1969 Mercury Cougar

This fine threaded Phillips screw assembly is the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The two new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the comparison...

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

Economy Small Block Powering Steering Adjustment Bracket. Lighter weight material than OEM. Replaces Ford Part #: C7SZ-3A732-A.

Perfect fit for your 289, 302, or 351w with or without AC but a hard sell when our good used rust free brackets cost less . . .

Used alternator adjusting bracket for any 1969 Mercury Cougar or Ford Mustang with 351W V-8 engines. This C9OE-10145-A stamped bracket is correct for all H or M code 351 Windsor engines. Will also fit 1969 F code 302 Ford engines too.Ford part number C9OE-10145-A.*Trivia - All 3 small block alternator adjusting brackets from 1965-1969 will fit most all 289 / 302 / 351W engines unless your engine has one of the larger pulleys. ...

Used alternator adjusting bracket for any 390 engine 1968-69 Mercury Cougar or Ford Mustang without factory smog. Specifically this is for 1968 390-2V or X code engines, and 1969 390-4V or 390IP engines offered in 1969 cars with S code designation. Replaces Ford part number C8AE-10145-A.This is the 411 for 1968-69 alternator mounting on Mustang and Cougar with 390 engines. If your 1968 S code car (390GT or 390-4V) was delivered in the United States (meaning not Canada or other foreign...

Application is 1967 - 1968 289/302 and 1969 Boss 302 Eliminator alternator adjusting with factory air injection emissions. Casting number C6OE-10145-A, Ford part number C6OZ-10145-A.

C8AE-9B452-B Thermactor smog pump belt tensioning adjustment bracket. Application is for all 1968 - 1970 FE engines with factory installed thermactor smog systems.

Reproduction thermactor smog pump adjusting bracket for all 1968 Mercury Cougar and 1968 Ford Mustang with S code 390-4V engines. Additionally this bracket was also used on 1968-70 Mercury Cougar and Ford Mustang with 428 Cobra Jet engines. Quality made product. Ford number C8AE-9B452-B.

This high performance alignment kit replaces the factory eccentric bolt and cam that holds the lower control arm to the frame. The eccentric cam is used for setting wheel camber. When the eccentric is turned, the lower arm moves in or out changing camber. Stock eccentric cams can slip or rotate going over bumps, allowing the alignment to change. Which is the cause of many worn tires. The lower control arm adjusting cam eliminator kit replaces the eccentric bolt and cam with non slipping...

Sleeve and hardware for joining the inner and outer tie rods together. This also is a 'toe in' adjustment part. Sold individually, two needed per car. Replaces Ford Part #: C2AA-3310-A

Set of 8 1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples. Also sold individually.

1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples.Also sold in a set of 8. ...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

C8OA-3B236-A Complete lower control arm cam and attaching bolt. 4 pieces included - Cam/bolt, lower cam, nut and lock washer. We offer this used front suspension lower control arm adjusting cam from rust free Western States cars. These are MUCH better quality than any of the stock "looking" reproductions offered. For use on all 1967 - 1973 Mercury Cougar and Ford Mustangs. Part of the C6OZ-3048-A lower arm mounting kit. Bolt/cam part number C8OA-3B236-A, secondary cam part...

This air cleaner assembly never came from the factory on any Cougar, but was an over the counter option available from your Ford dealer. If you have a very nice hood blanket I would think twice before using it in conjunction with this air cleaner assembly as it will leave an imprint. To avoid this problem with small block cars you can use a lower profile carburetor spacer, but on big block cars this is not an option due to the already thin design of the factory carburetor spacer. This will...

Reproduction Group II customizable oval air cleaner with the optional "Walking Cat" for your Mercury Cougar. Good quality reproduction that will go nicely with our Cougar aluminum valve covers. The finish on the black portion is not the same as the crinkle finish on the valve covers but do know the crinkle finish can be added with an aerosol product found from most paint suppliers. If you are using a vented oil filler cap you will need to drill a hole in the base to insert the rubber...

This 'Cal Custom' style 14" Air Cleaner Assembly looks great and really compliments our new matching oil pan and valve covers. These covers offer a true "old school" look. Clean look with no visible mounting nut. Lid has a 1/4x20 nut attached on the bottom side (requires shortening carburetor stud). Kit includes aluminum finned top, air filter, and bottom plate.

Quality reproduction of the 1968 - 1970 CJ Mercury Cougar, 1969 - 1970 Shelby GT500, 1968 - 1969 Cyclone, Ford Fairlane, Ranchero and Torino 428 Cobra Jet Ram Air cleaner base. Features correct snorkel opening and breather elbow.Replaces Ford part number C9ZZ-9600-E or C8ZZ-9600-A.

Brand new exact reproduction of the 1969 Q-Code 428 Cobra Jet non-shaker air cleaner base. Works for Cougars, Mustangs and Fairlanes. Correct snorkel opening, breather port, three mounting studs and a port for the vacuum powered air inlet door. Sold as a stand alone base, does not include snorkel,vacuum motor and door.Ford part number C9ZZ-9600-H 

Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)

Reproduction carburetor stud for all Ford numbered Holley carburetors 1967-71. 1/4-20 double ended stud from AMK. Stud only, no wingnut. 

