1969 Mercury Cougar

Used XR7 grade "B" main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where grade "A" harnesses will be rare uncut beauties. 1969 Mercury Cougar XR7 models only. Not compatible with Standard model Cougar with AMPS warning...

This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels.Basic Ford part number 7631004

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels.Basic Ford part number 7631005

New old Stock rectangle side valve for the air cleaners on S code 390IP or 390-4V engines, Boss 302 Eliminator, Q code 428CJ engines all non-Ram Air. 1969-70 Mercury Cougar and Ford Mustang. NOS Ford, no Autolite or Motorcraft box. Ford Part Number C8OZ-9D612-C This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Reproduction rectangle side valve for the air cleaners on S code 390IP or 390-4V engines, Boss 302 Eliminator, Q code 428CJ engines all non-Ram Air. 1969-70 Mercury Cougar and Ford Mustang.  Replaces Ford Part Number C8OZ-9D612-C

This vacuum actuated door assembly was used on several performance motors without Ram Air. When extra air was needed under heavy acceleration the vacuum actuator opened the door on the side of the air cleaner base. The actuator on this unit needs to be rebuilt so this is considered a good core only.

Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is correct for all 1968 1969 and 1970 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy demand...

This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...

Used vacuum hose for the steering column release valve used in the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. Regular vacuum hose can be used to replace this hose if you are missing the original. However, it will not be correct. This nice original FoMoCo hose has the correct ribbing, stripes and comes with the firewall grommet. If you are missing this piece and you want your car to be right, this is a must have.

Reproduction Tilt Steering hose for the 69 Cougar or Mustang. Correct in every way, this reproduction is made to be an exact fit for your original hoses.

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

Good used, rust free valance. Getting to be hard to find without excessive filler or severe damage. We do have NOS and on occasion we we get in a flawless, never dinged, used example, this one will show a few very minor dings. Ford part # C9WY-17620-A.Fits:1969 Mercury Cougar1970 Mercury Cougar This is our latest (and youngest) new hire! This is JD Rush who was named in part after his Great Grandfather, Jack Donald Rush who got me (Don Rush) interested in old cars at a very young age. My...

Decent used, repairable valance. Getting to be hard to find without excessive filler or severe damage. If you would like pictures of the stock on hand email us as this is just an example of the part you get, not the actual part, damage varies as does price. We have repairable valances starting at $50.Ford part # C9WY-17620-A.Fits:1969 Mercury Cougar1970 Mercury Cougar This is our latest (and youngest) new hire! This is JD Rush who was named in part after his Great Grandfather, Jack Donald Rush...

We rarely have this one in stock. Keep in mind that when ordering multiple oversized items from us online that the shopping cart does not know how to best combine items to save you the most money, so we suggest choosing Manually Calculate as your shipping option at checkout so we can manually calculate shipping costs.  If you are ordering this item by itself, the quoted shipping cost should be accurate.Ford part # C9WY-17620-A.

Rare find these days! Keep in mind we are serious buyers of NOS Cougar parts. Keep in mind that when ordering multiple oversized items from us online that the shopping cart does not know how to best combine items to save you the most money. We suggest cutting and pasting your order into an email so we can manually calculate shipping costs.Ford part # C9WY-6540544-A.

C8OE-C-SR WCCC Carter service replacement anti backfire valve, but without the outer cover having the concours correct stampings.These units are used, not tested and one should assume they are non-functional.

Carter manufactured valve with C8TE-9B289-B and 4490-S imprinted on the valves' cover. Another hard to find part with correct date codes specific to Boss 302. Ford part number C8TZ-9B289-A. These units are used, not tested and one should assume they are non-functional. These units are used, not tested and one should assume they are non-functional. *Note, we try to carry later manufactured 'Service replacement' Carter anti backfire valves which are in every way the same, but...

This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.

Vacuum tested working hot water valve for any 1969-73 Mercury Cougars or Ford Mustang equipped with factory A/C. This valve stops the flow of warm coolant in the heater hose, when the A/C is on. Has the original cast brass valve and vacuum pod. Used but functional, the reproduction version is very good, but has a black plastic valve, like the service replacement valves from Ford.Replaces Ford part number C9AA-18495-D.

