1967 Mercury Cougar

This used brake pedal support bracket or brake pedal hanger is for the Mercury Cougar or Ford Mustang equipped with power disc or drum brakes. We have carefully shown the mounting position of the pedal so you can drill your existing manual brake pedal hanger when converting from manual to power brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means...

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design. Two different sized brackets used, this is the larger one that is 1-3/4 inches wide. The bracket that goes in the corner above the switch panel is 3/32" less. It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend...

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the smaller design. Two different sized brackets used, this is the smaller one that is 1-21/32 inches wide. This bracket goes in the corner above the switch panel. The larger bracket is 1-3/4" or 3/32" wider. It was obvious what the original intent was on this design in that a tab on the L...

Reproduction set of 5 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design of the two and by far the superior. Replaces item # 31908Through 67-68, there were four different style brackets, you can see all four by following this link. ...

This often times missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design.Through 67-68, there were four different style brackets, you can see all four by following this link. ...

Reproduction set of 5 XR7 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. Our improved design is better than the original in that the tab extends into the rectangular recess in the dash bezel which anchors in MUCH more securely. Replaces item # 31907Through 67-68, there were four different style brackets, you can see all four...

Radio support bracket for 1967-68 Mercury Cougar and Ford Mustangs without consoles. Used on AM, AM/FM, and AM/8Track factory radios.Replaces parts #s C7ZA-18888-A & C8ZA-18888-A, as found in the electrical assembly manuals.

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

This is the right hand or passenger side spring that holds the rear license plate or fuel door in the upright position. Fits 1967-68 and 1971-73 Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-A

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.  

C7ZZ-5482-C This is a factory used sway bar for the Special Handling Package as found on with the 1967 and 1968 GT option. This bar was factory identified with a single 'Green' paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.

Used front sway bar, does not include any mounting brackets or end link kits. Ford part # C7WY-5482-A.

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Plunger switch that mounts to the air distribution manifold behind the center A/C vent. A mechanical lever operates the switch when the air damper is in the proper location to distribute air through the center air conditioning vent of the dash. This switch controls the clutch on the A/C compressor. 1967-68 Mercury Cougar and 1966-67 B Body Ford, Fairlane, Ranchero, and C Body Mercury Comet and other variations Cyclone etc. Tested and working switch. On Cougar and Mustang it attaches to the...

This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.

Used air conditioning thermostat switch for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Ranco for Ford. Ford part numbers C7ZA-19618-C or C7ZZ-19618-A.

C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573.*Note - 3 speed switches are different than the 4 speed switches.

Reproduction backup lamp switch that mounts to the factory 4 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-561. Replaces Ford part number C7ZZ-15520-A.*Note - 4 speed switches are different than the 3 speed switches.

Reproduction brake light switch for the Mercury Cougar and Ford Mustang equipped with power disc brakes. This is a high quality replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford Part #: C9VY-13480-A.

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...

NOS one year only column mounted switch for activating the tilt column. Ford part number C7ZZ-13713-A

Used one year only column mounted switch for activating the tilt column.Ford part number C7ZZ-13713-A

New Old Stock switch for the 1967 Mercury Cougars and Ford Mustangs that came with the 3/4" door jamb switch. This switch will be yellowed from age. Additionally, this switch for the 3/4 inch mounting hole was used on 1965-66 Full sized Ford such as Custom, 500, Galaxie, and XL models, full sized Mercury such as Monterey, S-55, Montclair, and Park Lane. 1965-67 Fairlane, 500, XL, Ranchero, and GT. 1965-67 Mercury Comet, 202, Capri, Caliente, and Cyclone. 1965-67 Ford Mustang, 1965-67 Ford...

Nice reproduction of the 1967 Door Jamb Switch. Replaces Ford Part #: C5AZ-17317-A Please note that most of the plastic bodied, reproduction door jamb switch currently available are for the later model cars and have smaller female plug holes that will not work on a 67.

This is a good used switch for the 1967 Mercury Cougars and Ford Mustangs that came with the 3/4" door jamb switch. This switch will be yellowed from age. Additionally, this switch for the 3/4 inch mounting hole was used on 1965-66 Full sized Ford such as Custom, 500, Galaxie, and XL models, full sized Mercury such as Monterey, S-55, Montclair, and Park Lane. 1965-67 Fairlane, 500, XL, Ranchero, and GT. 1965-67 Mercury Comet, 202, Capri, Caliente, and Cyclone. 1965-67 Ford Mustang, 1965-67...

