Exhaust

This 2-1/4 rear segment exhaust system is manufactured right here in the good old USA from an original 1969 R code Cougar. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Reproduction 428 Cobra Jet Exhaust Manifold Spacer 1968 - 1970 Mercury Cougar, Ford Mustang, Shelby and Torino Repro

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 

OEM Style Universal Exhaust Hanger Bracket 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1969-70 Mercury Cougar or Ford Mustang equipped with the 351W engine with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351W 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351...

Band or ring style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Comes with a course sheet metal type hex head bolt. Ford part number C6AA-5A272-A. *Not all 1969 & 1970 Cougars had 2-1/4 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C5DA-5A272-B is the factory style 2" tailpipe clamp.

C7OE-9431-A Factory original cast iron exhaust manifold for driver side. 1967, 1968, and 1969 390/427 left side manifold remained unchanged for all three years. Includes 1968 X code 390-2V Premium fuel cars. Click on images to enlarge. ...

Factory cast iron exhaust manifold set, both a correct right C6OE-9428-A and left C7OE-9431-A side matching exhaust manifolds. With 1969 dates. *TRIVIA* 1969 390 S code Cougars were not technically the 390GT variety. An Autolite 4300 carburetor and a non-GT intake manifold changed the designation to 390IP for "Improved Performance."

C8OE-9431-B 428 Cobra Jet factory original cast iron exhaust manifold for driver side. For all 1969-1970 428CJ Cougars after 9/2/1968 build date.

C9ZE-9431-A Factory original cast iron exhaust manifold for driver side. Correct for all Boss 302 Eliminators 1969 and 1970.

C9ZE-9428-A Factory original cast iron exhaust manifold for passenger side. Correct for all Boss 302 Eliminators 1969 and 1970. Nice piece from a CA car, no damage or pitting.

351 Windsor factory cast iron exhaust manifold set, both a correct right C9OE-9430-B and left C9OE-9431-B side matching exhaust manifolds. Same manifolds used on all 351 Windsor engines in 1969 and 1970.  No extra charge to look for a date coded pair but no promise we can hit it spot on either.  

428 Cobra Jet factory cast iron exhaust manifold set, both a correct right C8OE-9430-D and left C8OE-9431-B side matching exhaust manifolds.

Factory cast iron exhaust manifold set, both a correct right C9ZE-9428-A and left C9ZE-9431-A side matching exhaust manifolds. 1969 and 1970 Boss2 Eliminators

This is the harder to find tail pipe hanger as it was only used on dual exhaust cars. Will have usable but cracked rubber. Mounts to the frame on the left side of the fuel tank. Supports and holds the rear of the tailpipe stationary. All 1968 - 1969 dual exhaust Cougars, all engines. Ford part number C8WY-5260-B.

Mounts to the rear of a 'turbo' style muffler. Left side bracket. 351W, 351C, 390, Boss 302, 428CJ - all with dual exhausts. Ford part number C9WY-5260-B.

Mounts to the rear of a 'turbo' style muffler. Right side bracket. 351W, 351C, 390, Boss 302, 428CJ - all with dual exhausts. Ford part number C9WY-5260-C.

Includes the two muffler hangers and two tail pipe hangers. Will not be overly rusty and will have decent rubber still intact. This set is for any 1969 Cougar equipped with factory equipped dual exhaust.

Used original heat riser / S tube for 1968, 1969, and 1970 Cougar and Mustang 428 Cobra Jet / Super Cobra Jet. These will seldom be available. The one pictured above is the best example we've ever seen - removed from the car in 1969 just days after purchase. The pictures below are a more realistic example of the used condition you might expect. There are also additional comparison shots next to the reproduction S tube we also sell. The differences are small but the most obvious is the fact...

Used grade "A" heat shield for the Mercury Cougar or Ford Mustang equipped with either the H code 2V or M code 4V 351 Windsor engine. This metal shroud and tube assembly attaches to the factory air cleaner assembly and really finishes off the engine bay. Ford part # C9OZ-9A603-A.*NOTE* For 1970, this shield was used after the build date of 2/2/1970, but it can also be used on prior dates. We suspect that the early 2 piece shroud was discontinued because of rattling noises or some...

This two piece heat shield has a very narrow application in that it is a one year only item and only for the 390 IP (Improved Performance). It does not mate to metal a "S" shaped heat riser tube but rather a flexible paper-foil tube that attaches to a reducer on the bottom side of the snorkel. Very hard to find item, harder yet to find one that has not rusted out. The unit shown is "tender" in a couple of spots. The lower section carries a Ford part number of C9OZ-9A603-D and the upper section...

C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.

Ford part number C9ZZ-9A603-C for the upper section and C9ZZ-9A603-D for the lower for this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this lower section also. metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this upper section also.

Reproduction intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Used intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

OEM Style Transverse Resonator Exhaust Hanger 1967, 1968 and 1969 Mercury Cougar and Ford Mustang