1969 Mercury Cougar

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 351 Windsor engines 1969-70, 351C-2V  and 351C-4V (Cleveland) from 1970-73 Mercury Cougar and Ford Mustang.Fits between exhaust manifold and header pipe (H or Y pipe) 2-1/8 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H and Y pipes. Replaces Ford part number C8AZ-9450-B.

Concours correct engine pipe donut, metal, factory original dual sized design to properly seal H-pipe to Exhaust manifolds MCA approved, sold individually.Replaces Ford Part # C8LV-9450-AFits between exhaust manifold and header pipe (H or Y pipe) 2 1/16 id 3 5/8 od cast iron, tapered top and bottom, smooth inside.Note! These are very difficult to seat compared to the pliable ones we sell. If you do decide to use the steel version it is recommended you apply a liberal coating of Permatex High...

Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.

Air inlet damper door for any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1967-68 door, but with two small notches, instead of one. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare...

Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...

Used door / lid for the glove box in the Mercury Cougar or Ford Mustang. This unit is just the bare door / lid and does not come with the hinge, liner, lock or lock bezel. Dent free, may have minor surface rust. Ford part # C9ZZ-6506024-A.

Replaces Ford Part #C7AZ-6243629-A. Not used on 1967-78 trunk locks.

Passenger side power window door and main harness from a 1969 Mercury Cougar and 1970 built before 2/2/1970. Tested and inspected and ready to install. Does not fit late 1970 cars.  Ford part number C9WB-14630 Product Condition Grades Below is a general description of what the criteria is for our product condition grades. These are generalizations that are intended to give you an idea of the condition of the product at a quick glance. Because different parts degrade at different...

Used door courtesy light lens on the 67 - 70 Cougar. Because of the heat and placement of the bulb behind this lens, they were prone to burning or in some cases melting. This lens is easily replaceable by removing the two screws holding the housing together and grinding off the studs holding the lens and reflector in place. You can secure them back in place with small amount of epoxy. You can also find the reflector lens here. Right is same as left, sold individually. ...

Used door courtesy light reflector used on 67 - 70 Cougars. This lens is easily replaceable by removing the two screws holding the housing together and grinding off the studs holding the lens and reflector in place. You can secure them back in place with small amount of epoxy. You can also find the light lens here. Right is same as left, sold individually.

Reproduction driver side (left hand) clear door glass for the Mercury Cougar or Ford Mustang. This item does not include with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the...

Used passenger side (right hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. This glue in style door glass will not work in place of the bolt in versions found in later 1970 production models. The glue in style glass was carried over from...

Reproduction passenger side (right hand) clear door glass for the Mercury Cougar or Ford Mustang. This item does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the...

Used driver side (left hand) grade "A" clear glue in style door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass and does not include any window trim, so save your for reuse. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a...

Used driver side (left hand) grade "B" clear glue in style door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass and does not come with any of the window trim, so save yours for reuse. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. This glue in style door glass will not work in place of the bolt in versions...

1969 Mercury Cougar and Ford Mustang coupe/convertible Grade A factory tinted glass for the driver side door, it will have the faint green tint and be marked SUN-X. Excellent used door glass with no scratches. Glue-in or bonded design, will not fit early 1970 models.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss, Shelby and Cougar Ford part # C9ZZ-6521401-B. *NOTE* Vertical chrome trim not included. Air...

1969 Mercury Cougar and Ford Mustang coupe/convertible Grade B factory tinted glass for the driver side door, it will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Glue-in or bonded design, will not fit early 1970 models. Ford part # C9ZZ-6521401-B. *NOTE* Vertical chrome trim not included. Air conditioning cars were supposed to have SUN-X tinted glass. Look...

New TINT Driver Side Door Glass for the 1969 Mercury Cougar, glass only. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly...

Reproduction green tinted driver side (left hand) door glass for the Mercury Cougar or Ford Mustang. If your Cougar came with air conditioning, it came with Sun-X green tinted glass.This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly...

1969 Mercury Cougar and Ford Mustang coupe/convertible Grade A factory tinted glass for the passenger side door, it will have the faint green tint and be marked SUN-X. Excellent used door glass with no scratches. Glue-in or bonded design, will not fit early 1970 models.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss, Shelby and Cougar Ford part number C9ZZ-6521400-B. *NOTE* Vertical chrome trim not include. Air...

1969 Mercury Cougar and Ford Mustang coupe/convertible Grade B factory tinted glass for the passenger side door, it will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Glue-in or bonded design, will not fit early 1970 models. Ford part number C9ZZ-6521400-B. *NOTE* Vertical chrome trim not included. Air conditioning cars were supposed to have SUN-X tinted glass....

New TINT Passenger Side Door Glass for the 1969 Mercury Cougar, Glass only.This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In glass? How about how to...

Front bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, passenger side front bracket only. Comes without stud that attaches to window regulator. We also have examples with the stud for a premium price. Here is the 3M product used to glue the glass to the bracket. We also have stud keepers available if you need to reattach your loose stud. Keeper also available for the T stud. We are looking to find someone to manufacture the...

Front bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, passenger side front bracket only. Comes with stud that attaches to window regulator. We also have examples in which the stud is missing for a reduced price. Here is the 3M product used to glue the glass to the bracket. Keeper also available for the T stud. We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford...

