1969 Mercury Cougar

Good used frame used to stretch your head liner over on the interior side of your sliding sun roof panel. The picture above is the support strip that runs through the middle At its widest points this frame measures 35 1/4" x 20 15/16" ...

Used original heat riser / S tube for 1968, 1969, and 1970 Cougar and Mustang 428 Cobra Jet / Super Cobra Jet. These will seldom be available. The one pictured above is the best example we've ever seen - removed from the car in 1969 just days after purchase. The pictures below are a more realistic example of the used condition you might expect. There are also additional comparison shots next to the reproduction S tube we also sell. The differences are small but the most obvious is the fact...

These steel tubes are made to exacting O.E.M. standards and specifications. All choke tubes have the proper fiberglass insulation, fittings, rubber hose, and S-clip. Also includes cold air tube when applicable.

These steel tubes made to exact O.E.M. standards and specifications.

Used grade "A" heat shield for the Mercury Cougar or Ford Mustang equipped with either the H code 2V or M code 4V 351 Windsor engine. This metal shroud and tube assembly attaches to the factory air cleaner assembly and really finishes off the engine bay. Ford part # C9OZ-9A603-A.*NOTE* For 1970, this shield was used after the build date of 2/2/1970, but it can also be used on prior dates. We suspect that the early 2 piece shroud was discontinued because of rattling noises or some...

This two piece heat shield has a very narrow application in that it is a one year only item and only for the 390 IP (Improved Performance). It does not mate to metal a "S" shaped heat riser tube but rather a flexible paper-foil tube that attaches to a reducer on the bottom side of the snorkel. Very hard to find item, harder yet to find one that has not rusted out. The unit shown is "tender" in a couple of spots. The lower section carries a Ford part number of C9OZ-9A603-D and the upper section...

C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.

Reproduction Boss 302 Exhaust Manifold Heat Shield for the 1969 Mercury Cougar or Ford Mustang

Ford part number C9ZZ-9A603-C for the upper section and C9ZZ-9A603-D for the lower for this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this lower section also. metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this upper section also.

These are getting so hard to find without a broken drain cock or rust in the metal lips. The unit pictured here is typical of what you can expect when you buy out used complete box. Plan on repairing the drain cock or other minor cracks. All doors will be functional, we will not promise the evaporator is good and we do promise the heater core will be bad. We have a few single halves if you need the half without the drain cock. Two versions for 1969-70 Mercury Cougar and Ford Mustang....

These are getting so hard to find without a broken drain cock or rust in the metal lips. We have a few single halves if you need the half without the drain cock. Soon we will have every single internal and external part from this assembly listed here, in the mean time give us a ring for those obscure parts! Two versions for 1969-70 Mercury Cougar and Ford Mustang. Difference is the evaporator and the orientation of the tubes. Look for the triangle shaped rubber line seal for the later 1969-70...

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Due to the age, there may be a minor stress crack or blemish, it will be a good used assembly. Note that this does not come with a fan assembly, so you will need to reuse your old one.Heater core IS NOT INCLUDED. This icon means that we're looking to buy this part!WCCC is a...

C9ZZ-18A651-B Complete heater and power ventilation system control assembly includes bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. The power ventilation system was a pretty rare option for 1969-70. It included a center dash register as found on air conditioned cars and directed cool air through the center of the dash. Dearborn cars would have a code "VS" on their body buck tags, and Metuchen...

Nice used pocket brochure from November 1968, featuring various 1968-69 Ford, Mercury, and Lincoln cars such as 1969 Mercury Cougar, Thunderbird, Shelby Gt 350 and XR7-G. Picture shows Ford full size XL, 1969 Mustang Coupe, 1969 Mercury Cougar, Thunderbird 4 door, Lincoln Continental.This particular edition came from the "Greater Miami" area.

NOS or new old stock - C7SZ-13A165-A Bolt like pin that one or both sides of the hidden headlight hinge rides on. 1967-68 Mercury Cougar uses 4, 1969-70 Mercury Cougar uses 2 on the outsides. Also used on many other 1967-71 Ford, Mercury, and Lincoln cars with the vacuum operated hidden headlights. 1967 - 1970 Mercury Cougar and XR7 1967 - 1969 Ford Thunderbird or T-Bird 1968 - 1969 Ford and Mercury full sized cars 1971 Ford and Mercury full sized cars 1970 and newer Lincoln Continental...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Grade "A" hoods have no rust under the lip, nothing more than a light skim coat of filler found anywhere, no damage in the hinge...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

Reproduction Eliminator hood scoop for the Mercury or Ford. Correct stud configuration, size and weight and far superior to our old scoop we offered. This scoop was made by using an original Eliminator scoop to make the mold. BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. This unit will sometimes crack at the opening. The dimensions are just like the original and measure 21 5/8" at the widest point on the front, 25"...

BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. The Scoop measures 21 5/8" at the widest point on the front, 25" at the widest point at the rear and 26 1/8" tall when stood on end and measured at its longest point. The scoop is 2 7/8" tall at the front middle when mounted on the hood.Ford part # C9WY-16C630-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73...

This original Ford service replacement hood scoop is the same as a factory installed scoop except that it does not have the embossements for the hood grille used on the very first Ram Air Cougars (prior to September 1968) and it has extra mounting stud receptacles for use on multiple applications such as the Comet GT and the Mercury Cyclone. This version does have the reinforcing or webbing like the originals. Ford part # C9WB-16C664-C, C9GB-16C664-C, and D14B-16C664-AA. Found on the bottom. ...

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

This item has been discontinued until further notice.The High tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13832 or C9ZF-13801-B.

Tested and working used Hi tone horn. The Hi tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13801-B Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

This item has been discontinued until further notice.The Low tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13833 or C9ZF-13802-C.

Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13802-C Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Reproduction gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C.

C9OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1969-70 351 Windsor 2V and 1969 351Windsor 4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. This hose is a bit longer than the 289/302 version due to the taller deck height of the 351 Windsor engines. *Note - These molded and contoured hoses were designed to work with the...

C7TZ-6A664-A Used after 02-21-1969. Original used hose that connects the original PCV valve to the carburetor spacer plate. All later 1969 S code 390-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *NOTE* These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally anything other than period original intake...

Used vacuum hose with inline muffler, connects the Servo Valve to the Regulator on 1969 Mercury Cougar and Ford Mustang with factory Speed Control. Hose about 42.7509 inches long. Ford number for hoses is C9ZZ-9D860-A.

Good used original power steering lower hose bracket and retainer with a new reproduction insulator installed in place of the original crusty or missing insulator.This bracket is for cars with the big block routed power steering hoses.

Used connector plug that attaches to the A/C vacuum switch assembly on the 69 - 72 Cougar or Mustang. The six vacuum hoses are molded into the plug, and for those instances when someone has cut a hose, simply use a hose connector.

This is the correct control valve end hoses that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. Includes both Pressure and Return hose that connect to the control valve. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against...

We are one of the only Mustang / Cougar vendors that carry "correct" power steering hoses for your early, big block Cougar or Mustang. The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find all of these hoses at your local auto parts store or the the "Mustang Discount" folks. Fits the FE Big Block 390, 427 & 428 Mercury Cougar or Ford Mustang with or without Power Steering Cooler.  Be sure to select the option to...

This is the 1967- 1968 retrofit or re-route hose kit! The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS for 1969. You will not find these at your local auto parts store or the the "Mustang Discount" folks. These hoses will also work on a 1967 or 1968 5/16" control valve fitting if it is routed the same as the big block. You will need to purchase the power steering hose bracket for the big block in order to make it work. This is a...

[No Description Provided]

Used A grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone1970 Mercury Cougar Eliminator / Cyclone1971 Mercury Cougar / Cyclone1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang...

Used spinner hubcap / wheel cover for the Mercury Cougar. This was and optional inset spinner that bolted onto your existing hubcap. 1968 was the first year the dealer option was available. Ford part # C7MA-1130-F

Brand new cap, sometimes the boxes are missing due to age.Ford part # C9WY-1130-C.Fits:1969 Mercury Cougar Standard1970 Mercury Cougar Standard

Used grade "A" XR7 hubcap / full wheel cover for the XR7 Mercury Cougar. The 1969 version of this hubcap / wheel cover used a white stripe around the center where the 1970 used black. Our grade "A" cap will have a minimal amount of scratches. Ford part # C9WY-1130-A.

New Old Stock XR7 hubcap / wheel cover for the Mercury Cougar. There were two versions of this cap, one with a white painted ring around the center, and one with black around the center. The white version was used in 1969, with the black version being used in 1970. Ford part # D0WA-1130-A

The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...

Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a pink...

Quality reproduction. Fits all 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Lin, Hey, just wanted to thank you for your prompt service. Last Friday 4/24/09 I ordered a 71 - 73 Idler Arm and today (Monday 4/27/2009) I received it. WOW!!! I just wanted to let you know that you guys are...

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory power steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a yellow paint mark on...