1969 Mercury Cougar

3M brand windshield to channel adhesive. This is what is used for installing the windshields on 69-73 Cougars and Mustangs

Repro New Clear Windshield for Cougar. Replace that scratched and pitted old glass with the milky top, Our new glass is clear as rain, and works great too! BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate displayed. Keep in mind this is a common windshield that can be picked up locally from most any automotive glass shop....

Used Grade A Windshield Defroster Nozzle for any 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Grade A will be free from physical defects, may have a minor scuff or scratch.Replaces Ford part number C9ZZ-18490-B.

Used Grade B Windshield Defroster Nozzle for any 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Grade B will have a small crack or chip, or possibly a broken mounting tab.Replaces Ford part number C9ZZ-18490-B.

Pair on reproduction lower windshield stops for all 1969-70 Mercury Cougar and Ford Mustangs

These zinc-plated Washer Nozzles are good copies of the originals. 1969 and 1970 Mercury Cougar and Ford Mustangs only. Sold in pairs.Replaces Ford Part C9ZZ-17603-A and D0ZZ-17603.

This excellent reproduction windshield washer bottle includes the Ford logo on the lid ( C9ZZ-17632-A ) and part number C9ZF-17B613 stamped on the top of the bottle exactly like the originals. The tooling was made using the original Ford blueprints and nice original patterns. Blow Molded Plastic. There are two available reproductions

Injection molded high strength plastic connector for hoses leading to nozzles. Factory fit.Replaces Ford Part #: C7SZ-17A601-A or C0AB-17A601-A.Will not fit 69-70 with factory hoses as they used Ford part # C8OZ-17A601-A

NEW DESIGN... The consistency of rubber on these strips is soft and supple now.  The doors do not have to be "slammed"  Of the three reproductions versions out, there these are the best.   If you have any NOS to sell we would like to hear about them.Replaces Ford part #: C9ZZ-7602626

NEW DESIGN... The consistency of rubber on these strips is soft and supple now. The doors do not have to be "slammed" Of the three reproductions versions out there, these are the best. If you have any NOS to sell we would like to hear about them. Replaces Ford part #: C9ZZ-7602627

Satin Finish Wiper Arm

These are hand picked grade A condition original arms with no defects. Right is the same as left. Sold individually, two per car.The reproductions of the 67-70 are identical, but the originals are not the same between years. The 67-68 and the 69-70 were bent at different angles and carry different Trico patent numbers.In our experience in owning and parting 100's of early Cougars, 1967 and 1968 use the early style, and 1969 and 70 use the later style.Click here to see pics of the...

Best replacement for the original wiper blade assembly. Replaces Ford part #: D4AZ-17528 and C9AZ-17528-A. Sold individually

Original Trico stainless wiper holder assembly, removed from a 1970 Mercury Cougar. Fits any 1969-70 Mercury Cougar and Ford Mustang. Has the original metal fastener to connect to your wiper arm, rather than the plastic piece used in the reproductions. Sold individually, two per car, 16" rubber wiper blade not included.*Note - This is NOT, repeat NOT the ultra rare 1969 production wiper blade holder assembly. This is a Trico 16 inch blade holder as found on most 1970 cars.

The hinges on these original arms tend to get worn out which will cause irregular movement and can eventually burn up your wiper motor or bind up the linkage. If your wipers do not move in tandem

Original FoMoCo used two speed windshield wiper motor for your 1969-70 Mercury Cougar or Ford Mustang. This used motor comes with wiring harness with unique grommet for the firewall specific to 1969-70 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1969-70 installation, must be marked 9Z. Linkage arms sold separately. Ford part # C9ZF-17504-C.

A nice reproduction of the standard air cleaner wing nut. This version was used on most Ford products through the 1980's.

Spare Tire Mount Wing Nut Reproduction for the 1968 through 1973 Mercury Cougar / Ford Mustang

For 1968 Ford standardized or changed all of the J-bolt threads to the beefier 1/2"-13. We have noted two variations of this wing nut. The most obvious identifier between the two is the tabs in the center. The majority have these tabs present, the minority do not. We also stock and carry the correct disc or hold down plate, and the J bolt. Lots of sizes and lengths for those. Do you have the correct one?

This is the set of six bolts needed to attach the pivot section of the wiper arms to the cowl on 1969-1970 Cougars and Mustangs. Three bolts needed per side

Used and reusable backup lamp socket and wiring assembly for the reproduction reverse light chrome housings or to replace a damaged lead in your original 1969-70 Mercury Cougar reverse light. This light socket assembly uses the 1156 bulb. NOTE: These sockets are crimped from the factory and are difficult to remove. When re-installing, there won't be much "meat" left to flare out inside the bezel and you may run into issues with getting a good ground. 

Big Block FE 390 or 428 engine feed harness that fits the 1969 or 1970 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C9ZZ-14289-B and D0AZ-14289-A.Check out the video below on our new gauge tester: ...

Reproduction dash to engine gauge feed harness for the Mercury Cougar equipped with the 351 Windsor. All black boot plugs, this is the style used on cars with air conditioning. Fits 1969-70 Mercury Cougar with 351W engines and 1969-70 Ford Mustang with 302 or 351W engines. Check out the video below on our new gauge tester: ...

Reproduction dash to engine gauge feed harness for the Mercury Cougar equipped with the 351 Windsor. All black and yellow boot plugs, this is the style used on cars without air conditioning. Fits 1969-70 Mercury Cougar with 351W engines and 1969-70 Ford Mustang with 302 or 351W engines. Check out the video below on our new gauge tester: ...

