1969 Mercury Cougar

Reproduction walking cat center emblem for the 69 Cougar rim blow steering wheel.

Good used center with no cracks and an average amount of fade most noticeable in the red portion of the emblem. Many of these emblems are broken or missing because people think this is the horn button and if they just push harder the horn will sound!

Reproduction center emblem for the 69 Cougar rim blow steering wheel.

Reproduction silver walking cat emblem / insert for the 70 Eliminator T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 69 - 70 Eliminator, this handle will fit on any 67 - 73 Cougar with the automatic transmission.

This small sized Cougar emblem (1 3/8" long) was used on 1969 - 1973 Cougars without AC. It was affixed to a block off plate in the very venter of the dash by two peened over die cast studs. It will glue back in place nicely and many Cougar fans have found fun "custom" applications for this attractive piece. This emblem will not be pitted or scratched in any way.

Since our restored emblems look so good we have a hard time selling NOS these days which works out just fine as we only seem to be able to obtain 1 of these every few years. Keep in mind your used cores have trade in value against this NOS part. Casting number seen on back side for the assembly is C9WB-65517A56-A and black plastic is C9WB-65517C00-A, Casting number on chrome is C9WB-65517A20-A

This vinyl piece glues to the center of your block off plated on Cougars not equipped with AC. These often times have shrunk slightly over time. We cannot guarantee to always have all the colors in stock. Call for color availability or put desired color into the comments section of your order.

Restored emblem / insert for the 69 Cougar center grille. These are sold on an exchange basis, so you must have a good core with both studs intact. The emblem will be without the decal in the center. You can get it here. Ford casting number reads C9WB-8B369-A NOTE! If you pay the core charge on our 1969 restored grille parts or complete grilles we will be under the assumption you do not have cores to send in or they are average quality with pits and cracks. If you have really clean cores you...

Good used emblem with both studs intact, no obvious pitting or scratches. This item will have a faded center decal, and you will need a new decal. You can either add a note to the order asking that we contact you about upgrading to an emblem with less fade for a upcharge, or get a reproduction decal here. Ford casting number reads C9WB-8B369-A ...

Restored corral for the passenger side eyelid on the 1969 Mercury Cougar. This is just the outer corral and does not include the background decal or the walking cat emblem. NOTE! If you pay the core charge on our 1969 restored grille parts or complete grilles we will be under the assumption you do not have cores to send in or they are average quality with pits and cracks. If you have really clean cores you will want to send them in advance and not pay the core charge so we can do what we call...

This reproduction driver side (left hand) emergency / parking brake cable fits from the equalizer to rear brakes. 1 required per vehicle. The cable length is approximately 29-1/2". Cougars manufactured after 2/69 may use the 1970-73 left hand cable. It is easy to check by measuring the cable. The 1968 cable is just over 29" long, and the 70 cable is just over 32" long. Click on the image to left to see the difference. The 1968 style of emergency brake cables can be used on the 1967 cars, as...

Reproduction emergency / parking brake cable return spring that goes underneath the car for the Mercury Cougar or Ford Mustang.

Complete reproduction emergency / parking brake assembly for the 1969 Mercury Cougar or Ford Mustang. The 1969 model used a T shaped chrome release handle and 1970 used a black plastic T shaped release knob. This version has the chrome handle. There is not a plastic T handle reproduction available. Replaces Ford part # C9ZZ-2780-A.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for LH or DRIVERS side original part Ford number is C9ZZ-2A638-A.

Used parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for LH or driver side is C9ZZ-2A638-A. This unit is from a solid Western parts car, so you won't be getting one of those rusty East Coast units! Ford part # C9ZZ-2A638-A.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for RH or passenger side original part Ford number is C9ZZ-2A637-A.

C9ZZ-2A637-A Parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for RH or passenger side is C9ZZ-2A637-A. Clean Western part with no heavy corrosion like you see on Eastern cars.

Reproduction 10" parking brake link. Spring included. Sold individually, two per car. Replaces part Ford Number C2OZ-2A642-A

Parking brake link. The spring (not included) is wound in a rectangular shape to fit the one end of the link. Ford part # C2OZ-2A642-A.

New emergency flasher can for all 1969-73 Mercury Cougars. Not to be confused with the turn signal flasher canister, those are rated differently. 

Used emergency flasher for the 1969 Mercury Cougar. This flasher either came in gold or silver. Ford Part number C9WB-13350-B1 or C9WB-13350-B2

Used Emergency Flasher Knob Bezel / Fixed Column for the 1967 - 1969 Mercury Cougar / 1967 - 1969 Ford Mustang 

This two part black box is what encapsulates your sequential unit for all years 1969-1973. This of course will work with our reproduction sequential unit as well. This box was designed hang from a hook that is welded to the trunk floor just behind the driver side wheel well. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Angled bracket for mounting the steel dash panel to the cowl. Two brackets per car, sold individually. These are the end mounting brackets for all 1969-70 Mercury Cougar and Ford Mustangs with or with air condtioning. Ford part number C9ZB-5404366.

