1969 Mercury Cougar

Replaces Ford Part #: C8WB-17093-D.

Correct for the 1969 Eliminator SS wheel. Replaces Ford Part #: C9WB-17093-B

This decal goes on the tire jack itself.

Used jumper wire with correct ends for doubling back on the tachometer leads from the under dash harness. Works for all generations 1967-68, 1969-70, and 1971-73 Ford anything and Mercury, and Mercury Cougar with factory tachometers. If your tachometer goes bad, you will not start or keep your engine running. Good for bypassing tachometers for testing and getting home. Keep in your glove compartment or tool box.

Brake switch jumper wire, 4 inch long extension. Bridges the under dash wiring harness and the brake light switch. Not used on many cars, we suspect that it was used on the assembly line when the brake switch plug didn't reach the brake switch. Adding one of these jumpers, saved time from re-routing the under dash wiring harness. This jumper can also be used to repair bad stop light connectors on 1967-70 Cougars and Mustangs (and other Fords) by cutting off the male end and splicing it...

Brake switch jumper wire, 4 inch long extension. Bridges the under dash wiring harness and the brake light switch. Not used on many cars, we suspect that it was used on the assembly line when the brake switch plug didn't reach the brake switch. Adding one of these jumpers, saved time from re-routing the under dash wiring harness. Ford master part numbers: C5AZ-14489-C, C8ZA-13K408-A and C8ZZ-13K408-A

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford #: C7AZ-6222053-A.

Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford Part #: C7AZ-6243562-A.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the ignition / door key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

This listing is for a Walking Cat keychain multi tool. We haven't been able to find much information on this, but it's definitely a cool item to add to your collection. Features a chrome plated swing out tool with a few flathead tips and nub-style phillips tips. 

Kickdown return spring for 1967-68 Mercury Cougar with C4 transmissions, and 1967-69 Mercury Cougar with C6 transmissions. Same for 1965-69 Ford Mustang with C4 and 1967-69 with C6. Actual Ford part number is C5ZZ-7B146-A.

According to the Master Parts Catalog, this rod was used on all 1969 Cougars equipped with a C6 transmission which includes the 390IP / 428CJ / 428SCJ. Our research and in hand examples off original Cougars would differ. Because of the different intake manifold used on the 390, Autolite carburetor vs. Holley and different exhaust manifolds we have found that the 1969 390 IP / C6 is distinctly different than the 428CJ and stands on its own by not interchanging with any other Ford product. ...

Exact reproduction made by Daniel Carpenter. Injection molded black plastic. Very nice. Much thicker and more durable than other reproductions. Sold as a pair. Replaces Ford Part # : C9ZZ-6502344/5

Used knob for wiper control switch on dash panel. Constructed of metal with chrome, may show some wear on the black painted section and flaws in the plating.Ford part number C9ZZ-17513-C.

Chrome and black knob just like the original.NOTE: This knob is correct for 1969. It will fit on a 1970, however the orientation of the pointer will be off. You can find a good used 70 knob here. Replaces Ford Part # : C9ZZ-17513

Nice clean set of four used radio knobs for your 69-70 Mustang or Cougar. No peeling or cracks. The inset picture shows the used next to the new from the backside. The reproductions are shown on the right. Whereas the repros are nice, the originals are still superior. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. White plastic reproduction spacers available here. The white...

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.

Used lower knuckle for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This unit will not interchange with the 1967 tilt / tilt away. This is because the center hole on the 1967 unit is round where this 1968-69 version is elongated. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of...

Used upper knuckle assembly for the tilt / tilt away column for the Mercury Cougar or Ford Mustang equipped with a tilt / tilt away steering column. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* We'll give you UP TO $100 cash back for your old knuckle assembly. The amount you will get back will depend upon how many usable parts that can be salvaged from your old unit. *NOTE* For tilt column service, you can contact Tony...

Good used "L" bracket for the tilt cable adjustment on the 1968 and 1969 Cougar or Mustang.

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-ACheck out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

During installation, check for proper alignment with trunk latch. Trunk latch and striker should engage smoothly, both items are adjustable. We only save the rust free latches with no wear or rust, the rest are tossed. Fits 1969-70 Mercury Cougar and 1968-69 mid sized Ford Torino, Fairlane, etc. 1968-69 Mercury Cyclone, Montego, etc. Ford part number C5AZ-6243252-B.

Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650509-K. Casted Pot Metal with Engineering # C4ZB-7650535-C

Used driver side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired.  Ford part number C4ZB-7650535-C.

Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650508-KCast Pot Metal with Engineering # C4ZB-7650534-C

Used passenger side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired. Ford part number C4ZB-7650534-C.

Stamped steel A/C lateral support brace for all Mercury Cougars and Ford Mustangs with the 351-2V or 351-4V Windsor engines. Ford part # C9OZ-2888-B. *NOTE* - Excludes all 351 Cleveland engines and 1970-71 351 Windsor engines.

Used steel lateral support brace for Cougars and Mustangs with the 390-2V, 390-4V, or 428CJ FE engines. Identical to the 1970 FE lateral bracket except 1970 versions have square nuts on the reverse.Ford part # C8AZ-2888-A

Used steel lateral support brace for Cougars and Mustangs with 428CJ FE engines. Identical to the 1968-69 FE lateral bracket except 1970 versions have square nuts on reverse. Also the same bracket for Ford passenger car 390 up until 1971.Ford part # D0AZ-2888-B

Used driver side leaf spring, front mounting bracket. 1967 Mercury Cougar. 1968-73 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used driver side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used passenger side leaf spring, front mounting bracket. 1967 Mercury Cougar. 1968-73 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used passenger side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...