1969 Mercury Cougar

New Old Stock gas door. Fits all 1969-70 Mercury Cougars. Ford part number C9WY-65405A26-A

Used gas door with hinge spring. The black painted door as shown in the picture is a service replacement fuel door. Used doors are bare steel and will come with the hinge and spring.  Ford part number C9WY-65405A26-A

This filter ONLY fits the following 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19.

This filter ONLY fits the following Ford Holley 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. This is a service replacement filter, it has D2AE-9155-AA stamped on the body of the filter. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19 and C9AZ-9155-B,  FG-39.

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar

This is the OE steel tube that goes from the Ford Holley carburetor to the Carter X fuel pump. This was copied to fit the vintage Ford Holley 4150 carburetors as originally found on 1968 390-4V, and 1968-70 428CJ engines. *Note - Designed to fit OEM Carter X fuel pump with screws holding two halves together. Modern Carter fuel pumps are crimped and will need some bending of this tube to fit. Please see item 11761 tube for use with generic Carter fuel pumps. **Note - Excludes 1969 390-4V with...

This is the steel tube that goes from the carburetor to the fuel pump. Designed to fit OEM Carter X fuel pump with screws holding two halves together. Modern Carter fuel pumps are crimped and will need some bending of this tube to fit. Please see item 11761 tube for use with generic Carter fuel pumps.

This is the steel tube that goes from the carburetor to the fuel pump on the 289 or 302 with the AutoLite 4300 4 barrel carberator. Original steel version.

This is the steel tube that goes from the carburetor to the fuel pump if you have a 289 or 302, and you have the Autolite 4300 4 Barrel Carburetor. Stainless Steel.

This is the steel tube that goes from the carburetor to the fuel pump. Available in original steel or stainless steel.

Reproduction STAINLESS STEEL Fuel Pump to Carburetor Fuel Line for the 351W And the 4 BBL for the 1968 -1970 Mercury Cougar

This is the original equipment steel tube that goes from the carburetor to the fuel pump.

Reproduction fuel line for the Boss 302 engine standard steel construction. Application would be Mercury Cougar Eliminator and Ford Mustang with engine code G or the 302 HO engines. Bent for use with factory intake manifolds, OEM Carter fuel pump, and OEM installed Holley carburetor. Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

Reproduction fuel line for the Boss 302 engine stainless steel construction. Application would be Mercury Cougar Eliminator and Ford Mustang with engine code G or the 302 HO engines. Bent for use with factory intake manifolds, OEM Carter fuel pump, and OEM installed Holley carburetor. Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

Reproduction fuel line for the Boss 429 engine standard steel construction. Application would be for all Ford and Mercury products with Z code Boss 429 engines. Bent for use with factory intake manifolds, OEM Carter fuel pump, and OEM installed Holley carburetor. Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

This is the steel tube that goes from the carburetor to the fuel pump. Designed for vehicles LO-VOL fuel pump, fits 67 - 70 Mustang, 67 Cougar 390, 67 Fairlane and Torino.

Reproduction OE steel two piece fuel tank to pump fuel lines with 3/8" fittings that runs down the rocker panel on the Mercury Cougar. *NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

Reproduction stainless steel two piece fuel tank to pump fuel line with 3/8" fittings that runs down the rocker panel on the Mercury Cougar. *NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

Reproduction stainless steel fuel tank to pump two piece fuel line with 5/16" fittings for the Mercury Cougar.  *NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

Reproduction fuel pump for all 1967-70 Mercury Cougars and Ford Mustangs equipped with the 289, 302 or 351W engines. Be aware that this pump has a 3/8 inch fitting for the fuel line.

Reproduction fuel pump for all 1967-69 Mercury Cougars and Ford Mustangs equipped with either the 390-2V or 4V engines. Updated design from the originals, fuel lines fit the same.

Reproduction fuel pump for all 1967-69 Mercury Cougars and Ford Mustangs equipped with either the 427 or 428 engine. Updated design from the originals, fuel lines fit the same.

Reproduction gasket for the vintage two piece Carter fuel pump bowl for the Mercury Cougar or Ford Mustang equipped with either the 390-4V, 427-4V or 428CJ engine.

For use with your original Carter fuel pump on Cougars equipped with a BOSS 302, GT 390, 428 Cobra Jet or 429 Cobra Jet.

