Your cart is empty!
If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
#8 tapping screw for attaching the map pocket to the door panels on any 1967-68 Mercury Cougar XR7. Sold individually, set of 4 needed per car, 2 per side. Chromed, Phillips pan head screw. AMK B-13283.
part # C2OZ-6065-A. Shorter of the two head bolts.
part # C2OZ-6065-B. Longer of the two head bolts.
Hex screw for attaching the black plastic elbow to the right or left hand A/C dash duct. Correct replacement #8 washer head tapping screw. Sold individually, two needed per car. One on each side. Fits 1967-68 Mercury Cougar and Ford Mustang with factory air conditioning.
Reproduction A/C Tag Retainer for the 1967 - 1973 Mercury Cougar
part # 370608-S. Used in multiple places on mounting brackets.
This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually. These clips attach to posts built in to the car. In case you're missing some...
Ford Part # 379390-s
Fits 1967 Standard or XR7
This screw / stud seems to always be missing. This screw is just a little longer than stock to accommodate installing the Hi-Po air cleaner. Fits most Autolite carburetors. Size: 4 1/8 inches length 1/4-20 X 5/16-18 threads. Check your thread size on the carburetor, we think that starting in 1969 the Autolite 4300 carburetors had 1/4-20 threads. Please note that this stud has 5/16-18 threads going into the carburetor. Replaces Ford Part #: 370971-A *Note - Check your carburetor, it will...
Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)
Reproduction Alternator Connection Nut for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold insividually
Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Reproduction apron nuts for the 67 - 70 Cougar or Mustang. These are the fasteners that are imbedded into the aprons on either side of the engine compartment and are used to fasten the hood hinges to the car. Sold in a pack of 6 fasteners.
Four per car unless you have a 1968 decor or standard model that has the unique three hole armrest and then you will need six. Replaces Ford part # C7AZ-6224146. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...
Fits 1967 and 1968 Standard or XR7
Replaces Ford Part # 50828-S
Zinc Dichromate (yellow-rainbow)
OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S
Sold individually. Stainless Steel
Barrel nut for the 3/16" stud found on the 6.5 Liter badge and the GT badges that mount on the fender of 1967 Mercury Cougar and Mercury Cyclone GT with the S code 390 engine. Same GT badge on the 1968 Mustang GT models. Item sold individually.
These barrel nuts or clips are exactly like the original ones inserted into the trunk for attaching 1967-68 "Mercury" script, and 1971-72 Mercury Cougar "Mercury" Hood scripts. The manufacturer indicates that these tubular nuts fit 1/8" holes. Pin size on those emblems are 3/32".These clips are also used to attach the 1967 quarter panel emblems.
Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"
Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.
Reproduction 289 - 302 Alternator Bolt w- Smog for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold individually
Coil bracket mounting bolt for all V-8 engines as found in 1967-73 Mercury Cougar and Ford Mustang. This3/8-16 bolt attaches the coil bracket to various places on the engines. Either on the intake manifold or the cylinder head. Will fit stock Ford cast iron intakes as found 1967-73. AMK bolt B-13722.
Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
New screw with a correct 3/8 inch hex head for installing all armrests for all years.
part # 382101-S2
part# 372434-SSold Individually.Head size: 5/8"Thread size: 7/16"
Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.
part # C1AE-6065-C. Shorter of two.
part # C1AE-6065-A. Longer of two.
Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).
Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351.
Concours bolt for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. Sold individually, or in a set of 4. 1/2 inch hex head size an the threads are 5/16-24. This bolt is approximately 7/8" to the shoulder and 1-1/8" in total length. Replaces Ford part # 380288-S. ...
Not a concours correct head pattern, but it looks good. Bright cadmium finish. 5/16-18 x 7/8 long.
Replaces Ford part # 385664-S
Replaces Ford part # 378172-S
Replaces Ford part #375381-S Phosphate & Oil Finish
part # 379068-SSold individually
Used front crossmember bolt for the Mercury Cougar or Ford Mustang. It is crucial that you use this correct tapered bolt when installing the front cross member.
Reproduction zinc front shock bolt with correct anchor symbol on the head, just like the originals.Sold individually.
Front U clamp sway bar bracket bolt, for any 1967-68 Mercury Cougar or Ford Mustang. 3/8-16 x 1.0 Grade 5 bolt. Sold individually, 4 per car. part #20408-S
Reproduction intake manifold bolt for the Mercury Cougar or Ford Mustang equipped with either the 390 or 428 engine. These little units are sold individually.
Plain head, fine thread. Not concours, but meets or exceeds original specs. Sold individually.Ford part # 380328-S.