Your cart is empty!
Mounts onto the transmission. Fits all 1967 - 1968 8 Cylinder.
New internal speedometer gear fits 4 speed toploader transmissions. Replaces Ford Part #: C5ZZ-17285-A.
New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.
Reproduction A/C Tag Retainer for the 1967 - 1973 Mercury Cougar
Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
Molded rubber plug, seals access hole in the side of shift housing. Replaces Ford Part # : C5ZZ-7C147-B Check out our video on rebuilding your shifter below: ...
Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...
Fits perfect! The collar that slips into the opening of the bell housing is very tight for a precise fit that will withstand high horse power motors.
Reproduction Alternator Connection Nut for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold insividually
Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Replaces Ford Part # 50828-S
Zinc Dichromate (yellow-rainbow)
This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A
C5OP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1967 - 1968 Mercury Cougar with any 289 or 302 engine and automatic C4 transmission, code W on your door tag. 1967 - 1972 Ford Mustang with 250, 289, or 302 engine and automatic C4 transmission, code W on your door data plate. Fits the 157 tooth flex plates. There was a 164 tooth flex plate that came later. NOTE * Grade B bell housing will have a chip or heavy scarring on the bottom, see photo...
This used bezel will have no broken or missing parts but will need a new adhesive aluminum overlay. Most likely the white will be missing from the P R N D 2 1. We also have grade "B" used units with minor flaws for less than half the price. This icon means that we're looking to buy this part! WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...
Used shifter plate bezel for the Mercury Cougar or Ford Mustang equipped with a 3 or 4 speed manual transmission, but without a center console. This unit is a nice upgrade from the simple plain Mustang boot retainer. This version is the one held down with no screws, the rubber boot holds it in place. Part number C7WB-7262-D is the one being sold.Ford part # three different casting numbers with very slight variations. C7WB-7262-A, C7WB-7262-C, & C7WB-7262-D. Check out our video on...
These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.
Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.
part # C1AE-6065-C. Shorter of two.
part # C1AE-6065-A. Longer of two.
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).
Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351.
Replaces Ford part # 385664-S
Replaces Ford part # 378172-S
part # 379068-SSold individually
Used front crossmember bolt for the Mercury Cougar or Ford Mustang. It is crucial that you use this correct tapered bolt when installing the front cross member.
Replaces Ford part #: 378782-S
Sold individually, pivot stud for the aluminum power steering pump mounting bracket. fits all applications for small or big block. Also used on the 1970 Mercury Cougar with 428CJ. Phosphate & Oil (gray-black)
Reproduction water pump bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These are zinc (dark silver) plated and sold individually. This bolt is approximately 2-5/8" to the shoulder and an approximate overall length 2-3/4".
NOS water pump bolt for the Mercury Cougar or Ford Mustang. This bolt is approximately 3-1/2" to the shoulder and an overall approximate length of 3-3/4".Replaces part # 376258-S.
part # C9ZE-6345-A. Used on 289 / 302 / 351w 7/16" by 3" shaft. Sold individually
Alternator bolt and installation kit for 1967 Mercury Cougar and Ford Mustang with 390 engines. Includes spacer and pivot bolt and the other three bolts and washers as shown.
New Bolt kit, for the installation of a water pump on any Ford 352, 390, or 428CJ engine. Fits all 1967-70 Mercury Cougar and Ford Mustang with 390-4V, 390-2V, and 428 Cobra Jet engines.
New valve cover bolts for all 289-2V, 289-4V, 302-2V, 302-4V, and 351W-2V, and 351W-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 12.*Note - Excludes Boss 302 and 351C engines (see part number 8317)Replaces Ford part number 373071-S.
Reproduction valve cover bolts for all 390 / 427 / 428 Ford engines.
Fastens the battery tray to the fender apron.
Reproduction bolts and washers for the C-4 automatic bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and code W automatic transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1965-68.
Reproduction bolts and washers for the C-6 automatic bell housing on any 1967-70 Cougar or Mustang equipped with a 390 / 428 engines and code U automatic transmissions. Bell housing to engine block bolts. Fits most all other Ford big block V-8's from 1966-70.
Reproduction bolts and washers for the manual transmission bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1967-68.
Reproduction bolts and washers for the manual transmission bell housing on any 67 - until 2/1968 Cougar or Mustang equipped with a 390 / 428.
Reproduction bolts and washers for the manual transmission bell housing on mid , like Feb 1968 - 1970 Cougar or Mustang or other Ford car equipped with a 390 / 428 engines. Bell housing to engine block bolts.
New set of bolts for fastening the transmission inspection cover on all 1967-70 Mercury Cougar, Ford Mustang, and Ford anything with 390, 428CJ, and 352 or any FE style Ford engine. Includes 3 and 4 speed transmissions.
Pair (2) Bolts for securing the inspection cover for any C-4 automatic transmission 1967-68 Mercury Cougar or 1965-70 Ford Mustang. Additionally also fits FMX transmissions 1969-73 Mercury Cougar.or Ford Mustang.
4 Bolts for securing the inspection cover for any C-6 automatic transmission 1967-70 Mercury Cougar or Ford Mustang.
Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury Cougar and Ford Mustangs, and likely all of other floor shift Ford products from this time period. Check out our video on rebuilding your shifter below: ...
Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...