1969 Mercury Cougar

Used map light assembly for the Mercury Cougar standard or Eliminator. This unit has the switch installed on the housing and mounts under the dash pad on the passenger side (right hand). Assembly comes with housing, lens and wiring harness. After January 1970, Mercury changed the housing to plastic. We occasionally have those versions, please ask. This unit measures about 6-1/8" long, 1-11/16" wide and about 1-5/16" deep. *NOTE* Because this unit has the switch mounted in the housing, it...

Reproduction map light assembly for the Mercury Cougar XR7. It mounts under the dash pad on the passenger side (right hand) and comes with the housing, lens and wiring harness. Hardware included. *NOTE* This unit is not the same as the one that is used on the Eliminator or standard Cougar. The standard / Eliminator unit has the switch in the housing.

Used map light assembly for the Mercury Cougar XR7. This unit mounts under the dash pad on the passenger side (right hand) and comes with the housing, lens and wiring harness. After January 1970, Mercury changed the housing to plastic. We occasionally have those versions, please call for availability. This unit measures about 6-1/8" long, 1-11/16" wide and about 1-5/16" deep. *NOTE* This unit is not the same as the one that is used on the Eliminator or standard Cougar. The standard /...

Used white plastic instrument cluster mask for any 1969 Mercury Cougar, standard or XR7. This is the part that the clear lenses attach to. Ford casting number C9WF-10894, Ford part number C9WY-10890-.

Mask, or shroud, that holds the clear lens for either the tachometer on an XR7, or clock or clock blank on any 1969-70 Mercury Cougar. This also fills the gap between the white plastic gauge mask and the tach or clock.  Ford casting number C9WF-10894.

New master cylinder for the Mercury Cougar or Ford Mustang equipped 4 wheel power disc brakes. This unit can be used with the Bendix and Midland boosters. Bore size: 1" WARNINGS: Do not attempt to use a 1970 booster on a 1967-69 Cougar as failure will occur within minutes! Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty. ...

New reproduction power disc brake master cylinder for the Mercury Cougar or Ford Mustang equipped with factory power disc brakes in front and drums in the back.  This unit has a 1" bore and includes a new cap and diaphragm as shown.  Unlike many others you will find, this unit does not need brass line adapters to fit your factory lines, they are correctly sized, will not interfere with your shock tower and ready to bolt on.   Has proper threaded line size for OEM or...

New premium reproduction tear drop power disc brake master cylinder for the Mercury Cougar or Ford Mustang equipped with factory power disc brakes in front and drums in back. Has proper threaded line size for OEM or replacement brake lines, 3/8-24 and 1/2-20. The main difference between this unit and our economy version is cosmetics, as this premium unit comes with the correct "tear drop" casting; other difference to consider are this unit has a 1" bore, instead of 1 1/8"...

Reproduction master cylinder for the Mercury Cougar and Ford Mustang equipped with power drum brakes. These are brand new units, not rebuilt, and are made from high quality American made parts. WARNINGS: Do not attempt to use a 1970 booster on a 1967-69 Cougar as failure will occur within minutes! Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty. ...

Complete engine mounting hardware kit for the 1969 351W engine. See below for a list of included hardware. Click on images to enlarge.

Complete engine mounting hardware kit for the 1969 351W with A/C. See below for a list of included hardware. Click on images to enlarge.

Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...

AMK engine fastener kit for 1968-69 Mercury Cougar and Ford Mustangall with S code 390-4V or 390GT engines. This kit claims to have 138 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water neck, water pump,*Note -...

AMK engine fastener kit for 1969 Mercury Cougar and Ford Mustang / Fairlane all with R code 428 Cobra Jet engines. This kit claims to have 157 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water neck, water...

Complete engine mounting hardware kit for the 1969 Boss 302. See list below for included hardware. Click on images to enlarge.

The car pictured is a 67, but the copyright says "1969 Fred Bonner Corporation" and the header says Mercury Cougar introduced 1968.Measures 5"x7"

NOS 1969 Mercury Competition Team pamphlet. These packets were handed out to Mercury team dragsters in order to log their run times. Once you logged enough class wins, the concept was to mail the pamphlet to the Mercury Competition Team Headquarters and claim your Mercury Competition Team Driver's Award Certificate. Originally these booklets included stickers and decals, but those seem to be missing from this particular booklet. Also included is an order form from that year to...

Reproduction intake manifold spacer for the Mercury Cougar or Ford Mustang equipped with the 390 or 428 engine. Sold individually, # VI.

This 12" x 18" parking sign is the perfect way for your Cougar to mark its territory. Bold red lettering announces that lesser cars are not welcome. Durable .040 gauge aluminum with two pre-drilled holes for easy hanging. Makes a great gift!Our review: Print quality isn't as crisp as actual road signs if you look real close, but it looks good from a couple feet away. Seems durable enough for outdoor use. We're testing them in the parking lot outside our shop for UV resistance, stand by for an...

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. Fits 1969-70 Mercury Cougar and Ford Mustang.

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. Fits 1969-70 Mercury Cougar and Ford Mustang.

