Bumpers & Trim

Set of 8 fine threaded Phillips screw assemblies. This the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the...

This fine threaded Phillips screw assembly is the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The two new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the comparison...

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

Set of 8 1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples. Also sold individually.

1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples.Also sold in a set of 8. ...

Spring that holds the headlight trim ring on each headlamp to the grille. 4 springs per car, sold individually.Ford number C6AZ-13031-C.

Captured washer, or spinning washer nut for attaching the headlamp motors or vacuum actuators on the 1969-70 Mercury Cougar. All models, Standard Hard Top, XR7, and Eliminator. Two needed per car, sold individually.

Grille corner backing plate from a 1969 Mercury Cougar. This will be a driver side with the deep square groove on the side. There are two styles of 1969 grilles, we think that the early version did not have the extra gusseting for strength. We offer these for when they come up missing. These must be removed prior to restoration. We use a small die grinder or Dremel tool to grind the peened rivets on the grille housing. It is important to know which version of grille that you have, these do not...

Grille corner backing plate from a 1969 Mercury Cougar. This will be a driver side with the shallow groove on the side. There are two styles of 1969 grilles, we think that the early version did not have the extra gusseting for strength. We offer these for when they come up missing. These must be removed prior to restoration. We use a small die grinder or Dremel tool to grind the peened rivets on the grille housing. It is important to know which version of grille that you have, these do not...

Grille corner backing plate from a 1969 Mercury Cougar. This will be a passenger side with the deep square groove on the side. There are two styles of 1969 grilles, we think that the early version did not have the extra gusseting for strength. We offer these for when they come up missing. These must be removed prior to restoration. We use a small die grinder or Dremel tool to grind the peened rivets on the grille housing. It is important to know which version of grille that you have, these do...

Grille corner backing plate from a 1969 Mercury Cougar. This will be a passenger side with the shallow groove on the side. There are two styles of 1969 grilles, we think that the early version did not have the extra gusseting for strength. We offer these for when they come up missing. These must be removed prior to restoration. We use a small die grinder or Dremel tool to grind the peened rivets on the grille housing. It is important to know which version of grille that you have, these do not...

We are excited to bring these new reproduction chrome backup light bezels for the 1969 and 1970 Mercury Cougar to the market. The sockets, pigtails and lenses are not included so you will need to gently remove your originals and install them in these bezels. You can find the lenses here.

We are excited to bring these new reproduction assemblies for the backup lights for the 1969 and 1970 Mercury Cougar to the market. Includes a pair of bezels with lenses and gaskets. The sockets and pigtails are not included so you will need to gently remove your originals and install them in these bezels.NOTE: We've been informed that the reproduction lenses will need a bit of filing and sanding to properly fit into these reproduction bezels.

Good used driver side (left hand) driver grade quality bezel with minimal, light pitting, ready to install and use as-is. If you are planning on sending in cores to be restored this is the level you would want to start with. The pitting found on this grade "B" bezel will be light and almost entirely restricted to the top surface which means it will only be seen when the trunk lid is opened. Ford part # C9WB-13504 for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem?...

This is a poor condition bezel with pitting on all surfaces. It is a better than nothing type of part. We do not accept returns on grade C parts.Ford part # C9WB-13449 for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source...

NOS driver side (left hand) taillight bezel for the Mercury Cougar.Ford part # C9WY-13489. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send...

Grade "A" passenger side (left hand) bezel with no pitting, ready to install and use as-is. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Check out this video ...

This is a poor condition bezel with pitting on all surfaces. It is a better than nothing type of part. We do not accept returns on grade C parts.Ford part # C9WB-13449 for the passenger side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great...

Beautifully reproduced set of chrome driver and passenger side taillight bezels for the 1969 Mercury Cougar. Replaces Ford part # C9WB-13504 for the driver side. Replaces Ford part # C9WB-13449 for the passenger side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

Bolt for installing the front bumpers on any 1969-70 Mercury Cougar or Ford Mustang. Threads into the front frame rails. 4 needed per car. Sold individually#56362-S

Fits all models.

Reproduction Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang.If you're working on both sides of your grille, you will need two kits, one kit will do one half of the grille.

Reproduction Headlamp Housing Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang

Powder Coated. Replaces Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

Used to mount the vacuum storage tank inside the driver fender, two required per car, sold individually. Exact same part as what is found on the 1968 Cougar just a slightly different clips is used for 1969. Cougar part number C8WY-13B008-A.

This listings is for the rubber bump stop used on the headlight housings of the 69 - 70 Cougar. The purpose of this bumper is to stop the eyelids from hitting bare metal when they open up. As the years go by, these bump stops will become heavily indented and may need replacing. There are a few reproductions out there that are "close enough" but so far we haven't found a good match. 1970 has two per side, four per car.  1969 has one per side, two per car. See reference photos above. ...

Here is a time and money saving package deal for the person restoring their 1969 Cougar. This package includes: Hood lip moulding Fender extension mouldings Deck / Trunk lid moulding Six Piece Convertible Windshield Trim Kit Front and Rear Award Winning Bumpers Keep in mind we will often give extra core value trade in for items we may be low on. Please call before sending extra parts for trade value. All parts are show quality. The bumpers are triple plated chrome, the aluminum has the correct...

Here is a time and money saving package deal for the person restoring their 1969 Cougar. This package includes: Hood lip moulding Fender extension mouldings Deck lid moulding Drip rail mouldings Nine piece front and rear window trim Front and rear Award Winning Bumpers Keep in mind we will often give extra core value trade in for items we may be low on. Please call before sending extra parts for trade value. All parts are show quality. The bumpers are triple plated chrome, the aluminum has the...

