1969 Mercury Cougar

Nuts and bolts, associated with the installation of our used 1968-69 strut rods. 1 large and medium nut for the front, and two bolts and nuts to attach to the lower control arm.

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

Reproduction 8-32 x 1/2" stud used to attach the convertible boot mouldings on any 69-73 Cougar or 65-73 Mustang. A number of these studs were installed on the mouldings, going through the body of the car and attached underneath the sheet metal using the boot nuts.

These studs attached the taillight housing to the tail panel of a 1969-70 Cougar. 6 used per taillight, 12 required per car. Sold individually.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Stud for attaching exhaust manifold heat shield on 1969 Mercury Cougar or Ford Mustang with 351W. Sold individually. Replaces Ford Part # 382592-S

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 

Stud for attaching exhaust manifold heat shield on passenger side. Sold individually Phosphate & Oil (gray-black) Replaces Ford Part # 382338-S

This kit mounts the spoiler pedestals to the trunk lid. Studs measure 2-3/4" long, correct for the Concours correct stands.Some economy or generic kits come with 1-1/2" studs

Reproduction studs and nuts for the taillight to body on the 1969 - 1970 Mercury Cougar 

This wheel was optional on any 1969-70 Cougar except the 1969 Eliminator which came standard with the 12 hole painted rally wheel. In 1970 the Eliminator used this SS wheel but it was optional, not standard equipment.  These are exact reproductions in every way except they are welded, not riveted to the center section.NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do...

Reproduction chrome center cap with blue background and chrome Mercury man logo for the Mercury Cougar. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the...

Reproduction chrome center cap with red background and chrome Mercury man logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from...

Chrome center cap with Blue background and chrome walking cat logo for the Mercury Cougar. Better than original! New from Scott Drake. These quality center caps feature our high quality chrome bezels. Check out the details in our "Cougar" lens. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing,...

Reproduction chrome center cap with red background and chrome walking cat logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good...

Excellent quality reproduction sun visor assemblies and corner trim for the convertible 1969 - 1970 Mercury Cougar or Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. Sold as a pair, the original passenger side part has a C9ZB-7604122-C casting number on the back side and the driver side reads C9ZB-7604123-C. These will also interchange with versions ending in A B or D. Later versions will show one less screw tab. Replaces Ford part # C9ZZ-7604144 /...

Grade B used convertible sun visor bracket assembly for the driver side of any 1969-70 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results.  These will almost always, show some wear in the pocket, where the hook attaches.Ford casting number C9ZB-7604123.

Grade B used convertible sun visor bracket assembly for the passenger side of any 1969-70 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results.  These will almost always, show some wear in the pocket, where the hook attaches.Ford casting number C9ZB-7604122.

Used single hole front mount center visor bracket for the 1969 / 1970 Mercury Cougar and Ford Mustang hard tops.  The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your desired color in the 'comments' section of your order. Ford part # C9AZ-6204132, casting # C9AB-6204132-B.

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Reproduction single hole front mount center visor bracket for the 1969 and 1970 Mercury Cougar or Ford Mustang. This is a decent reproduction, but not quite as nice as the originals. Reproductions only come in 'paint to suit' black but we have most original colors in used. Replaces Ford Part #: C9AZ-6204132.

For the purists out there we have a very limited amount of used visors that have no impressions, seam separation and minimal rust on the clips if any. Convertible and Coupe are the same.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually

Reproduction sun visors that are fully padded and covered with the correct textured vinyl to match the seats. These units are sold as a pair.

This decal was sometimes placed on the dash face pad near the middle or right side, and sometimes on the sun visor.

Used Driver Side Grade B Center Grille Support for the 1969 Mercury Cougar

Used Passenger Side Grade A Center Grille Support for the 1969 Mercury Cougar

This grade "B" support will be rust free but will need minor straightening on the lower mounting tab. Once worked on the damage should not be noticeable. Customer feedback; Hey Don, I've been ordering parts for my '67 over the last few months from your company. I just want to let you know I would recommend your company to anyone. You have been extremely helpful in every aspect. I think your site is great and easy to use. I especially liked how you call me with questions and answers...

Used  Grade A driver side support / grille center for the 1969 Mercury Cougar

Support brace between the cowl top and the brake pedal support bracket. Fits 1969-70 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Ford part number C9ZB-6501554.

Support brace between the cowl and the top of the brake pedal support bracket. Fits 1969 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Overall width is right at 5 inches on the 1969, smaller than the 1970 version. Ford part number C9ZB-65015A18-A.

C9ZZ-6501508-B This is the correct hanger for a 1969 Mercury Cougar or Ford Mustang with power disc brakes. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number C9ZZ-6501508-B for power disc brakes. *Note - Power brake and manual brake supports are different. Power brake...

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and in unused condition. Ford part # C9ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to...

Reproduction brake pedal hanger also known as the brake pedal support for Mercury Cougar and Ford Mustang.

Used upper support bracket for the hood latch on any 1969 Mercury Cougar. Ford part number C9WY-16707-A.

Used upper support bracket for the hood latch on any 1970 Mercury Cougar. This 1970 part will work on a 1969. The only difference is the top corner is clipped at an angle on the 1970.Ford part number D0WY-16707-A.

Fills the hole in the core support where the A/C lines pass through to the condenser. Replaces part # C9ZZ-19819.

Pair of reproduction cowl vent panel support pads.

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

This is the spring that holds the rear license plate or fuel door in the upright position. Fits 1969-70 Cougar.Ford Part #: C9WY-13455-A

Good aluminum piece that has no corrosion, no dings and all six mounting studs will be firmly in place. This same bezel was used on all Standard, XR7 or Eliminator Cougars for 1969 and 1970. Obviously the clock hole was not utilized on the Standard Cougar.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.  

C9ZZ-5482-D Factory used sway bar for any 1969 Cougar with optional Competition Handling Package. Factory identified with a single 'Green' paint stripe. *Excludes 428CJ and Boss 302 cars, those cars were factory built with a 15/16 inch sway bar. This factory used front sway bar, does not include any mounting brackets or end link kits.

C9ZZ-5482-A 1969 Standard used factory front sway bar. 3/4 inch in diameter. This factory used front sway bar, does not include any mounting brackets or end link kits.