1969 Mercury Cougar

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and their 30 watt little brother are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Features Kenwood 60 watt peak power speakers, nice upgrade over the low wattage originals. Sold as a pair.   These pictures show what every 69-70 door panel looks like on the backside.  They are all perforated from from the...

D0ZB-13A769-B Left side door wiring harness with decor interior as found on 69 - 70 Standard Cougar (non-XR7's) with door courtesy lights. Also used on 1970 Ford Mustang with decor interiors which include Grande and Mach 1. Wiring harness for courtesy door lights only. Master part number D0ZZ-13A769-B. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage. *Note* Does not include door ajar or factory stereo wiring plugs. ...

C9WY-13A769-A-AGRADE Right side door wiring harness that includes door ajar and courtesy lights. Found on 1969 XR7's and 1969 Standard Cougar with Safety Convenience Package. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway.

C9WY-13A769-A Right side door wiring harness that includes door ajar and courtesy lights. Found on 1969 XR7's and 1969 Standard Cougar with Safety Convenience Package. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

This restored passenger side (right hand) drip rail moulding / trim has had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as one side only, or as a pair. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used drip rail mouldings / trim. The vinyl top...

These restored driver side (left hand) and passenger side (right hand) drip rail mouldings / trim have had all minor dings and scratches removed and then polished to a mirror like finish. These mouldings have been restored far beyond the quality that your car came with from the factory. These are sold outright, as a pair, or one side only. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used drip rail...

1967 - 1969 390-4V engines with 3 or 4 speed manual transmissions. 1969 - 1970 Boss 302 Eliminator 4 speeds. 1970 M-code with 3 or 4 speed manual transmissions. Shaft diameter 3 inches, length 53-1/32" measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

1968 - 1970 428CJ Drive shaft - Used All 428CJ's with 4 speed manual transmissions. Shaft diameter 3 inches, length 53 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.Ford part # C8WY-4602-A.

428CJ engines with C6 automatic transmissions. Shaft diameter 3-1/2 inches. Length 49-41/64 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

This kit was sold by Ford Service Departments back in the day for those who were tired of their manual drum brakes. This kit includes all you will need to convert your six cylinder Mustang or V8 Cougar / Mustang from manual to power drum brakes. Technically it is correct only for a 1968 but will work on any year 67-70. The conversion carries a Ford part number of C8ZZ-2A091-A. Ford was generous and gave you both a manual transmission and a automatic transmission brake pedal in the kit. When...

C9ZA-18C366-A lower heater duct to floor outlet for Cougars or Mustangs without air conditioning. Used grade "B" part that will have more than one minor defect. It will have a small crack and possibly a broken or missing tab. Almost half the price of the grade "A" piece and works awesome if you don't have one at all. Want to have directed heating, we've got you covered.

Flow thru ventilation, power vent, power ventilation system, comfort stream ventilation, are some of the various names for this rare option found on 1969 Mercury Cougar, Ford Mustang and Shelby Mustang. Back in 1969 it was a $40.02 option. It allowed fresh air to be blown through a center vent. Often confusing, because it looks like half of an air conditioning system.Ford casting number C9ZA-18C299-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to...

Fuel pump drive eccentric for most big block Ford engines 1963-70. Including 352, 360, 390, 410, 427, and 428. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 3-3/8 inches in diameter. Ford part number C3AZ-6287-A.

Correct cast aluminum elbow fitting for the rear of the C8AZ-9A486-C smog pump. This elbow will have two single mounting holes. The service replacement elbow (Ford part number D4TZ-9C475-A) has two sets of double mounting holes. Correct Ford part number C8AZ-9C475-A.

Reproduction chrome heater hose elbow is for 351, 390, and 428CJ engines. Replaces Ford Part # D0AZ-18599-C Barbed End: 5/8" hose barbThreads: 1/2" NPT (Tapered Threads) For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Elbow with water restrictor.

Concourse correct 90 degree heater hose elbow that attaches to the intake manifold and provides proper clearance for the emissions canister and air cleaner housing. Correct for all Boss 302 and 428CJ engines 1969-70.Ford number C9ZZ-18599-A.

NOS never installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender. Sold individually Replaces Ford Part #: C8OZ-16228-D.

NOS never installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender. Sold individually Replaces Ford Part #: C8OZ-16228-D.

Nice reproduction of the factory installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender.Sold individuallyReplaces Ford Part #: C8OZ-16228-D.

These were obtained from the original manufacturer and have never been mounted. Very rare find!

Rare find in NOS form! 1969 standard model Cougar, passenger side dash plate. Replaces Ford part number C9WB-6504460-A.

Due to the fact these were glued on, they are often missing. Separate "XR" and "7", Grade B used, good for a daily driver. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line workers did not even attempt to get them very well centered. Both emblems were placed on the RH side of the deck lid...

Original part in Ford box, part number C9WB-16098-A, casting number as seen on back is C9WB-16098-B

NOS front fender extension "Cougar" script. Ford Engineering number as found on the backside:  Ford number C9WB-16098-B. 

NOS front fender extension "Cougar" script. Ford Engineering number as found on the backside: Ford number D0WB-16098-A . 

This version of the emblem was actually used on early 70's full-size Mercurys, and is almost identical to the 1969-70 version used on Cougars. In order to use it on a Cougar fuel door, the studs on the back will need to be trimmed down The only visible difference is the thinner / more numerous ridge lines in the red crest area than on the Cougar version. Casting number on this substitute emblem is D1GB-16607-AA.The original emblems were never sold as a stand alone part from Ford but rather an...