Front bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, passenger side front bracket only. Comes without stud that attaches to window regulator. We also have examples with the stud for a premium price. Here is the 3M product used to glue the glass to the bracket. Keeper also available for the T stud. We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford part #...

Front bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, passenger side front bracket only. Comes with stud that attaches to window regulator. We also have examples in which the stud is missing for a reduced price. Here is the 3M product used to glue the glass to the bracket. Keeper also available for the T stud. We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford part #...

Rear bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, driver side rear bracket only. Comes as shown, no cracks, distortions or stripped threads. Here is the 3M product used to glue the glass to the bracket. 1969 glass is glued in approximately 1 inch from the rear edge. 1970 glued in glass is approximately 2-1/4 inches from the straight edge if extended with an imaginary line from the rear edge of glass. Ford part # C9ZB-65223A19-A. "...

Rear bracket for mounting glued in door glass for all 1969 and very early 1970 Mercury Cougar and Ford Mustangs, passenger side rear bracket only. Comes as shown, no cracks, distortions or stripped threads. Here is the 3M product used to glue the glass to the bracket. 1969 glass is glued in approximately 1 inch from the rear edge. 1970 glued in glass is approximately 2-1/4 inches from the straight edge if extended with an imaginary line from the rear edge of glass. Ford part # C9ZB-65223A18-A....

Window guide or 'elevator'. 1969 through early 1970 Mercury Cougar and Ford Mustang door glass. Two guides per door. Sold individually, will have undamaged excellent threads. Ford master part number C9ZZ-65222A56-A. *Note will not have original plastic bushing inserts installed. You will need to reuse your originals or purchase new or used. Please see related items. Ford part # C9ZB-65223A00-A. *NOTE* Excludes 1970 bolt in door glass. Do you have questions about Glue-In vs Bolt-In glass?...

Reproduction door glass run. This is the metal tube that the windows go up and down on, sometimes called an elevator shaft. Left side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Check out our used door glass runs, original Ford and lower priced.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. OK reproduction, but the...

This is one of the metal tubes that the windows go up and down on, sometimes called an elevator shaft. Left side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Sometimes marked with a letter "L", for left.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521547-A. Do you have questions about Glue-In vs Bolt-In glass? How...

Reproduction door glass run. This is the metal tube that the windows go up and down on, sometimes called an elevator shaft. Right side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Check out our used door glass runs, original Ford and lower priced.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521546-A. Do...

This is one of the metal tubes that the windows go up and down on, sometimes called an elevator shaft. Right side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Sometimes marked with a single "R", for right.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521546-A. Do you have questions about Glue-In vs Bolt-In...

Reproduction of the 1969-70 Mercury Cougar XR7 door panel door grab handle or door pull ends and caps. Also found on 1969-70 full sized Mercury cars and 1968-70 Lincoln Continental MK III. Chromed end originally had a Mercury part number of C9MB-5422668-A, and the flat covers had a part number of C8MB-5422678-A. Nice reproduction of the covers, although we feel that they are a tad too shiney. Sold in a set of 8 pieces, enough for two door pulls.

This is a good reproduction of the original Ford part designed to fit Cougars, as well as many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG!Ford part # C6OZ-6222405-A.

New Old Stock part for 1969-70 Mercury Cougars, as well as many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG!  Handle only, no button or hardware with this item. NOS does not necessarily mean perfect chrome. Look at the pictures, item pictured, is the item shipped.Ford part # C6OZ-6222404-A.

This is a good reproduction of the original Ford part designed to fit Cougars, as well as many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG!Ford part # C6OZ-6222404-A.

Complete Chrome Handle and metal bracket with rubber bumper assembled. Exact reproduction ready to bolt on. Replaces Ford Part number C9ZZ-6522601.

Complete Chrome Handle and metal bracket with rubber bumper assembled. Exact reproduction ready to bolt on. Replaces Ford Part number C9ZZ-6522600 on the right and C9ZZ-6522601 on the left.

Complete Chrome Handle and metal bracket with rubber bumper assembled. Exact reproduction ready to bolt on. Replaces Ford Part Number C9ZZ-6522600.

Bulk pack of 100 oval head phillips screws for door and window crank handles.

Made in America using original Ford tooling. No excuses, premium quality part. Right is the same as left.

This used button comes with the original spring and rubber grommet as shown. Our new door handle kits do not come with the spring shown here so if you need these small items to complete your handle assembly this is the listing for you! Also fits Torino, Ranchero.

This quality kit includes gaskets and buttons for both the passenger and driver side. The fit and finish is perfect on these, No excuses here, satisfaction guaranteed. These fit many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Fairlane, Australian Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG! Replaces Ford part numbers C6OZ-6222404-A and C6OZ-6222405-A ...

Our used handles do not come with this linkage part so if yours is missing this is what you need. Comes with mounting screw as shown.

Fits Standard and XR7 Sold as a Set as Pictured.

Replated original door handles from premium western pit free cores. We sell these on an exchange basis but keep in mind we cannot take pitted cores in exchange. Ford Part #: C6OZ-6222404-A  and C6OZ-6222405-A

Most times when your door sags you do not need new hinges but rather pins and bushings. If your holes are reemed or "hogged out" you will need to buy new hinges or our good used hinges that come with new pins and bushings. Sold individually, eight required per car. I.D. 11/32"O.D 7/16" These bushings are not the same as those offered by some of the "Discount Mustang Shops".  Several of the reproductions of this bushing are too large diameter and require you to drill out your hinges...