1969 Mercury Cougar

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

These new taillight mounting washers are sold individually for your Mercury Cougar. Normally installed with a dollop of black goo for sealing out moisture. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-A. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-J. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8OE-D. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

Cast Iron Water Pump for the 1967, 1968 and 1969 small block. Has six vanes on the impeller. Includes Gasket. Several other websites state that there was a mid-year change in 1969 Cougar's with a 351W, but all the documentation we have and the cars we have on hand all indicate that this change took place at the very beginning of the 70 production year so that the 351C and 351W would use the same water pump. Replaces Ford Part #: D3UZ-8501-A or C5OZ-8501. ...

Light duty OEM Replacement cast iron water pump for any Ford FE 390 / 427 / or 428CJ. Gaskets included. No Core required Replaces Ford Part #: C8AZ-8501-A.

0D13  April 13, 1970 dated.  Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C9AE-8505-A. Found on many Ford 390 and 428CJ engines from 1969-70. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

Wave locking washers for the door hinges on the 67 - 70 Cougar or Mustang. These washers have teeth that will dig in and hold tight, making sure your door hinges never come loose.

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

This concours correct reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This Daniel Carpenter manufactured unit is made of slightly less dense material than the Midland unit, .75lb as compared to .85lb. If correctness is not an issue for you, you can get the Midland unit here. We have included a few comparison pictures so...

This offshore reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This overseas reproduction sold by Daniel Carpenter is simply another option to the US made version, and has been known to fit better than the US made weatherstrips. If correctness is not an issue for you, you can get the Midland unit...

Reproduction door glass to roof weatherstripping for the Mercury Cougar and Ford mustang. These units are sold as a pair and are also known as the roof rail weatherstrip. Replaces Ford part # C9ZZ-6551222. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Rubber quarter window to door glass seal. Passenger side 1969 Mercury Cougar and convertible, and 1969 Mustang hardtop coupe and convertible. Ford part # C9ZZ-65214A14-A. *NOTE* Will not fit Mustang fastback or Mach 1. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Correct for Coupe and Convertible, Mustang and Cougar. This vertical weather strip slides into the stainless steel strip that attaches to the back side of your left hand door glass. These cost a couple of dollars more than some you will see but are substantially better fitting than the budget version. Replaces Ford part # C9ZZ-65214A15-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video...

Correct for Coupe and Convertible, Mustang and Cougar. This vertical weather strip slides into the stainless steel strip that attaches to the back side of your right hand door glass. These cost a couple of dollars more than some you will see but are substantially better fitting than the budget version. Replaces Ford part # C9ZZ-65214A14-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video...

You will need new window gaskets if you plan on changing the headliner. Replaces Ford part #: C9WY-6542084. Installing it yourself? bedding compound is required for a complete seal.Here are some useful tips on installing this seal made by DCMR.From KTL Restorations; Our cure for installing this less than perfect fitting reproduction is to use the longer trim clips (black ones). The clips Ford used were red oxide and the reproduction clips are green. The black clips extend up about 3/32 of an...

This kit is easier to install than you may think! Five piece kit, comes with installation instructions. Be aware, the seals at the top of the glass do not line up perfectly leaving a gap on the quarter glass top seal. We are working on a solution.  Replaces Ford part # C9ZZ-7653986. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Reproduction driver side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Used driver side (left hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will have...

Reproduction passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Used passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will...

Sold individually, phosphate & Oil (gray-black).

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems. Specifically for installation of the new Legendary GT7 and 1966 Shelby wheels. Thread Size: 1/2" Bolt Pattern Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems for installation of the new Legendary aluminum wheels. These really only fit the Magstar style wheels; we recommend the 3/4" lug nuts for all the other Legendary wheels for clearance reasons. Conical Head: 13/16" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome lug nuts and 4 chrome valve stems for installation of the new aluminum Legendary Series wheels. Tapered for correct fit. This 3/4" size is what we recommend you use with the Legendary wheels, since the clearances are too tight for 13/16" nuts. Conical Head: 3/4" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

This hard to find cast aluminum spacer may be all you need to provide that little bit of extra clearance for calipers, control arms, frame rails, etc. At only 1/8" thick, it does not require longer wheel studs like many thicker spacers you find on the market.

New wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated 2" stud with correct 1/2 x 20 threads. These are slightly longer in length than the stock ones, this will allow the alloy wheels to fit the Classic Cougars.Replaces Ford part # C30Z-1107-A.*NOTE* You should use a press to remove and/or install the new studs.

This trim ring will fit any 14" 67 - 70 Cougar Styled Steel wheel even though the width originally varied from 1.75" in 67, to 2" in 68 - 70. This ring measures exactly 2" high and has the correct bevel like original. The hue is as bright as original and it is the polished version, not brushed like the 68 used. Good tight fit, best of the 4 different makes you will see advertised around the country. Unlike the originals, these do not self center very well. You can however adjust them into...

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator and 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, and most customers will be happy with our reproduction ring that is not brushed....

1969 and 1970 Cougar five spoke styled steel wheel trim ring. Master Part Catalog description: 15-7/8" Outer diameter, 11-15/16" Inner Diameter and 2" deep. This beauty ring will have slight blemishes that will not be very noticeable.  Note that the 1969 Eliminator was the exception and used the 1968 brushed finish trim ring. Ford part number C7ZZ-1210-A.

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator and 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, most customers will be happy with our reproduction ring that is not brushed. This...

1969 and 1970 Cougar five spoke styled steel wheel trim ring. Master Part Catalog description: 15-7/8" Outer diameter, 11-15/16" Inner Diameter and 2" deep. This beauty ring will have one or two very small scratches or dings that will not be very noticeable.  Note that the 1969 Eliminator was the exception and used the 1968 brushed finish trim ring. Ford part number C7ZZ-1210-A.

Reproduction aqua headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction dark blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction dark ivy gold / dark green headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...

Reproduction dark red headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction light blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction saddle headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Perfect fit, great reproduction. These plastic discs are found on all 69-70 convertibles on the rear of both decor and xr7 interior levels. We are unclear as to all the "exact" applications on all years and models but one application we have verified is the fronts of 1971 - 73 Cougars equipped with standard interior. The reason the standard interior 71-73 Cougars came with these is that the door panels were very thick on the 71-73 decor / XR7 models and quite thin on the standard models and...

This is actually not correct for a 1968 but it is all that is available in reproduction. The 1968 front is actually the same 4 1/4" length as the rear. Many people prefer the longer version as it makes it easier to roll up. We do have good used 1968 front cranks for those who prefer to stay with original. The portion that attaches to the splined shaft on the window regulator protrudes from the back 3/16" (as shown on the left in the comparison picture) and will not clear the 71-73 door panels...

We often will have B grade knobs with less than great chrome plating for lots less money. Plan on ordering new knobs, we have lots of colors to choose from.This is a good used original front window crank with no obvious scratches or pitting. It will be missing the decal that covers the screw sometimes it will have a knob, most often it will not. Ford part number is C8AZ-6223342-A, casting number on back reads C8AB-6223348-B or D0AB-6223348. *NOTE* This handle will work on a 1968 even though it...

C8AB-7630323-A Usually these will not have knobs. Plan on purchasing new knobs. Ask about our B grade knobs that will have some pitting or lusting issues. This is the correct "shorty" crank for a 1968 Cougar front window crank. It is the same length as the rear 1968 - 1970 but uses a center screw instead of a side Allen set screw. The 1969 - 1970 crank (with AM or no radio) looks the same but is longer. These shorter cranks were also used in conjunction with the factory door speakers used in...

This handle is a good replacement for the window cranks found on the 1971 - 1972 Cougar both front and back. The originals were 4 1/4" total length and this replacement handle is 4 7/8" long. The important detail on these is the fact that the female portion that attaches to the splined window regulator protrudes from the back 5/16". If you are using our chrome backing plates on your 69 -70, then this is the crank you will need to provide the correct clearance.Used before 10/71,...