Exhaust

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Band or ring style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Comes with a course sheet metal type threaded hex head bolt. Ford part number C5DA-5A272-B. *Note all 1967 & 1968 Cougars had 2 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C6AA-5A272-A is the factory style 2-1/4" tailpipe clamp.

Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford.   Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp and correct style of nuts. Used on all 1968 - 1971 models with 2-1/4" exhaust. Correct for Boss 302, Boss 429, Shelby Mustang, all Ford with 2-1/4 inch exhaust at the H - Pipe.  Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1967 - 1973 models with 2" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Many of the stock exhaust systems were actually 2 inches. Most reproduction "Systems" are 2-1/4, use accordingly. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Reproduction dual exhaust tip to hanger clamp for the 1967 - 1970 Mercury Cougar and Ford Mustang.

Reproduction pair of exhaust pipe clamps for your 67 - 69 Cougar or Mustang.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 351 Windsor engines 1969-70, 351C-2V  and 351C-4V (Cleveland) from 1970-73 Mercury Cougar and Ford Mustang.Fits between exhaust manifold and header pipe (H or Y pipe) 2-1/8 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H and Y pipes. Replaces Ford part number C8AZ-9450-B.

Concours correct engine pipe donut, metal, factory original dual sized design to properly seal H-pipe to Exhaust manifolds MCA approved, sold individually.Replaces Ford Part # C8LV-9450-AFits between exhaust manifold and header pipe (H or Y pipe) 2 1/16 id 3 5/8 od cast iron, tapered top and bottom, smooth inside.Note! These are very difficult to seat compared to the pliable ones we sell. If you do decide to use the steel version it is recommended you apply a liberal coating of Permatex High...

Exhaust manifold flange rings or 'doughnuts' for stock cast iron 428CJ exhaust manifolds. These are the malleable type that conform and slightly crush. Inside diameter just over 2-1/8 inches. Sold individually, two needed per car.

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from an original 1969 M code 351W equipped Cougar. Works for both M and H code Cougars systems. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have...

This oversized 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from original 1969 Cougars equipped with the 390 engine. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that...

This 2 inch dual exhaust system is manufactured right here in the good old USA from an original 1969 S code Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from an original 1969 R code Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original...

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from original 1969-70 G code Cougar Eliminators. This direct replacement system includes: 1 H pipe at 2-1/2 inches, 2 intermediate pipes at 2-1/4 inches, 2 mufflers at 2-1/4 inches, and a right and left tail pipe each at 2-1/4 inches. The system is constructed from 2-1/2 and 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1969 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1969 Cougar and Mustang with the 390 engine. We also sell this H pipe in a 2 inch diameter and have OEM style dual exhaust systems that include the H pipe,...

C9OE-9431-B 351W factory original cast iron exhaust manifold for driver side. For all 1969 and 1970 Windsor 351's.

C9OE-9430-B 351W factory original cast iron exhaust manifold for passenger side. For all 1969 and 1970 Windsor 351's. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay...

C6OE-9428-A 390-4V factory original cast iron exhaust manifold for passenger side. 1969 390-4V IP only. Same as earlier versions, but with a 1969 date and chamfered opening for donut. No spacer needed.

C8OE-9430-D 428 Cobra Jet factory original cast iron exhaust manifold for passenger side. *Spacer required for installation.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. NOTE: Dwayne from "The Brothers Car Collection" clued us in to the fact that the choke tube fitting on the passenger side is indexed 180 degrees off on some sets we sell. Fortunately you can carefully spin it around with vise grips so the opening faces...

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. These manifolds are available in both early and late versions. The earlier version manifold has the correct spacer on the right side while the later version manifold does not.  Installs easily and eliminates clearance issues compared to headers....

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

This reproduction 2" Tri-Y H pipe to be used with the Patriot style headers on your 1969 Cougar or Mustang.

