1969 Mercury Cougar

Reproduction dual exhaust tip to hanger clamp for the 1967 - 1970 Mercury Cougar and Ford Mustang.

Used distributor clamp with bolt, for any 260 / 289 / 302 / 351W / 351C / 429CJ built from 1963-1973. May come with either an original used bolt or the new bolt made by AMK Products. Ford part number C3AZ-12270-A.

Includes battery clamp and bolts required to mount battery on tray. Please note that vinyl coating will almost always crack along edges shortly after installation.

Reproduction pair of exhaust pipe clamps for your 67 - 69 Cougar or Mustang.

Reproduction clevis for the tilt/tilt away steering column equipped Mercury Cougar or Ford Mustangs. This unit attaches the pawl cable to the vacuum motor shaft. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This A/C tag clip fastens the aluminum tag to top of the A/C pump.

Used retaining clip for the adjustment bar in the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. Two required per car, used to hold the tilt position adjustment bar in place.  * While not technically correct, this also will work for 1970 - 1974 Cougar/ Mustang tilt columns. SOLD INDIVIDUALLY*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Used clip for the adjustment tension spring for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

New replacement mounting clip as found on select alternator wiring harnesses 1968-70 Mercury Cougar and Ford Mustang and others. Black plastic clip that tapes to the alternator harness and allows harness to be attached to one of the threaded lugs on the reverse of the factory alternator.  Ford part number C6AB-14A163-K.

Used clip found on select alternator wiring harnesses 1968-70 Mercury Cougar and Ford Mustang and others. Black plastic clip that tapes to the alternator harness and allows harness to be attached to one of the threaded lugs on the reverse of the factory alternator.  Ford part number C6AB-14A163-K.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Used dash pad clip for any 1969-70 Mercury Cougar or Ford Mustang. This clip attaches to the steel dash assembly. The lower portion of the padded dashes just above the glove box door and steering column is where they attach. We have seen anywhere from 2-4 or zero of these clips installed on 1969-70 Cougars. According to Bill Q. these clips prevent the sharp dash pad screws from coming into contact with wiring or wiring harnesses. His go-around is to only use blunt screws (without a point) for...

These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Clip or X-washer for attaching the emergency brake lever inside the rear brake drum. Fits 8 and 9 inch rear axles. Literally used on most all Ford products from 1965-73 and likely beyond. Also called a retainer for the parking brake lever pin. The long ears get squeezed with a good set of pliers for attaching. Replaces Ford number 91A-2106. 

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible.

Special clip for attaching the pull cable to the right or left fresh air vent on any 1969-70 Mercury Cougar or Ford Mustang.

Exact copy of the hard to find original. This two piece clip is used to mount gas and/or brake line to floor pans.

Partially dipped clip for attaching the fuel line harness or trunk wiring harness, or fuel line at fuel tank. Found in various places on 1967-70 Mercury Cougar and Ford Mustang.

Reproduction clip for attaching the 1969 front fender extension moulding / trim and the 1970 hood moulding / trim found on the Mercury Cougar. The 1969 application calls for 2 of these clips along with 1 larger clip per side. If you need the larger clip for the 1969 front fender extension moulding / trim, you can get'em right here. The hood lip brightwork for the 1970 requires 4 per side.  *NOTE* The threaded stud on this clip is a little longer than the original ones. This...

Used front fender extension moulding / trim clip for the Mercury Cougar. This is the largest of the three clips required to attach the aluminum 1969 fender moulding / trim to the extension. One is used on each side at the tail (larger part) of the trim piece. This unit is for the purest. If originality is not as important to you, you can get the inexpensive reproduction here.

Used clip for attaching the front fender extension moulding / trim on the Mercury Cougar. The fender extension moulding / trim is sometimes called the eyebrow moulding / trim. This piece of brightwork requires a total of 3 attaching clips, 2 smaller clips and one larger. If you need the larger clip, you can get'em right here! This used original clip is for the purest who values originality. If originality is not an issue, you can get our inexpensive reproduction clip here and save a...

Reproduction large moulding / trim clip for the rear quarter extensions and front fender extensions on the Mercury Cougar. The molding / trim on the 1967-68 rear quarter extension and 1969 front fender extension both require 2 different sizes of clips to properly hold them in place. For the 1967 and 1968 rear quarter extensions, you will need one of these large clips and 1 smaller clip per side. For the 1969 Cougar you will need 1 of these larger clips along with 2 smaller clips per side. This...

Reproduction clip for attaching the hood lip moulding / trim on the Mercury Cougar and six are required. We do offer good used originals here for the purest, but these will work great at half the cost.

Used hood lip moulding / trim clip for the Mercury Cougar. This unique little clip is found only on the 1969 hood lip moulding and six are required to mount your aluminum hood trim. Be forewarned, there will be varying degrees of surface rust found on these used clips and will rarely look mint. These units are high dollar and are for the purest whee originality is of the utmost importance. If originality is not an issue, you can get our inexpensive reproduction clip right here and save a...

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

Used clip for the stainless steel rear deck / trunk lid moulding / trim for the Mercury Cougar. This clip will also work on the 1967-68 aluminum rear deck / trunk lid moulding / trim. Seven of these units are required per moulding / trim and the acorn nut will have some rust on it. If originality is not a issue, you can get our reproduction clip here and save a little of that hard earned income. For more insight on this tricky trunk trim, check out our video below: ...

Correct plastic rocker moulding clips with Ford engineering # C9WB-6510182-A, Ford part #C9WY-6510182-A. There are five of these on each side for a total of ten per car. These same clips can be found on 1977-1979 Mercury Cougars and Thunderbirds. Most likely they were used on other FoMoCo products. If you know of other applications where these clips can be found let us know so we can post the information to help others in their search. Sold Individually.

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Inside diamenter = 1"

Used plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Known to have been used on 1969-1970 air conditioning boxes to hold a vacuum hose to the actuator.  They can be screwed or bolted to the plenum.   Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used wire loom plastic clip for the Mercury Cougar or Ford Mustang

These clips are found on the power window swtiches of the 69 - 70 Cougar. Each power window switch has one of these clips and one of the J hook clips.6 small clips required per master switch panel, one for each window switch and two per lock out switch.