1969 Mercury Cougar

Set of 20 reproduction anti-rattle rubber gaskets for the stainless steel accent rings used on the styled steel wheels found on the Mercury Cougar or Cyclone. These units are used to keep the accent rings from rattling and driving Cougar and Cyclone owners insane. You can run your wheels without these rings, however Ford used them, so we sell'em. Set of 20

For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.

Reproduction antenna base gasket.Replaces Ford part #  C9WA-18298-B.

Here's a good original used antenna base gasket that is unique to the 1969-70 Mercury Cougar. Replaces part # C9WA-18298-B.

New carburetor gasket for most 1967-73 2 barrel carburetors. 289/302/351W/351C engines. Replaces Ford Part #: C3AZ-9447-B *Excludes 1968 X code 390-2V premium fuel engines.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.

[No Description Provided]

New Old Stock Ford small block Ford distributor shaft to engine block gasket, made of rubber. Fits all 260, 289, 302, 351w, 351c engines. 1959-76. This is a "O" ring rubber washer. Will not fit big block FE, 360, 390, 410, 427, 428 engines. Ford part number B9TF-12143-A.

New Old Stock Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

Made from fuel resistant cork like original.  Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...

Replaces part #C0AF-9276-A. Goes between fuel sending unit and tank.

Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.

Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.

Gasket for mounting the oil filter adapter to any FE or Ford 360, 390, 410, 427, 428CJ engine. Name brand gasket, fits all 1967-70 Mercury Cougar or Ford Mustang with S, X, R, Q, or W code engines.

OEM Cork Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.

Rubber Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.

OEM Style Oil Pan Gasket. Four Piece Gasket.

One piece molded rubber gasket with metal core. Keeps the rails flat and rigid, and prevents damage from over-tightening. Made by Fel-Pro. Oil pan SnapUps are included for easy mounting. This is by far the best oil pan gasket on the market.

New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.

Replaces Ford part #C7AZ-13568

Thermostat Housing Gasket BY FEL-PRO® Replaces Ford Part #: C5AZ-8255-A.

Thermostat Housing Gasket By FEL-PRO® for the Big Block. REplaces Ford Part #: C7ZZ-8255-D.

New water pump plate gasket for the Mercury Cougar or Ford Mustang.

New water pump gasket for FE Ford engines. 1967-70 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. Single gasket, two gaskets needed for installing your water pump. Price is for one gasket only.

New water pump gasket for 1967-69 Mercury Cougar and Ford Mustang with 289/302/351W. Single gasket for sealing water pump to water pump plate only.

Premium quality, exact fit plastic gasket set for both the driver and passenger side door handles. Also fits 66-71 Ford Fairlane and 70-71 Cyclone / Torino as well as several other Mercury, Ford Lincoln models. We are the exclusive retailers in the U.S. for this quality kit.

These 1969-70 Mercury Cougar chrome door handle gaskets are the closest fit to the original Ford gaskets on the market. 4 pieces as shown, enough for both door handles only, round lock gaskets sold separately.Will also work on 70-71 Cyclone and Torino.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1969-73 small block Ford engines with size 351 cubic inches, Windsor engine only. 1969-70 Mercury Cougar and Ford Mustang with 351W engines.Any doubts? 351 windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 289/302 engines. *Note - Excludes 351C or 351 Cleveland engines.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1967-70 big block Ford engines with size 390, 427, or 428 cubic inches, FE engine only. 1967-70 Mercury Cougar, Ford and Ford Mustang.

New timing cover gasket set for 1967-70 Mercury Cougar and most all Fords with 289/302/351W engines. Gasket set includes; timing cover gasket, crankshaft seal, water pump gasket for early or late water pumps, and the oil pan corner gaskets under the timing cover.

New timing cover gasket set for the 1967-70 Mercury Cougar and most Fords with 390-2V, 390-4V, 427-4V, and the 428 Cobra Jets. Gasket set includes; crankshaft seal, timing cover gasket, two water pump gaskets, fuel pump gasket, and oil pan to timing cover gasket.

Cork valve cover gaskets for any big block Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Rubber valve cover gaskets for any FE 390 or 428 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Gasket that creates the seal between the backup light lenses (also known as the reverse light lens) and the chrome housings on the 1969 and 1970 Mercury Cougar. Sold as a pair. Replaces Ford part # C9WY-15510.

Cork gasket for the disc brake splash shield. Fits all 1968-73 Mercury Cougar and Mustang and 1968-71 Ford mid size including Torino, Cyclone, Ranchero, Fairlane.Replaces Ford part number C8OZ-2B160-A.

Seals the lenses to the light body mounted in the front valance. Replaces Ford part # C9WY-13211. Sold as a pair. Also used on 1970 Mach I and 1969 - 1970 Shelby.

Replaces Ford part #C9ZZ-6344228, sold as a pair. This is our economy version.

These are Concours quality with correct bevel and markings.. Sold as a pair.

These reproduction lens gaskets are a perfect fit and are sold as a pair for your Mercury Cougar.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Cork valve cover gaskets for any 289/302/351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

Rubber valve cover gaskets for any 289 302 351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

New set of floor kick panel fresh air vent gaskets / seals for all 1969-1970 Mercury Cougars and Ford Mustangs. Die cut gasket copied from originals that have mounting holes in them. These foam gaskets are 1/4 inch thick. Casting number as seen on seal reads C9ZA-18B290-D. Replaces Ford part # C9ZZ-6501999.

Clean tested and working gauge that will be undamaged by the sun. Our instrumentation technician inspects, cleans, and zero's out the gauge. Check out the video below on our new gauge tester: ...

Gasoline or Fuel gauge assembly for a 1969 Mercury Standard Model. NOS new old stock. 1969 fuel gauges do not have any lettering on the warning lights. 1970 has the white lettering on "ALT" and "PARK" warning lights. Ford part number C9WY-9280-A. Check out the video below on our new gauge tester: ...

Gasoline or Fuel gauge assembly from a 1970 Mercury Standard Model. NOS new old stock. 1969 fuel gauges do not have any lettering on the warning lights. 1970 has the white lettering on "ALT" and "PARK" warning lights. Ford part number C9WY-9280-A. Check out the video below on our new gauge tester: ...

Gasoline or Fuel gauge assembly from a 1969 Mercury Standard Model. Bench tested and working fuel gauge. 1969 fuel gauges do not have any lettering on the warning lights. 1970 has the white lettering on "ALT" and "PARK" warning lights. Check out the video below on our new gauge tester: ...

Used analog style fuel gauge for all 1969-70 Mercury Cougar XR7 and Mercury Cougar Eliminator. Bench tested and working gauge. Ford marking on the gauge C9WF-9306, Ford MPC number C9WY-9280-B.Check out the video below on our new gauge tester: ...