This reproduction 2" Tri-Y H pipe to be used with the Scott Drake style headers on your 1969 Cougar or Mustang.

This direct replacement is the 2-1/4 inch H pipe only and is for any 1969-70 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1969-70 Cougars and Mustangs with the 351W engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Cleveland engines. Please allow 2 - 3 weeks for delivery. ...

This direct replacement is the 2 inch H pipe only and is for any 1969 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1969 Cougar and Mustang with the 390 engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1968-69 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1968-69 Cougars and Mustangs with the 428CJ engine. We also sell this H pipe in a 2-1/2 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for...

This direct replacement features a larger than stock diameter of 2-1/2 inches for increased performance. This is the H pipe only and is for any 1968-69 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from original 1968-69 Cougars and Mustangs with the 428CJ engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the...

This direct replacement is the 2-1/2 inch H pipe only and is for any 1969-70 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from an original 1970 Cougar Eliminator and Boss Mustang  with the G code Boss 302 engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

For all H code 351-2V engine codes with singles exhaust. Includes 1970 351C or Cleveland engines. Holds the rear of the muffler to the passenger side underside body. Ford part number C9WY-5260-A.

Good used tail pipe hanger with decent rubber still attached. Mounts to the frame on the right side of the fuel tank. Supports and holds the rear of the tailpipe stationary. All 1968 - 1970 dual and single exhaust Cougars, all engines. 1970 differs in that the tail pipe clamp was spot welded to the hanger. When you look closely on the 1970 version you will see that there is an alignment hole in the bracket and an alignment tab on the clamp. Also the 1970 version had a less pronounced gusset at...

For all H code 351-2V engine codes with single exhaust. Includes 1970 351C or 351W engines. Includes one tail pipe hanger and one muffler hanger, both of which mount to the passenger side of the car.

Reproduction Concours Correct muffler hangers for your 1968 - 1970 Mercury Cougar.

Muffler mounting tabs for using factory Ford muffler hangers on aftermarket turbo style exhaust mufflers. These help achieve that concours look using a replacement muffler or mufflers. We recommend using your existing horse shoe shaped muffler hanger as a jig for locating these tabs prior to welding. These were copied from the original style tabs found on most 1968-73 Mercury Cougar and Ford Mustangs. 1967 cars and some Mustangs used a single transverse muffler behind the rear axles, these may...

*NOTE: This item comes un-painted from the manufacturer.Very correct reproduction of an impossible to find part. The only difference I can detect is that this original weighs just an ounce or two more than the original. Click on images to enlarge. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the...

Since we have a difficult time keeping grade "A" Windsor heat shields in stock we also offer a driver quality version. This unit will be very thin from rust in certain areas. C9OZ-9A603-A Metal shroud and tube assembly that attaches to the factory 1968-1969 air cleaner assembly on all 351 Windsor engines both H code 351-2V and M code 351W-4V (1969 offering only). *Note - for 1970 this shield is used after build date of 2-2-1970, but could be used on prior dates. We suspect that the early 2...

*NOTE: This item comes un-painted from the manufacturer.Another spot on reproduction! Correct for CJ and SCJ.  Comes with brackets and hardware as shown. Click on images to enlarge. ...

Reproduction hex screw for exhaust pipe clamps for the 1967 - 1973 Mercury Cougar and Ford Mustang. 5/16 x 1-1/2 screw. Fits original and new clamps.

Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.

Reproduction Exhaust Manifold Pipe Stud Kit for the 260, 289, 302, 351 and 1969 390GT 1967 - 1972 Mercury Cougar and Ford Mustang

Kit has the longer studs for use with spacers or butterfly spacers, between 390 and 428CJ passenger side exhaust manifolds and H pipe flange.

This rear segment exhaust system is manufactured right here in the good old USA from original 1968 and 1969 Mercury Cougars. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

This 2-1/4 inch rear segment exhaust system is manufactured right here in the good old USA from an original 1969 M code Cougar. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...