year! ...

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog. Shown in Black.Check out our video f the 2013 Open House event. See you next year! ...

These decals are really impressive quality. They stick on really nicely, have super grip and a nice glossy finish. You can use them to make up your own signs, decorate your shop wall, trailer, or make up that car show easel/sign that you have been needing. Available only in left facing (traditional pose). Check out this video of our 2013 Open House event. See you next year! ...

Rare, almost impossible to come by collectors item designed to adhere to the inside of your window. Original water transfer 3" diameter Cougar logo decal. Soak in water for 30 seconds and slide onto glass. I have only seen these dealer "give aways" one other time in all my years of collecting. We want to you to keep in mind that the cloudy areas you see on the decal in the picture are nothing more than paper residue, and will easily wipe off. Check out this video ...

Replaces Ford part #C8AZ-6223362-A. Sold in pairs, four required per car, used on most Ford products. We often get calls like "How do I remove my front window cranks?" Unlike the rear cranks that are held on by an Allen set screw, the fronts have a Phillips screw under this decal. If you are careful, often you can reuse your original and glue it back in place.