Master clip kit which includes following fasteners:Door courtesy and speaker Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorn feedPassenger side apron below relayRadio cable to dashSide marker and headlightsTurn signal lights on hood scoopUnder dashVarious location zip tiesKeep in mind that there are many other fasteners on 1969 Cougars / Mustangs that are not in this kit. ...

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end. Replaces Ford Part #: C9ZB-19A885-B.

Wire harness extension that runs from the under dash harness to the A/C fan control switch on any 69 - 70 Cougar Standard or XR7, or the 69 - 70 Mustang.Ford part number C9ZA-19945-B

Complete 25 piece clip kit for the 1969 Cougar or Mustang. Keep in mind that this is produced as a Mustang clip kit, and although most clips are the same between Mustang and Cougar...not all clips apply to Cougar applications.   

This Screw fastens the plastic guide for turn signal wires next to column under the cone by steering wheel.

Used grade "A" simulated wire spoke hubcap / wheel cover that is in excellent condition with no curb scrapes. This listing is for someone who has removed their center from their current damaged cap and wants to save money by purchasing a cap with no center. The same cap was used on Most all FoMoCo products including but not limited to the Falcon, Mustang, Fairlane, Comet, Galaxie, Montego and LTD, only the center logo changed one car to the next. Ford part # C7WY-1130-C. *NOTE* You will often...

This short harness attaches to the black power wire coming from the starter solenoid and then attaches to the harness that brings the power back to the convertible top pump or power sunroof motor. This harness is for the 1969 XR7 or 1969 Standard and the 1970 Standard but it is not correct for the 1970 XR7 with power sunroof or convertible top as the 1970 XR7 used a rocker switch mounted in the dash pad located above the AC or AC block off plate. *NOTE* Side by side comparisons between 1969...

Preproduction wiring harness, connects the convertible top switch to the pump on both the xr7 and standard model Cougars and Mustang 1969 - 1973 convertibles.

This harness connects the convertible top motor to the under dash convertible top harness under the dash. Fits 1969-70 Mercury Cougar and 1969-70 Ford Mustang. This wire rests in the trough under the passenger side sill plate and goes behind the back seat where the convertible top pump is located.Ford part number C9ZB-15A668-B.

This harness connects the convertible top switch to the pump on both the xr7 and standard 1969 - 1973 convertibles.

This black wire attaches to the fusible link. The Fusible link connects to the starter solenoid with an eyelet connector, then connects to this wire with a billet connector. This wire then passes through the firewall to mate with the power top switch wiring under the dash. Correct for both XR7, Standard convertibles and power sunroof equipped Cougars in 1969, and Standard Cougar Convertibles in 1970.Casting Number: C9ZB-15A669-BFord Part Number: C9ZZ-15A669-BFits: 1969 Mercury Cougar Standard...

Used jumper wire used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reprints of the original Ford manuals. Even if you do not service your own car this may save you some money if you hand it to your mechanic next time he does electrical work on your car...

Used under dash to under hood connector for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.*NOTE*  This connector comes with the bolt and spring.

Used under dash wiring harness fuse block / box (with a chip or two) with wire leads for the Mercury Cougar STANDARD. This is part of the 14401 main under dash wiring harness. The difference between Standard and XR7 is that the Standard block has the pink resistance wire. *Note - The fuse blocks will have a small amount of damage or chips on it, in spite of what is shown in the picture.

Used under dash wiring harness fuse block / box (with a chip or two) with wire leads for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness. The difference between the XR7 and Standard box is that the Standard box has the pink resistance wire.  *Note - The fuse blocks will have a small amount of damage or chips on it, in spite of what is shown in the picture.

Used wiring harness assembly specific to 1969 Mercury Cougar or Ford Mustang with H code 351W-2V or M code 351W-4V engines. Jumper harness about 9-1/2 inches long. Goes between the cowl plug for the engine gauge feed harness, and the engine gauge feed harness. Special with a 2 ohm resistance wire for the temperature gauge / sending unit. We believe that this wire harness was used specifically with the factory installed temperature sending units for 351W engines in 1969. Ford part...

This black wire attaches to the Circuit Breaker coming off the starter solenoid on one end then passes through the firewall to mate with the top switch wiring harness at the other end. We believe that some 1969 harnesses may have used a fusible link wiring harness in place of this one. This harness and the circuit breaker can be used on those applications.Ford part number C9ZB-15A669-B or C9ZZ-15A669-B.

Used wire harness for the 69 - 70 STANDARD Cougar. This main harness connects to the harness for the convenience lights on the warning light panel in the center of the dash. Ford part number C9WY-10C877-C. Used in conjunction with the two convenience light harnesses / sockets found here. The convenience package was offered on Cougars that were non-XR7.

1969-70 Mercury Cougar XR7 wiring harness for the courtesy switch panel in the center of the dash. This is the wiring harness for the switch panel bezels labeled MAP COURTESY PANEL ACCY. The ACCY position does not have a connector on the harness. Pins on the switches need to be mounted so that they are on top for the harness to attach. Blue goes to the MAP switch, white goes to the COURTESY switch, and black goes to the PANEL switch.Ford part number C9WB-10B923-D or C9WY-10B923-B. Clips for...

Reproduction dash to console harness for your 69 - 70 Cougar or Mustang.

Main console wiring harness only, 1969 Mercury Cougar and Ford Mustang. Ford part number C9ZB-15A056-A and C9ZZ-15A056-A. Plugs for cigar lighter, shift indicator or PRNDL light, ashtray wiring harness plug, and heat/AC control. 15A056 harness only, secondary harnesses available separately.

Grade "A" harness that runs from the passenger side door jamb to the courtesy / C-Pillar light. This harness is only needed if you have a Standard model car. NOTE: All XR7's would have already come equipped with his harness.