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7M27, December 27, 1967.  Used 0.030 over bore 4.080" Ford 390 engine block. Years ago, it looks to have been fresh machined, with new freeze plugs. No paperwork, bare block. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date...

These Big Block motor mounts bolt to your engine block on the top side and to the motor mount (insulator) on the bottom side. These are very correct looking and fitting reproductions, much better than the $95 version you will find in most catalogs. Fits 1967-70 Mercury Cougar and Ford Mustang with 390 or 428CJ engines, will fit passenger side of 427 side oiler engine, driver side will work with modification. Original Ford part numbers C7ZZ-6046-A R.H., C7ZZ-6046-B L.H. 427 number for the left...

New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury  switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

After-market exact reproduction of the original Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a gravity switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

Used engine lift hook or hoist bracket for all 1969-70 351W engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. H code 351W-2V and M code 351W-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We also sell...

Used engine lift hook or hoist bracket for all 1968-69 390 engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. X code 390-2V, S code 390-4V, and W code 427-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We...

Assembly line used engine lift hook. Driver side 1969-70 with 428 Cobra Jet engines, including 428SCJ. Stamped with number C8OE-17K004-B, which is the second version. An earlier version was used on 1968 R code cars. Fits all 1969-70 Ford cars with either R code or Q code 428 engines. Cougar, Mustang, Cyclone, Torino, Talledega, Cobra, Fairlane, Montego, Ranchero etc. Attaches to the driver side exhaust manifold. There is also a passenger side engine lift hook, see related items.  ...

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Left hand bracket. Ford part number D0ZZ-6029-D. The original 1967 part number for this bracket was C7ZZ-6029-B.

Mount to the frame for supporting and mounting the FE 390, 427, and 428CJ engines. Also known as lower engine mounting brackets. For all 1967 - 1970 Cougars with 390 - 427 - 428 engines. Also includes 1967 with 289. Sold in sets. Includes one each: D0ZZ-6028-D & D0ZZ-6029-D engine frame brackets.

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Right hand bracket. Ford part number D0ZZ-6028-D. The original 1968 part number for this bracket was C8ZZ-6028-B.

Reproduction pair of engine pedestals / frame brackets for the 67 - 70 big block V-8’s. Mounts to the frame for supporting and mounting the big block 390, 427 and 428 engines. Also known as lower engine mounting brackets. Sold as a pair.

Factory original part for all 1968 - 1970 Cougar hardtops (non-convertible) with 289, 302, and 351 engines. Left hand bracket. Ford part number D0ZZ-6029-C.

Reproduction pair of engine pedestals / frame brackets for the 68 - 70 small block V-8’s. Mounts to the frame for supporting and mounting the small block 289, 302, 351 engines. Also known as lower engine mounting brackets. We recommend this bracket for 1967 Cougars with 289. Sold in sets. *Converting to these mounts on 1967 Cougars with 289 or 1969 – 1970 convertibles with 351 allows the use of reproduction engine mounts.

Factory stock for 1968 – 1970 small block V-8’s. Mounts to the frame for supporting and mounting the small block 289, 302, 351 engines. Also known as lower engine mounting brackets. We recommend this bracket for 1967 Cougars with 289. Sold in sets. Includes one each: D0ZZ-6028-C & D0ZZ-6029-C engine frame brackets. These are better quality and fit than the reproductions. *Converting to these mounts on 1967 Cougars with 289 or 1969 – 1970 convertibles with 351 allows the use of reproduction...

Factory original part for all 1968 - 1970 Cougar hardtops (non-convertible) with 289, 302, and 351 engines. Right hand bracket. Ford part number D0ZZ-6028-C.

[No Description Provided]

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1969 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1969 Cougar and Mustang with the 390 engine. We also sell this H pipe in a 2 inch diameter and have OEM style dual exhaust systems that include the H pipe,...

C9OE-9431-B 351W factory original cast iron exhaust manifold for driver side. For all 1969 and 1970 Windsor 351's.

C6OE-9428-A 390-4V factory original cast iron exhaust manifold for passenger side. 1969 390-4V IP only. Same as earlier versions, but with a 1969 date and chamfered opening for donut. No spacer needed.

C8OE-9430-D 428 Cobra Jet factory original cast iron exhaust manifold for passenger side. *Spacer required for installation.

Exhaust Manifold Choke Stove Rebuild Kit for All Small Block and Big Block Engines 1967 - 1973. Includes Stainless Steel Mesh Filter Element and Choke Stove End Cap Fitting.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.