These fuel door Mercury crest emblems are a close to original reproduction. They are an economical alternative to brighten up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. To remove your emblem we suggest grinding down the studs on the backside. To install the reproduction emblem you will need the 26120 trim clip.

These fuel door Mercury crest emblems have been lovingly restored by a long time Cougar enthusiast. They have been carefully repainted the correct colors and will really liven up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. The engineering number on the back is C9WB-65405A92. To remove your emblem we suggest grinding down the studs on the backside. To install the restored emblem you will have to use epoxy glue. Keep in mind you...

Very difficult to find, delicate aluminum quarter panel emblem in the original Ford box. Ford part number is C9WB-6525622-A, casting number on back reads C9WB-65291B62-AYou can reference the above pictures for correct dimensions, as taken from one of our cars using an original script emblem. Measurements are from the rear and lower body lines.

Good used center with no crack, missing paint or broken mounting tabs. This was used on all 1969 Cougars with a three spoke wheel except the XR7.

This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. We rarely have an emblem this nice in stock for more than a few weeks of any one year as the tail was prone to breaking off as well as the "cats" other limbs. We do not list these hard to find parts here to...

This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. The tail will always be broken and probably at least one leg is missing on this grade B part. While not an exact fit our 3 spoke wheel emblem cat will fit on this black background.

COMING SOON Beautiful reproduction C pillar emblem for the 69 - 70 Cougar XR7. This part is also known as the shield or outside roof side ornament. The attention to detail on this exact copy is really impressive. Kudos to Daniel Carpenter Mustang for providing yet another outstanding part. Sold individually, 2 required per car. No core required. Replaces Ford part number: C9WB-65517A56-A Black plastic backer engineering number reads C9WB-65517C00-A Engineering number on back side of chrome...

These two emblems were sold separate when ordered as a service replacement part. We sell them as a pair. Located on the passenger side of the trunk, these are a peel and stick with no mounting studs. Ford part # C9WY-6542532-A & C9WY-6542532-BWe often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the...

Used emergency / parking brake assembly for the Mercury Cougar or Ford Mustang and is as removed from a West Coast Cougar organ donor. 1969 had a weak design and the release levers were prone to bend and break off. 1969 used a T shaped chrome release handle and 1970 used a black plastic T shaped release knob, which generally aren't interchangeble. Seldom in stock, please check out the reproduction version.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 351W engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C9OE-6015 casting. Dated 9J23, September 23, 1969. Picture may show item with damaged oil pan and crank shaft and pistons. When we have them in stock we will post the casting date or dates. Heavy, will require...

Chassis black aerosal paint for all 1967-73 Mercury Cougar and Ford Mustang engine compartments. High temperature (advertised up to 350°). Manufacturer boasts resistant to cracking and flaking, chemical resistant to gasoline and brake fluid (but don't let brake fluid accumulate). *NOTE* Chemicals can only ship UPS ground only. Please, no foreign orders or USPS shipping allowed.Check out our video below on chassis upgrades: ...

Assembly line used engine lift hook. Passenger side 1969-70 with 428 Cobra Jet engines, including 428SCJ. Triangle shaped, with one single hole for the hook. Not stamped with number. Fits all 1968-70 Ford cars with either R code or Q code 428 engines. Cougar, Mustang, Cyclone, Torino, Talledega, Cobra, Fairlane, Montego, Ranchero etc. Attaches to the passenger side exhaust manifold. There is also a driver side engine lift hook, see related items. 

C7OE-9431-A Factory original cast iron exhaust manifold for driver side. 1967, 1968, and 1969 390/427 left side manifold remained unchanged for all three years. Includes 1968 X code 390-2V Premium fuel cars. Click on images to enlarge. ...

Factory cast iron exhaust manifold set, both a correct right C6OE-9428-A and left C7OE-9431-A side matching exhaust manifolds. With 1969 dates. *TRIVIA* 1969 390 S code Cougars were not technically the 390GT variety. An Autolite 4300 carburetor and a non-GT intake manifold changed the designation to 390IP for "Improved Performance."

C8OE-9431-B 428 Cobra Jet factory original cast iron exhaust manifold for driver side. For all 1969-1970 428CJ Cougars after 9/2/1968 build date.

C9ZE-9431-A Factory original cast iron exhaust manifold for driver side. Correct for all Boss 302 Eliminators 1969 and 1970.

C9ZE-9428-A Factory original cast iron exhaust manifold for passenger side. Correct for all Boss 302 Eliminators 1969 and 1970. Nice piece from a CA car, no damage or pitting.

351 Windsor factory cast iron exhaust manifold set, both a correct right C9OE-9430-B and left C9OE-9431-B side matching exhaust manifolds. Same manifolds used on all 351 Windsor engines in 1969 and 1970.  No extra charge to look for a date coded pair but no promise we can hit it spot on either.  

428 Cobra Jet factory cast iron exhaust manifold set, both a correct right C8OE-9430-D and left C8OE-9431-B side matching exhaust manifolds.

Factory cast iron exhaust manifold set, both a correct right C9ZE-9428-A and left C9ZE-9431-A side matching exhaust manifolds. 1969 and 1970 Boss2 Eliminators

For factory installed A/C on Mercury Cougars and Ford Mustangs. This unit functions great, but when compared to the NOS unit, you will see that it is cosmetically a little bit different. This uses the "O" ring style seals which are not included.Will work with both R12 and R134 systems.