1969 Mercury Cougar

A quality reproduction black vinyl top that looks and fits great. This top has the correct pattern, however the finish is a bit shinny and will not look original to the discriminating eye. This top will also have a seam in the A pillar.

High quality reproduction black vinyl top for the Mercury Cougar equipped with a factory sunroof that features both the correct pattern and finish. This concours correct top also features a durable moisture resistant backing that will look better and last longer than our economy priced version. This unit is for the Cougar owner who demands premium correct parts for his or her prized feline.Thinking about installing this unit yourself? Check out our video below for some inspiration. ...

High quality reproduction white vinyl top for the Mercury Cougar that features both the correct pattern and finish. This concours correct top also features a durable moisture resistant backing that will look better and last longer than our economy priced version. This unit is for the Cougar owner who demands premium correct parts for his or her prized feline. Thinking about installing this unit yourself? Check out our video below for some inspiration. Below are some comparison shots to show...

High quality reproduction white vinyl top for the Mercury Cougar with sunroof that features both the correct pattern and finish. This top features a durable moisture resistant backing that will look good and last long.  Thinking about installing this unit yourself? Check out our video below for some inspiration. Below are some comparison shots to show the different textures of vinyl tops, including an original 1967 vinyl top for reference. We currently do not carry the...

These are original amp meters converted from reading amps to reading volts. Includes new matching XR7 overlay made from top quality 3M 467MP and use 200MP adhesive. The longer 200MP adhesive is in place the stronger it binds. Optional Volt decal is included. Click here for a article describing the advantages of a Volt Meter. Check out the video below on our new gauge tester: ...

Electronic voltage regulator for use on any 1967-73 Mercury Cougar or Ford Mustang or Ford. Same foot print as originals, cover can be swapped.

We cannot provide new units anymore but we do stand behind this used unit for 30 days.Check out the video below on our new gauge tester: ...

New old stock NOS instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator until it is properly grounded, otherwise it...

This is the cover only. Great for those wanting to use a reliable modern solid state regulator but look concours. Comes with rivets.Replaces Ford part number C8FT-10316-A (cover only)* - Also came on some 70-71 A/C Cars

Voltage regulator for the 1968, 1969, and 1970 manufactured before 9/15/1969 that is not equipped with factory AC. This regulator has "C8AF-10316-A" printed on to it, actual Ford Part number is C3SZ-10316-B or D4TZ-10316-A. This is Ford Regulator Number GR-341. These new voltage regulators are improved and more reliable than the units we've sold previously.

This is the cover only. Great for those wanting to use a reliable modern solid state regulator but look concours. Comes with rivets.Replaces Ford part number C8AF-10316-A (cover only)

Used until early 1970 on vehicles not equipt with Air Conditioning. Decal Text: AUTOLITE REGULATOR 15V C8AF-10316-A NEG

Features the proper cover and original logos. I A S F stamped on cover.Replaces Ford Part #: C8TF-10316-A.* - Also came on some 70-71 A/C CarsThese new voltage regulators are improved and more reliable than the units we've sold previously.

This is the correct size walking cat decal for your eyelid door on the 1967 - 1969 Cougar. It has the studs in the exact place as the originals. You will need this emblem when changing out our 1967 - 1969 background decals as you will have to break the original studs to remove the cat. Also great for those custom applications! Emblem is approx 3 3/4" wide by 1 1/4" tall. This cat does come with two flat attaching clips. *Customer Feedback* Hey Don and Lin, Just wanted to send a couple pictures...

NOS 41" x 24" Walking Cat nylon banner / flag. These were hung up around dealers back in the sixties and early seventies. We're calling it a banner, but the 2 holes on one side of it indicates it may also be a flag.   NOTE* The reflectiveness of the nylon made it a bit difficult to photograph, just know that the banner is in fact white! This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually...

This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...

Warning light panel from a 1969 or 1970 Eliminator model Mercury Cougar. This is a modified light panel for the center of the dash. We mill out the raised portion of the bezel where the lights are framed. We mill flat the panel so that the reproduction block off plate can be attached flush with the panel. Eliminator block off plate sold separately. Ford part number C9WY-10C854-B.

