1969 Mercury Cougar

[No Description Provided]

Replaces Ford Part # 381985-S Sold individually

Bumper bolt nuts sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as not to...

Self threading speed nut for attaching "COUGAR' scrip emblems to the rear quarter panel of any 68 - 70 Mercury Cougar. Sold individually, 4 needed per emblem. Whereas these work fine, the originals were an acorn style nut and look very different.

383278-S 1/4-20 Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs. This is a new or reproduction part from AMK.

383278-S Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs.

Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.

Reproduction nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. Replaces Ford part number C9ZZ-11650-A .

Nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. These are used, and usually will have small blemishes. All will have good threads and chrome plating on the face.Ford part number C9ZZ-11650-A .

Reproduction exterior convertible boot moulding / trim nuts for the Mercury Cougar or Ford Mustang and Torino. Here's another great reproduction brought to you by WCCC! Each vehicle will require 20 nuts. Sold individually.

Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. Sold individually.Replaces Ford part # 373556-S.

Replaces Ford part # C2DZ-6A529 Sold Individually.

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut. 

New 3/8-16 nut for the shock tower shock cap. Three nuts used on each cap, 6 total per car. Sold individually.Replaces Ford part number 377706-S7.

Perfect fit.

Correct nut that is designed not to come undone.

These were used to attach the taillight assembly to the tail panel on a 1969-70 Cougar. Five were used per taillight, 10 required in all for one car. Sold individually. Also the same size for 1967-68 tail lights.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...

New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S

Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.

Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS service replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.

Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item C7AZ-9B471-A, AND D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.

380771-S100 Good original used nut and washer for mounting all pitman arms. Has correct 7/8"-14 threads. Ford master part number for the washer is 34814-S.

Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

Nuts and washers for attaching the rear differential carrier or pumpkin or third member to the rear axle housing. Correct for all 1969-73 Mercury Cougar and 1969-73 Ford Mustang. 8 inch or 9 inch third members, all the same.

Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.

Reproduction heater duct nylon rivet #375064-S is sold individually.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.

Reproduction black oil cap for your 67 - 70 Cougar or Mustang, featuring the FoMoCo logo.

Correct detail. Chrome plated with rectangle-style FoMoCo script stamped into the top surface of cap. Nipple measures 5/8" diameter. This is the correct Closed Emissions oil cap for the finned "G" valve covers we sell.

Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.

This cap is an exact reproduction of the original. Features include three filters and the AUTOLITE logo. The PCV elbow is included but not installed for those wanting to re-use their original metal elbow or the metal concours reproduction. Fits the 67, 68, 69, and 70 Mercury Cougar. Technically, this is a copy of the Ford service replacement oil cap, and the same cap with plastic elbow as found on cars starting in 1969. 1968 Ford cars sold in the US, had metal elbows. ...

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

Chromed "Autolite" oil filler cap, original cap chromed, not reproduction. Bare cap, will need baffle material added. Also recommend purchase of a rubber grommet and either plastic or steel PCV elbow. Your specific application will determine if plastic or steel elbow. See related items. C8AZ-6766-B$40 refundable core charge does apply.

Original used oil filler cap adapter for any 1967 Mercury Cougar or 1965-67 Ford Mustang. This is for use with the open emissions, push on oil cap. This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D. Will most definitely need a new gasket. These will ship "as found" or fresh from our wrecking yard. Photo is most cases will show a cleaned part for glamour photography shots. Also have reproduction version.Ford part...

This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D.

This cap is an exact reproduction of the original. Features include three filters, the AUTOLITE logo and a beautiful chrome finish. The PCV elbow is included but not installed for those wanting to re-use their original metal elbow or the metal ( concours reproduction). Fits the 67, 68, 69, and 70 Mercury Cougar. Available in Black or Chrome Finish.Technically, this is a copy of the Ford service replacement oil cap, and the same cap with plastic elbow as found on cars starting in 1969. 1968...

Engine oil dipstick as found on most any 1969 Ford with 351 Windsor engines (H or M Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of shield to dip stick end is approximately 22.80 inches. The handles were painted blue originally. Ford part # C9OZ-6750-A, Ford casting # C9OE-6750-B.

Chromed engine oil dipstick as found on many 1967-69 Ford with 390 engines (S Code), 427-4V (W Code), 428CJ (Q or R Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dipstick end varys at either 19.25" and approximately 20.25" (full, add, and safe marks are the same). The handles were chromed originally. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

Painted engine oil dipstick as found on many 1967-69 Ford with 390 engines (S or X Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. From the top of the shield to the dipstick end varys from either 19.25" to approximately 20.25" (full, add, and safe marks are the same). The handles were painted blue originally. Typically the painted dipsticks were found on the non-GT (6.5 Litre) cars in 1968. Ford part # C7AZ-6750-A, Ford casting...

Small block dipstick tube for the 1968 Cougar and Mustang. Painted blue as original. Replaces Ford Part # : C8AZ-6754-A. Also fits 1969 Mustangs with the 302.

Also available in Chrome. We recommend going with a good used tube because these reproductions just don't fit. Here's what we found out:The original dipstick tube measures .362The one we sell with paint on it measures .375With the paint Stripped, it measures .365It will not fit in correctly even after attempting to smack it in with a mallet with the paint stripped off. Replaces Ford part # C7OZ-6754-A.

Nice chrome finish. Also available in Ford blue. We recommend going with a good used tube because these reproductions just don't fit. Here's what we found out:The original dipstick tube measures .362The one we sell with paint on it measures .375 With the paint Stripped, it measures .365 It will not fit in correctly even after attempting to smack it in with a mallet with the paint stripped off. Replaces Ford part # C7OZ-6754-A. ...

Quality After-Market oil filter for the 1967 - 1973 V-8 Mercury Cougar or Ford Mustang. Better filter than OEM.