1969 Mercury Cougar

1969 351-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - All 50 states. C9ZF-C stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1969 351-4V Autolite 4300 carburetor, automatic FMX transmission - All 50 states. C9ZF-D stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1969 428CJ Holley Carburetor - Core 428CJ service replacement carburetor, automatic C6 transmission - all 50 states. C9AF-9510-U stamped on the carburetor air horn. Holley list #4609, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Includes Super Cobra Jet.

1969 428CJ-4V Holley 4150 carburetor, 4 speed manual transmission - all 50 states. C9AF-9510-M stamped on the carburetor air horn. Holley list #4279, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Includes Super Cobra Jet.

1969 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - all 50 states. C9AF-9510-N stamped on the carburetor air horn. Holley list #4280, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Includes Super Cobra Jet.

1969 302-4V Boss Eliminator Holley 4150 carburetor, 4 speed manual transmission - all 50 states. C9ZF-9510-J stamped on the carburetor air horn with a 903 date code. Holley list #4511, 780 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top.

CARBURETOR SPACER PLATE, 0.28" thick, has correct tab marked "FRONT". Replaces Ford Part Number C8AZ-9A589-G

Original Boss 302 carburetor spacer plate, bake-o-lite with metal tube angled to the side. See the link on the Boss 302 website here.Replaces Ford part number C9ZZ-9A589-C.

New carburetor spacer gasket, goes between the intake manifold and spacer plate. 1969 S code 390-4V or 390IP. Upper gasket, spacer plate to carburetor here.

Click on images to enlarge. Give your Cougar the added comfort of a extra 5/8" of Heavy padding under the carpeting and almost 30 lbs of Sound Deadening material. The mass backing gives your carpet the plush feel of the carpeting in a new luxury car while adding a great deal of sound deadener to muffle road noise. The mass backing combined with the foil heat shield (Part # 10330) should provide sound deadening equivalent to that of the factory sound deadener. Of the multiple carpets available...

New Old Stock center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. Called an applique. Used only in 1968 on the one style XR7 hubcap. Not sure why it has a 1969 part number, error? Ford part number C9WY-1137-A.

Set of 4 Chrome center caps with red background and chrome Mercury man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these...

Reproduction chrome spinner cap for the Mercury or Ford that is equipped with Magnum 500 wheels. This cap will also work with any Ford, GM or Mopar Magnum 500 wheel. With a mounting system that is far superior to the original, this unit will definitely give your ride a more aggressive look. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good threadlocker which...

Reproduction chrome spinner center cap for the Mercury Cougar equipped with the magnum 500 wheel. Actually, this unit will work on any Ford, GM or Mopar Magnum wheel. Looks great and the mounting system is far superior to the originals. These look really aggressive.*NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good threadlocker which you can get right here. ...

These original clip on center caps are an inferior design compared to our reproductions that screw on from the back. The originals had varying shades of blue, whereas the repro has a solid blue. The only reason you would purchase this fragile expensive used cap is to match what you currently have on a very original car. When using center caps on Legendary wheels, you will need these adapter plates. Ford part # C9WY-1130-BCheck out our video on Legendary Wheels below: ...

New in-house cut vinyl applique for replacing the burl wood overlay on your 1969 Cougar console insert.

Correct reproduction available only from WCCC. Notice our consoles feature the correct Burl grain xr7 applique and correct for xr7 3 hump lid. Only available in black, we suggest SEM flexible coating if you need to color them to match your interior. We find that custom mixing the paint will get you better results than their off the shelf selections. Inquire with your local Automotive paint supply house.

Headlamp center shaft actuator rod clips. Sold individually, two clips needed, one on each side of the shaft. Not really needed, probably kept the shaft ends from moving during installation. We have found two different sizes of these clips. No pattern between 1969 and 1970.

New old stock check valve for Bendix brake boosters. This is a white plastic check valve. Ford part number D0AZ-2365-A.Check the related items, for a reproduction rubber grommet.

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.

Clamp for supporting and connecting the hard line from the dryer and the suction hose from the condenser.. Two piece clamp with screw. No actual Ford part number listed in the MPC or assembly manuals, the basic part number would be 19B632 though. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

These are used hose clamps that have a tab and fold over on them selves. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available do have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, or straps bundling the hoses on most cars. These clamps should fit a variety of different Ford and Mercury products, not just Mustang and Cougar....

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

Band or ring style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Comes with a course sheet metal type hex head bolt. Ford part number C6AA-5A272-A. *Not all 1969 & 1970 Cougars had 2-1/4 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C5DA-5A272-B is the factory style 2" tailpipe clamp.

Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.

Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...

Correct plastic rocker moulding clips with Ford engineering # C9WB-6510182-A, Ford part #C9WY-6510182-A. There are five of these on each side for a total of ten per car.Fits: 1969 Mercury Cougar1970 Mercury Cougar

Used plastic clip for the Mercury Cougar or Ford Mustang.

Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.

Used Under-dash Wiring Harness Plastic Cover / Clip for the 1969 and 1970 Mercury Cougar or Ford Mustang

Sold as a set of twelve (two more than required), replaces Ford part #C9WY-6510182-A. From the factory there were five of these on each side for a total of ten per car. These same clips were also used on 1977-1979 Mercury Cougars and Thunderbirds. Most likely they were used on other FoMoCo products.Fits: 1969 Mercury Cougar1970 Mercury Cougar

Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...

Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...

New in box original FoMoCo. 1969-70 Standard model Cougars. Part number C9WY-15A000-ACheck out the video below on our new gauge tester: ...

SUPPLIER IS OUT OF STOCK UNTIL MAY 2024 Used in conjunction with Ford fan part # C9ZZ-8600-C that is stamped C9ZE-E. Features a parkerized shaft with an integral mounting flange. The aluminum portions are finished with silver cadmium and are mated together with filister head, Phillips machine screws (8) and an additional crimping operation was used to assemble the front and rear housings. The radial curved spring was originally finished in gold cadmium. This assembly stands 2 5/8" tall when...

C9ZZ-7528-A Equalizer bar or "Z" bar for 351 cubic inch Windsor engines and Boss 302 Eliminators with manual transmissions. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

C9ZZ-7519-B Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

Made of heavy gauge steel with a satin black painted finish. Replaces Ford Part #: C9ZZ-7535-A.

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.

New old stock stainless clutch pedal pad trim. About 1/8 inches wider that the reproduction version. Replaces Ford Part #: C9ZZ-7B544-A.

NOS plastic brackets that screw to your roof and then slide a vinyl colored piece over. Sold individually, two are required per car. Ford part # C8AZ-6229232-A.

NOS white colored coat hooks pair. Reproductions only come in black, these are new in the package. White color started in 1970, off white and parchement 1968-69. Fits 1968-73 Mercury Cougar and Ford everything including that Mustang. Ford Part #: D0AZ-6229024-K.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

New coil spring compressing tool to compress the coil springs of the 1967-73 Mercury Cougar or 1965-73 Ford Mustang. This tool now comes with a bearing to make the job much easier. This spring compressor is a must for safely removing front coil springs. We also offer a 60 Day Loaner if you only need the tool for a short period of time. *NOTE* Not recommended for heavy duty coil springs like found on pickup trucks and full sized cars. ...

Tall version 1" thick and can be used with performance springs to bring the car to a stock ride height. Sold as a Pair. Replaces Ford Part #: C4DZ-5415-A.