Exclusive to WCCC, here's our reproduction in-tank, fuel sending unit with the low fuel option. Good for all 1969 Mercury Cougar XR7's and all Ford Mustangs with 16 gallon fuel tanks. This is a reproduction of a 1969 fuel sending unit with 3 prongs (2 electrical and 1 alignment prong). The original Ford casting number was C9WF-9275-C. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. These are completely interchangeable on all 1969 20 gallon fuel tanks. *Note -...

This is the single prong version fuel sending unit for 69 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original.Check out the video below on our new gauge tester: ...

This is the stainless steel, single prong version fuel sending unit for 69 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original. Check...

This is the stainless steel, single prong version fuel sending unit with 1/4"  return line for 69 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to...

New manufactured fuel / gas tank for 1969 Mercury Cougar and 1969 Ford Mustang, 20 gallon capacity, has drain plug. This is the economy version, which has a slightly different stamping, and is made in Taiwan.Replaces Ford part #C9ZZ-9002. *NOTE* Tank will fit into all 1967-68 cars, fuel filler necks must be adjusted to fit with this taller tank. Sending units ideally should be changed to the 1969 sending units. 1970 cars with California emissions will have to change filler necks entirely. ...

Original style wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Replaces Ford Part #: C5ZZ-8287-A.

Used original wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Ford Part #: C5ZZ-8287-A.

Reproduction fuel / gas tank for the Mercury Cougar or Ford Mustang. 20 Gallon capacity, very correct reproduction. Unit is designed to OE fit, form and function requirements accomplished by leveraging our OE fuel system design expertiseMade with corrosion resistant Ni Terne steel for durabilityUnit is leak tested after production to ensure product in free from fuel and / or evaporative leaksEach new fuel tank is road tested to ensure real world performance and to verify that each design...

New manufactured stainless steel fuel / gas tank for 1969 Mercury Cougar and 1969 Ford Mustang, 20 gallon capacity, has drain plug. Replaces Ford part #C9ZZ-9002. *NOTE* Tank will fit into all 1967-68 cars, fuel filler necks must be adjusted to fit with this taller tank. Sending units ideally should be changed to the 1969 sending units. 1970 cars with California emissions will have to change filler necks entirely.

If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970. Replaces Ford part # C9AZ-9H576-A.

This is our reproduction, uncut, driver side (left hand), long, front and rear floor pan for your Mercury Cougar convertible.

This is our reproduction, uncut, passenger side (right hand), long, front and rear floor pan for your Mercury Cougar convertible.

This is a reproduction long front and rear floor pan. Will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but this will work for all years.

Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...

This is a reproduction long front and rear floor pan. Will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but this will work for all years.

Reproduction full length passenger side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years.

C8OZ-14A187-A Unique 1/4"-20 bolt for attaching the fuse blocks. 69 70 71 72 73 Mercury Cougar Ford Mustang fuse panel attaching bolt. Includes "C" clip and spring as shown. "C" clip keeps the bolt in the black fuse block.

C8OZ-14A068-A Black Bake-O-Lite original fuse block. Grade A, no cracks or chips. Perfect for upgrading your broken fuse block that has a nice wiring harness. 69 70 Mercury Cougar Ford Mustang fuse panel. Sometime in the later part of 1972 Ford switched to a nearly identical brown fuse block.

C8OZ-14A068-GRADEB Black Bake-O-Lite original fuse block. Grade B, not broken, but will have chips from prying out fuses. Perfect for upgrading your broken fuse block that has a nice wiring harness. 69 70 71 72 Mercury Cougar Ford Mustang fuse panel. Sometime in the later part of 1972 Ford switched to a nearly identical brown fuse block.

Reproduction Accessory wire with Buss bar for the accessory terminal found optionally on 1969-73 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded style triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire length is just over 9 inches in length.

This fusible link is a section of wire connecting the starter solenoid on one end and wiring harness that passes through the firewall to mate with the top switch wiring. Correct for power sunroof equipped Cougars. May also work for XR7 and Standard convertibles.

Individual reproduction anti-rattle rubber gasket for the stainless steel accent ring used on the Mercury Cougar or Cyclone. This unit is used to keep the accent rings from rattling and driving Cougar and Cyclone owners insane. You can run your wheels without these rings, however Ford used them, so we sell'em. Sold individually.