C7ZZ-14018-F Left side door ajar switch found on all 1967 Mercury Cougar XR7's and part of the Safety Convenience Package found optionally on Mercury Cougar or Ford Mustang. The safety convenience package or "convenience control" option included 4 warning lights either mounted on the dash (without air conditioning) or on the console. Switch assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 69, C7ZB-10B997-A switch assembly left hand. The engineering number...

C7ZZ-14018-E Right side door ajar switch found on all 1967 Mercury Cougar XR7's and part of the Safety Convenience Package found optionally on Mercury Cougar or Ford Mustang. The safety convenience package or "convenience control" option included 4 warning lights either mounted on the dash (without air conditioning) or on the console. Switch assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 69, C7ZB-14018-A switch assembly right hand side. The engineering...

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang, and most 1965-69 Ford and Mercury full sized cars such as Galaxie, Monterey, Parklane, Montclair, etc.Fits 67 CougarFits 68 CougarFits 65 Mustang Fits 66 MustangFits 67 MustangFits 68 Mustang

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

Unlike the 1968 Cougar headlight switch, the 1967 and 1971-73 version does not have the three vacuum ports connected to it. Don't be fooled . . . Most vendors will sell you a Mustang switch and tell you it is the same. Visually it may look the same but internally it has a circuit breaker designed for a two headlight system, the Cougar has four headlights. If you only use the low beams you would be fine but if you have all four lights on you will soon experience a blackout. If your original...

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

Mounts to the rear of the factory installed heater control ventilation control panel on 1967 Mercury Cougar and Ford Mustang. Switch and wiring pigtail with plug.Replaces part # C7ZZ-18578-A.

Mounts to the rear of the factory installed heater control ventilation control panel on 1967 Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1967 selector button kit. Click this LINK for shinny new button awesomeness!Ford part # C7ZZ-18578-A.

New Old Stock NOS Fan switch for use with air conditioning on any 1967 Mercury Cougar or Ford Mustang. Mounts to the rear of the factory installed air conditioning ventilation control panel on Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1967 selector button kit.Ford part # C7ZZ-19986-A. ...

Mounts to the rear of the factory installed air conditioning ventilation control panel on Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1967 selector button kit.Ford part # C7ZZ-19986-A.

Sold individually, three of these are mounted to your 1967 steering wheel. Comes with two screws as shown. Also sold in a set of 3. Check out the very first Cougar in our video below! ...

Sold in a set of 3, these are mounted to your 1967 steering wheel. Comes with two screws as shown. Also sold individually. Check out the very first Cougar in our video below! ...

New Old Stock neutral safety switch for the C-4 transmission installed in early 1967 Mercury Cougar and 1966-67 Ford Mustangs. Found on cars before build date 12/15/1966. This neutral safety switch is identified by having two plugs that plug into the single 4 pin plug, coming from the firewall. The later neutral safety switch with a single 4 pin plug will also work fine.Look for a transmission code of W on your door data plate. If your car has a code U, your original transmission was an C-6...

New Old Stock neutral safety switch for the C-4 transmission installed in early 1967 Mercury Cougar and 1965-67 Ford Mustangs. Found on cars before build date 12/15/1966. This neutral safety switch is identified by having two plugs that plug into the single 4 pin plug, coming from the firewall. The later neutral safety switch with a single 4 pin plug will also work fine.Look for a transmission code of W on your door data plate. If your car has a code U, your original transmission was an...

Tested and inspected neutral safety switch for the C-4 transmission installed in early 1967 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/15/1966. This neutral safety switch is identified by having two plugs that plug into the single 4 pin plug, coming from the firewall. The later neutral safety switch with a single 4 pin plug will also work fine.Look for a transmission code of W on your door data plate. If your car has a code U, your original transmission was an C-6 and...

This reproduction neutral safety switch is for the early 67 Cougars with a C-4 automatic transmission. It has two small plugs as opposed to one large like the later version we also have listed. Ford part #  C4AZ-7A247-C, SW 368.

Tested and inspected neutral safety switch for the C-4 and C-6 transmissions installed in 1967-69 Mercury Cougar and 1967-69 Ford Mustangs. Look for a transmission code of W or U on your door data plate. If your car has a code X, your original transmission was an FMX and uses a different neutral safety switch.Replaces Ford Part #: C7DP-7A247-A, C8ZP-7A247, C9ZZ-7A247-C, SW 887.Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969...