C9ZE-6583 Cast aluminum valve cover. Correct on 1969-1970 Mercury Cougar and Ford Mustang with 428CJ engines. This is the plain finned aluminum valve cover. Ford master part number C9ZZ-6582-B. Casting number can also be C9ZE-6583-B. Sometimes called 1969 Shelby valve covers. *Note - Some 1969-70 428 Super Cobra Jet engines came with a different style of  "Snake" finned aluminum valve covers.

SNAKECOVER Cast aluminum valve cover. Correct on some 1969-1970 Mercury Cougar, Ford Mustang, Shelby GT-500 with 428CJ and 428SCJ engines. This is the 'Snake' aluminum valve cover. Ford master part number C9ZZ-6582-B.

C9ZE-6583-G Cast aluminum valve cover with. Correct on 1969-1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engine. This is the finned aluminum valve cover. Ford master part number is C9ZZ-6582-C. *Note - Most, if not all 1969 Boss engines came with a chromed steel valve cover. Research did not turn a part number for that valve cover. Likely it is a chromed 351C valve cover. If you have the part number for the stamped steel chrome Boss 302 valve cover please share. ...

Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

CUSTOM ORDER, DROPSHIP ONLY. High quality reproduction vinyl top for the Mercury Cougar with sunroof that features both the correct pattern and finish. This top features a durable moisture resistant backing that will look good and last long.

This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...

Used seat belt bolt washer for the Mercury or Ford.

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

These used taillight mounting washers are sold individually for your Mercury Cougar. Two different inside diameters on these, we have them mixed, because they are in such short supply. Normally installed with a dollop of black goo for sealing out moisture. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems....

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Direct aluminum replacement for small block 1967 - 1969 cast iron pumps. Probably the last water pump you'll ever buy. Built to cool better and last longer than any other pump. Features state of the art high efficiency impeller with 16 veins and NASCAR roller type bearing. Race proven for reliability and performance. Includes Gasket. Several other websites state that there was a mid-year change in 1969 Cougar's with a 351W, but all the documentation we have and the cars we have on hand...

NOS weatherstrip for the driver side (left hand) quarter window in the Mercury Cougar or Ford Mustang. Ford part # C9ZZ-65214A15-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Includes all five pieces. Front bow rubber seal is C9ZZ-7653986-A. Side rubber seals are C9ZZ-7651564-A, C9ZZ-7651565-A. Much better fit than reproduction, perfect for that high end restoration.

Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. While you're in the trunk, you might also be replacing your trim. For some insight on the trim, check out our video below: ...

Used inner and outer driver side (left hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.*Customer Feedback*"I know Don Rush is a trusted and well...

Used inner and outer passenger side (right hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.*Customer Feedback*"I know Don Rush is a trusted and well...

New Dark Argent spray paint for the 69-70 Cougar or Mustang. This paint is designed for the 70 Mustang Mach 1 grille and rocker panels, but is a great match for the argent color on your Styled Steel Wheels.

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator, 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. WCCC is the only retailer offering these at present. Sold individually. Replaces Ford part number C8ZZ-1210-A. ...

Used on the optional 1968 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1968 Torino and Mustang. Also used on the 1969 Eliminator 12 hole wheel so as to match the brushed center cap. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, and most...

Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...

Reproduction white headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

NOS window crank knob, color is Aqua Blue, 1968 and 1969 only color. Fits 1968-69 Mercury Cougar and 1968 Ford Mustang and other Fords. Ford part number C8SZ-6523352-A1K.

Exceedingly hard to find in perfect used condition. Ford Part #:C9WY-6523209-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for...

Used drivers side or left door window regulator for all 1969-70 Mercury Cougar and Ford Mustangs with glued in door glass. Good used regulators that we inspect for operation. We suggest lubricating with suitable grease on all of the moving parts and the actual regulator mechanism during the installation. Comes complete with spring, white plastic rollers, and captured steel bushing with clip. The regulator used on the bolt in glass, which became standard soon after the 1970 model year began, is...