This is a reproduction of the original Autolite parts decal that was located on the air cleaner.Fits the following models with a BOSS 302 or a 428 4 barrel Cobra Jet engine:1969 Cougar1969 Mustang

This is a reproduction of the original engine displacement decal. Yellow background with black logo followed by black background with white 302 4V followed by yellow background with black BOSS. Located on the top of the air cleaner.Fits the following models with a BOSS 302 engine:1969 Cougar1969 Mustang

Replacement air filter for the 1967 - 1973 Mercury Cougar 14" 'Cal Custom' Aluminum Finned Air Cleaner Assembly.

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Complete heater and air conditioning control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic chrome knobs and lever borders. Does not include the indicator light plug and harness. Knobs, if included may not be in the greatest shape. We suggest purchasing the new reproduction knobs. Ford part # C9ZZ-19A884-A. *Restoration Tip* For...

Reproduction air conditioning dryer decal for the 1969 Mercury Cougar or Ford Mustang

This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. * This filter fits primarily Big Block cars, but a couple of other combinations, so grab a tape measure and double check the height of the one you need to replace, as that will tell you which one you need. Air Filter Height (Inches) : 2.193" Air Filter Height (mm) : 55.7 mm  Air Filter Bottom I.D. (Inches) : 11.32" Air Filter Bottom I.D. (mm) : 287.53 mm Air Filter...

These filters feature the correct color of filter paper and an red/orange molded face. In addition, they have the correct "round hole" design on the outer shell. Fits Mustang 1965-67 K code HiPo 289 and 1968 Mercury Cougar GT-E W code 427-4V engines, that were originally equipped with the chrome high performance air filter assemblies. Please note: this filter will NOT fit a standard Ford air cleaner Replaces Ford Part #: B7SZ-9601-A. ...

Correct dimensions, good fit. Will show minor cracks in rubber but will not affect performance and cannot be seen when installed. Replacement air cleaner for the 1967 - 1973 Mercury Cougar Walking Cat Oval Air Cleaner, as well as other Ford oval air cleaners.

This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. Please note that the Ford Service Replacement specs for this filter (Service Replacement # D7AF9601AA) are; Type: 67; Inside: 13.000; Outside: 11.200; Height: 2.795. All reproductions that we have found follow these specs, making the filter 1/8" taller than the original filters. These filters will function properly, but the lid will not seat properly. ACTUAL FILTER SPECS: Air Filter Height (Inches) : 2.822...

Common air pump for all 1968 - 1970 thermactor emissions systems. 1968 289-2V, 302-2V, and 302-4V all with manual transmissions, and 1968 390-4V, 427-4V all domestic US Cougars. Additionally all 1968 - 1970 428 Cobra Jets, and 1969 - 1970 Boss 302 Eliminators. Identified by the use of 3 attaching bolts for the drive pulley, a white colored cooling fan, and a round pressure relief valve on the side of the pump. Later pumps do not have this pressure relief valve. Good used thermactor smog air...

Common air pump for all 1968 - 1970 thermactor emissions systems. 1968 289-2V, 302-2V, and 302-4V all with manual transmissions, and 1968 390-4V, 427-4V all domestic US Cougars. Additionally all 1968 - 1970 428 Cobra Jets, and 1969 - 1970 Boss 302 Eliminators. Identified by the use of 3 attaching bolts for the drive pulley, a white colored cooling fan, and a round pressure relief valve on the side of the pump. Later pumps do not have this pressure relief valve. Current date: 7J231   ...

This 1965 Mustang alignment pin is not correct for the 1969 to 1973 Cougar but it will work. See the image to the left to see the comparison to an original 69 pin.

Remanufactured alternator for any 67 - 73 Cougar or Mustang. Specs: Rated at 55 ampsSingle V groove pulleyExternal fanPlug position at 5 o'clock

Nice American made reproduction bracket. Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines, all with Thermactor smog pumps. This is also referred to as the low mount alternator mounting bracket. It has the Ford stamped casting number of C8AE-10156-A. Ford engineering number is C8AZ-10156-A.

Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines. This is also referred to as the low mount alternator mounting bracket. It has the Ford stamped casting number of C8AE-10156-A. Ford engineering number is C8AZ-10156-A.

Reproduction Alternator Connection Nut for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold insividually 

Contains nut, lock washer, and spacer. Fits all Ford alternators.

If after installing a new stereo system you experience unwanted motor whine or engine noise, check all grounds on radio, amp, etc. If you still have the noise, this filter may help.Instructions included.

Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually 

Hard plastic terminal covers for the alternator. Replaces Ford Part #c7zz-14056-A

Nice reproduction of the original alternator wiring harness, 3 pin dog bone style connector and wire colors match up to the original Ford drawings. Application is 1969 Mercury Cougar standard models or 1969 Ford Mustang with factory tachometer option, all with 351/390/428CJ engines. Ford service number C9WY-14305-G. *Caution, not for use with Cougar XR7 or Eliminator models or Mustang with ammeter gauge.

Nice reproduction of the original alternator wiring harness, 2 pin dog bone style connector and wire colors match up to the original Ford drawings. Application is 1969 Mercury Cougar XR7 and Eliminator models with factory tachometer, or 1969 Ford Mustang without factory tachometer option, all with Boss 302/351/390/428CJ engines. Ford service number C9ZZ-14305-S. *Caution, not for use with Cougar standard models or Mustang with alternator warning light

This plate is what is located on the backside of your door jam where your striker threads in one. Two threaded holes for attaching the striker plates on any 1967-70 Mercury Cougar or Ford Mustang. Right and left are the same. 

Spring that holds the headlight trim ring on each headlamp to the grille. 4 springs per car, sold individually.Ford number C6AZ-13031-C.