This little switch is mounted on the back side of your interior temperature control panel on most 1969-72 Ford products. It energizes the A/C pump when you move the the knob to the "A/C" position. Correct dimensions and easy to install. Starting sometime in 1972, this switch was incorporated with the vacuum selector manifold. This is part of the switch assembly C9ZZ-19B888-A.

This little switch is mounted on the back side of your interior temperature control panel on most 1969-72 Ford products. It energizes the A/C pump when you move the the knob to the "A/C" position. 15 AMP micro switch. Starting sometime in 1972, this switch was incorporated with the vacuum selector manifold. This is part of the switch assembly C9ZZ-19B888-A.Tested and guaranteed to work, originally produced by Cherry Electrical Corp.

Special cast-metal bracket glues to windshield. Fits the original and most reproduction mirror ball arms. This version is shiny chrome instead of satin silver like the originals. The screws are also incorrect. Otherwise nice quality.

Tired of your mirror falling out of adjustment? This installs easily and is correct in all details. Unlike the two piece unit we offer this one has the correct satin finish and correct screws. Replaces Ford Part #: C2SZ-17690-F. Reference from mercurycougar.net: Best guys to always talk to about Cougars..will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when you're talking 'cause you're important to them. Greatest thing for...

Restored original XR7 sport mirror base for the 1969 Mercury Cougar.  Ford part number C9WB-17743-C

Original, used hard plastic 1969-70 driver side mirror pad / gasket. Fits 69-70 driver side Sport mirrors, and 69-70 driver side Chrome mirrors on the Mercury Cougar. Will not work on the passenger side. Notice this is not a flat pad but has an angle built into it. MUCH better fit than the mushy flat rubber repro. Ford part # C9WY-17724-A, Ford engineering # imprinted on gasket C9WB-17C701-A Do you have riv-nut questions? Here are riv-nut answers! ...

Driver side (left hand) mirror pad / gasket made of very soft rubber. Fits 69-70 driver side Sport Mirrors, and 69-70 driver side chrome mirrors on the Mercury Cougar. Will not work on the passenger side. While this is "better than nothing" it will never fit or look correct. We highly recommend purchasing our good used hard plastic mirror pad that is especially contoured to fit the door on the driver side. Replaces Ford Part # C9WY-17724. Do you have riv-nut questions? Here are riv-nut...

Authentic looking hard reproduction plastic Sport Mirror pad gasket. Correct for driver side Cougar Sport Mirrors 1971-73 and passenger side Torino / Cougar Sport Mirrors 1970-73. This is the best fitting gasket we've found so far. You may have to punch out the hole for the remote mirror cable. Replaces Ford #: C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video Check out this video ...

Designed as a direct-fit OE-style replacement, this modulator valve will fit directly into the factory location of your current Cougar or Mustang valve. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs.

Designed as a direct-fit OE-style replacement, this modulator valve will fit directly into the factory location of your current Cougar or Mustang valve. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs.

Transmission Vacuum line OE for the C6 transmission with 90 deg. bend at trans.

Stainless Steel Transmission Modulator Line for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang with the C6 transmission.

OE Steel Transmission Modulator Vacuum Line for the 1969 Mercury Cougar or Ford Mustang with a 351 Windsor and an FMX transmission.

Stainless Steel Transmission Modulator Vacuum Line for the 1969 Mercury Cougar or Ford Mustang with a 351 Windsor and an FMX transmission.

Curved Monte Carlo Bar in a black finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford Part # C9ZZ-16A052-BRB. ...

Curved Monte Carlo Bar in a chrome finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford part # C9ZZ-16A052-BRC. ...

Straight Monte Carlo Bar in a chrome finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end of your coddled cream puff cruiser or hardcore corner carver, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford part # C9ZZ-16A052-ARC. ...

Reproduction power window motor for the driver side (left hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear pancake style motor, you can find that here.*NOTE* This is the only version of the power window motor that is available at the moment....

Used power window motor for the Driver side (left hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear pancake style motor, you can find that here. ...

Reproduction power window motor for the passenger side (right hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear pancake style motor, you can find that here. *NOTE*  This is the only version of the power window motor that is available at...

Used power window motor for the passenger side (right hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear quarter window pancake style motor, you can find that here. ...

Nice reproduction of an obsolete motor mount. Left is the same as right, sold individually. This isolator is used with the 390, 427, 428 and 429 Cobra Jet engines.  Sold individually. Replaces Ford Part #: D1ZZ-6038.

Reproduction interior windshield / A pillar post mouldings / trim that features a vinyl overlay and 2 inch gauge pods on the driver side (left hand) so you can add any gauges of your choice to your Mercury Cougar or Ford Mustang. These units are sold in pairs.

Interior windshield / A pillar post mouldings / trim for 69 - 70 Cougars and Mustangs that feature two 2" gauge pods on the driver side. Sold as a pair.  These are not the best fit but will work, notice it requires exterior screws to mount them. No returns.

Restored lower left rear window moulding / trim for the Mercury Cougar.

Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503137-A. *NOTE* If you have questions about your cores, checkout our video below. ...

Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Restored passenger side (right hand) vertical windhield moulding / trim for the Mercury Cougar. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. When you purchase one of our stainless trim parts you are paying for the removal of dings and scrapes as well as the polishing of the part.  Ford part # C9ZZ-7603144-B....