This bumper bolt is sold individually and replaces Ford part # C4ZB-17758-A. It features the correct "button" head profile covered in stainless steel. Silver zinc with wax coating to extend plating life. Reduced shoulder height allows the nut to seat properly.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more...

This is a complete kit for front and rear. If you own a 71 - 73 and then you will need two more bolts. mercurycougar.net: I was in Salem on business Monday when I decided to give West Coast Classic Cougar a call. Don was gone but Lin was there, talk about a nice guy I looked around the shop and Lin got me the parts I needed for my 68 Coupe. I am sure Lin was busy but he took the time to answer any questions I had, swapped a few stories and gave me a real good deal. I recommend anyone needing...

C9WY-17767-A Front bumper mounting arm, 1969 Mercury Cougar driver side. This will work fine on 1970 Cougars, but technically the 1970 bracket has a rectangular hole for a anti rattle piece of rubber for the stone guard.

C9WY-17766-A Front bumper mounting arm, 1969 Mercury Cougar passenger side. This will work fine on 1970 Cougars, but technically the 1970 bracket has a rectangular hole for a anti rattle piece of rubber for the stone guard.

C9WY-17755-A Front bumper mounting bracket, 1969-70 Mercury Cougar driver side.

C9WY-17A750-A Sold individually, two required per car. Right is the same as left. These Western rear bumper brackets are not heavily rusted, the threads are in perfect shape and they are not bent.

Replaces Ford part #C9WY-16B554/5. Good quality part made with correct type of rubber. Sold as pair only.

This optional used front bumper guard was unique to the 1969-70 Mercury Cougar. These are sold individually and the passenger side (right hand) is the same as the driver side (left hand). The chrome plating was pretty low quality back n the day and these will have some scratches and pitting as they are and almost 50 year old original part. These are rather rare so we put a high value on our cores. Ford part # C9WY-17996-A. Check out this video ...

This optional front bumper guard was unique to the 1969-70 Mercury Cougar. These are sold individually and the passenger side (right hand) is the same as the driver side (left hand). Show quality, better than NOS. These are rather rare so they each carry a $125 core charge. Ford part Number: C9WY-17996-A. Check out this video ...

C9AZ-13A164-B Inner grille bushing, where the hidden headlight hinge pivots. Hole size is 3/4", shaft size is 1/2". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights.

Used outer bushing for the hinge pivots for the hide-away headlights on the Mercury Cougar. Hole size is 5/8", shaft size is 3/8". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights. Ford part # C9AZ-13A164-A. ...

Hardware for mounting the hood bumpers on the radiator core support. Clip mounts with threads down, nut on top. Sold as a Kit as Pictured.

C9AZ-13B013-A Center section that connects to the vacuum motor on many 1969 Ford and Mercury cars with vacuum covered headlights. 1969 Mercury Cougar including XR7 and Eliminator. The center piece is offset to the left of center and the hook part that goes to the vacuum motor points down. 1969 and 1970 center shafts are not interchangeable. 1969 Ford LTD 1969 Galaxie and Galaxie XL 1969 Country Squire Wagons 1969 Mercury Marquis 1969 Mercury Brougham 1969 Marauder and X-100 1969 Colony Park...

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This check valve is located in-line just behind your carburetor. To test it simply place it in your lips and try blowing through the side with the single port. You should be able to breath in and not breath out. If this valve is bad you will find the headlights opening up after the engine has been shut off on your 1969 - 1970 Cougars and your tilt away function not working correctly on your 1967 - 1970 Cougars equipped with a tilt column. A good working vacuum system should be able to...

Reproduction clip for attaching the 1969 front fender extension moulding / trim and the 1970 hood moulding / trim found on the Mercury Cougar. The 1969 application calls for 2 of these clips along with 1 larger clip per side. If you need the larger clip for the 1969 front fender extension moulding / trim, you can get'em right here. The hood lip brightwork for the 1970 requires 4 per side.  *NOTE* The threaded stud on this clip is a little longer than the original ones. This...

Used front fender extension moulding / trim clip for the Mercury Cougar. This is the largest of the three clips required to attach the aluminum 1969 fender moulding / trim to the extension. One is used on each side at the tail (larger part) of the trim piece. This unit is for the purest. If originality is not as important to you, you can get the inexpensive reproduction here.

Used clip for attaching the front fender extension moulding / trim on the Mercury Cougar. The fender extension moulding / trim is sometimes called the eyebrow moulding / trim. This piece of brightwork requires a total of 3 attaching clips, 2 smaller clips and one larger. If you need the larger clip, you can get'em right here! This used original clip is for the purest who values originality. If originality is not an issue, you can get our inexpensive reproduction clip here and save a...

Reproduction large moulding / trim clip for the rear quarter extensions and front fender extensions on the Mercury Cougar. The molding / trim on the 1967-68 rear quarter extension and 1969 front fender extension both require 2 different sizes of clips to properly hold them in place. For the 1967 and 1968 rear quarter extensions, you will need one of these large clips and 1 smaller clip per side. For the 1969 Cougar you will need 1 of these larger clips along with 2 smaller clips per side. This...

Reproduction clip for attaching the hood lip moulding / trim on the Mercury Cougar and six are required. We do offer good used originals here for the purest, but these will work great at half the cost.