1967 Mercury Cougar

Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

Reproduction torque box gusset for your 67 - 70 Cougar or Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box for extra strength. Sold as a pair.

Driver side (left hand) outer section of the torque box for the Mercury Cougar and Ford Mustang for both coupe and convertible.

Rebuilt C4 24 spline torque converter for the 1967 - 68 Mercury Cougar or 1966 - 69 Ford Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core. Ford part number C6AZ-7902-M. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of...

Rebuilt C6 FE Engine torque converter for the 1967 - 70 Mercury Cougar and 1966-70 Ford and Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core. 1966-70 Ford FE engines include: 352, 360, 390, 427, 428, etc. Ford part number C8OZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad...

These long rods are installed horizontally in your trunk and attach to the trunk lid hinges. We only remove these bars in pairs from cars that demonstrate that they can in fact support the weight of the deck lid on their own. We do not save rusty, bent or weak springs. These are the best we have to offer from our Western parts cars. 1967-70 torsion springs C7WY-6544890-A and C7WY-44891-A. Limited to supply on hand. The body section of the shop manuals describe how to adjust these bars, we...

New large black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 21" X 9" X 9" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!

New small black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 17" X 8" X 8" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!

NOS Autolite 4300 training handbook. Filled with details pertaining to operation, adjustments, overhaul and servicing of the Autolite 4300 carburetor which was used starting in 1967.  Volume 67 S2 L2, 9503.1, 9503.2

Reproduction transition panel for the 67 - 70 Cougar. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below:

This kit is an easy way to covert your 289 / 302 / 351W engine from a C4 or C6 transmission to an Automatic Overdrive Transmission.Kit includes: Cross memberTrans Mount InsulatorSlip YokeKick Down CableFlex Plate AOD Shift LinkageThis is just the kit, and does not include the full transmission! NOTE: This item is shipped from our supplier direct to you, so expect 1-2 weeks for shipping. ...

Core C4 transmission for a 1967 Mercury Cougar or Ford Mustang. Tag number PEE-C. Floor shift C4 Transmission.Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1967 Mercury Cougar. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core C6 transmission for a 1967 Mercury Cougar or Ford Mustang. Tag number PGA-P or PGA-P1. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1967 Mercury Cougar with 390 engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Used C-4 transmission 90 degree brass fitting for the rear oil cooler line. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.Not all of the transmissions had a 90° fitting. Compare with your cooling lines.

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with a V-8 engine and the C-6 automatic transmission. These lines are sold in pairs.

Fits all applications for both automatic and manual transmissions, big block and small block. Will also work with your Tremac / T-5. Replaces Ford part # C4DZ-6068-A.

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

An exact copy with a beautiful chrome mirror finish.

An exact copy with a beautiful chrome mirror finish. 1 inch deeper than stock.

An Exact copy. Natural gray paint for correct look and rust prevention. 1 inch deeper than stock.

Flawless chrome plating, available in stock depth only. Includes drain plug.

An Exact copy. Natural gray paint for correct look and rust prevention.

Flawless chrome plating, available in stock depth only. Includes drain plug.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

New manufactured transmission yoke for a T-5 5 speed transmission.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

Used transmission tunnel specialty cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the area you're working on and send us a few digital pictures so we can cut to your needs. Pricing may not change, because we're...

This two piece painted trim / moulding set helps to secure the package tray in place at the bottom of the rear window. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Replaces Ford part #: C7ZZ-3656-A, concours correct for all 1967 Mustang's and Cougar's. This beveled ornamental plastic ring is for your 1967 steering wheel hub. The inner diameter is 3 3/4" and the outer diameter is 4 3/8" and it stands 5/16" tall. This ring fits many FoMoCo products but keep in mind there is another version that is completely flat like a washer. We suggest you use soapy water and heat your hub before trying to slip this on. It also helps if you go around the perimeter and...

Reproduction driver side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Driver side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1967-68 Mercury Cougar. These special cuts are removed from rust free examples from a used Cougar. Ford part number C7WY-6545119-A.

Reproduction passenger side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Passenger side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1967-68 Mercury Cougar. These special cuts are removed from rust free examples from a used Cougar. Ford part number C7WY-6545118-A.

Reproduction driver (left hand) side trunk floor panel with trunk drop off. This is a complete replacement for the factory spot-welded-in panel, not a partial cut.For more info on this new trunk panel, check out this video below:

Reproduction passenger (right hand) side trunk floor panel with trunk drop off. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below:

Comes with trunk drop offs and complete tail panel. We would be happy to modify the way in which we remove this part to best fit your needs. Figure about $250 for shipping and crating via www.forwardair.com. Please call to order this one.

These reproduction J clips mount to the underside of the deck lid and fit Standard and XR7 trunk lids.

Used cover with dull chrome. This used to be a very sought after and expensive part due to how difficult they were to find. Now that our show quality reproductions are here they have little value... Great for someone that just wants their driver to look complete. Fits all 1967-68 Mercury Cougars, Standard and XR7 models. Decal inserts available separately. ...

For 1967 both the XR7 and Standard model used the decal shown on this reproduction trunk lock cover. For 1968 only the Standard model used this decal as the XR7 and XR7G had their own unique center badging. *NOTE* You will have to apply the licensed by Ford decal to the deck lock cover. Click on images to enlarge. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This is for the person who already has a decal or XR7G emblem to place in the center section. Maybe you have a custom idea? Same great quality and flawless fit as our other deck lock covers.*NOTE* After a long hiatus these are finally back in stock! They were worth the wait, the quality is really good on this new reproduction.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This reproduction is pathetic... It's made from the same material as a cheap picnic table cloth (you know, the red checkered ones?) The only way you will ever get this plastic "table cloth type" mat to lay flat is to glue it down. They do however work well for catching oil spills under your Cougar when turned felt side up. No returns on this product, we suggest no mat is a better alternative than this poor quality reproduction. It's that bad... Please look at our premium quality trunk...

This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern by Auto Custom Carpets. Do NOT confuse this with the light duty mat you will see elsewhere listed for the same money or less. The budget mats you see elsewhere weigh only a few ounces and flail around inside your trunk every time you close the lid! The pattern will not smudge or wear off easily and it will lay flat and fit...

Complete reproduction trunk floor pan for the 67 - 68 Cougar. Also includes rear shock support, axle bumper mount, and rubber plugs for the shock holes. When ordering this item, keep in mind that it is an over-sized box which will be drop shipped from our supplier in California or available for in store pick up at WCCC. You can expect to pay up to a few hundred dollars for shipping (oversized items must be truck freighted). Often, all you need is the left or right trunk sections. You can save...

Complete non assembled trunk pan kit. Included are the transition panel, trunk floors, rear taillight support and shock support. This kit will require you to assemble and weld in all individual pieces of the rear trunk pan on your own.  This is an oversized box, so expect to pay about $300 for shipping, depending on location.