Warning light panel from a 1969 Standard model Mercury Cougar. This is the light panel in the center of the dash. There are three visual check items that light up, 'PARK', 'LOW FUEL', and 'DOOR AJAR'. Specify the color of rubber in the comments or notes. Keep in mind that most of the colors fade or change colors due to UV light and age. Also realize that the rubber trim has shrunken, and may have poor fitment. Plan on dying the rubber trim and re-gluing it to this chrome panel. The 1970 panel...

Reproduction washer for the interlock on all top loader 4 speed transmissions as found on 1967-69 Mercury Cougar and Ford Mustangs.Ford part number C5ZZ-7C318-A.

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.

Used rubber washer for the locking pawl cable to cable guide used for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This unit fits against the cable side of the ninety degree angle. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts...

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

These new taillight mounting washers are sold individually for your Mercury Cougar. Normally installed with a dollop of black goo for sealing out moisture. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Direct aluminum replacement for small block 1967 - 1969 cast iron pumps. Probably the last water pump you'll ever buy. Built to cool better and last longer than any other pump. Features state of the art high efficiency impeller with 16 veins and NASCAR roller type bearing. Race proven for reliability and performance. Includes Gasket. Several other websites state that there was a mid-year change in 1969 Cougar's with a 351W, but all the documentation we have and the cars we have on hand...

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-A. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-J. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8OE-D. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

Cast Iron Water Pump for the 1967, 1968 and 1969 small block. Has six vanes on the impeller. Includes Gasket. Several other websites state that there was a mid-year change in 1969 Cougar's with a 351W, but all the documentation we have and the cars we have on hand all indicate that this change took place at the very beginning of the 70 production year so that the 351C and 351W would use the same water pump. Replaces Ford Part #: D3UZ-8501-A or C5OZ-8501. ...

Light duty OEM Replacement cast iron water pump for any Ford FE 390 / 427 / or 428CJ. Gaskets included. No Core required Replaces Ford Part #: C8AZ-8501-A.

0D13  April 13, 1970 dated.  Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C9AE-8505-A. Found on many Ford 390 and 428CJ engines from 1969-70. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

This concours correct reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This Daniel Carpenter manufactured unit is made of slightly less dense material than the Midland unit, .75lb as compared to .85lb.We have included a few comparison pictures so that you can make an informed decision. Sold as a pair and includes the metal...

This offshore reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This overseas reproduction sold by Daniel Carpenter is simply another option to the US made version, and has been known to fit better than the US made weatherstrips.  Sold as a pair and includes the metal fasteners. Replaces Ford part #...

Reproduction door glass to roof weatherstripping for the Mercury Cougar and Ford mustang. These units are sold as a pair and are also known as the roof rail weatherstrip. Replaces Ford part # C9ZZ-6551222. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Rubber quarter window to door glass seal. Passenger side 1969 Mercury Cougar and convertible, and 1969 Mustang hardtop coupe and convertible. Ford part # C9ZZ-65214A14-A. *NOTE* Will not fit Mustang fastback or Mach 1. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! Check out this video ...

Correct for Coupe and Convertible, Mustang and Cougar. This vertical weather strip slides into the stainless steel strip that attaches to the back side of your left hand door glass. These cost a couple of dollars more than some you will see but are substantially better fitting than the budget version. Replaces Ford part # C9ZZ-65214A15-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video...

Correct for Coupe and Convertible, Mustang and Cougar. This vertical weather strip slides into the stainless steel strip that attaches to the back side of your right hand door glass. These cost a couple of dollars more than some you will see but are substantially better fitting than the budget version. Replaces Ford part # C9ZZ-65214A14-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video...

You will need new window gaskets if you plan on changing the headliner. Replaces Ford part #: C9WY-6542084. Installing it yourself? bedding compound is required for a complete seal.Here are some useful tips on installing this seal made by DCMR.From KTL Restorations; Our cure for installing this less than perfect fitting reproduction is to use the longer trim clips (black ones). The clips Ford used were red oxide and the reproduction clips are green. The black clips extend up about 3/32 of an...

This kit is easier to install than you may think! Five piece kit, comes with installation instructions. Be aware, the seals at the top of the glass do not line up perfectly leaving a gap on the quarter glass top seal. We are working on a solution.  Replaces Ford part # C9ZZ-7653986. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! Check out this...