Exhaust

Band or ring style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Comes with a course sheet metal type threaded hex head bolt. Ford part number C5DA-5A272-B. *Note all 1967 & 1968 Cougars had 2 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C6AA-5A272-A is the factory style 2-1/4" tailpipe clamp.

Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford.   Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1967 - 1973 models with 2" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Many of the stock exhaust systems were actually 2 inches. Most reproduction "Systems" are 2-1/4, use accordingly. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Reproduction dual exhaust tip to hanger clamp for the 1967 - 1970 Mercury Cougar and Ford Mustang.

Reproduction pair of exhaust pipe clamps for your 67 - 69 Cougar or Mustang.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

This 2 inch dual exhaust system is manufactured right here in the good old USA from an original 1968 J code Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

This oversized 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from original 1968 Cougars equipped with the 289 or 302 engine. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging...

This oversized 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from original 1967-68 Cougars equipped with the 390 or 427 engine. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached...

NOTICE - 3/15/16 - The rare transverse mufflers are currently being reproduced and may take up to 2-3 months from now to get to our exhaust manufacturer. You can preorder now, but expect a bit of a wait. These systems are manufactured right here in the good old USA from an original 1967 S code Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, 1 transverse resonator, and a right and left tail pipe. The system is constructed from 2 inch aluminized...

Dual Exhaust Tailpipe U Hanger Bracket for the 1967 Mercury Cougar and Ford Mustang

New Dual Transverse Muffler as used on the 67 Cougar with 390. This muffler is an exact match (connection wise) to the factory Ford OEM Transverse muffler that is no longer available. Muffler dimensions: 20" x 11" x 4 1/2" Aluminized SteelSeam Locked like the originalsSlightly increased flow over stock mufflerAuthentic dimensions to OEM mufflersStock dimensions for absolute proper clearances ...

Factory cast iron exhaust manifold set, both right C6OE-9430-E and left C6OE-9431-F side exhaust manifolds. Same manifold for all 289 and 302 engines for both 1967 and 1968. Random date codes.

C6OE-9431-F Factory original cast iron exhaust manifold for driver side. Ford manifold used on all 1967 and 1968 289/302 engines.

C60E-9430-E Factory original cast iron exhaust manifold for passenger side. Factory Ford manifold used in both 1967 and 1968 for all 289 and 302 engines. The heat riser stud will not be broken off like most. If this not a concern to you and want to save money please let us know!NOTE* Item has been sand blasted for pictures. The manifold you will get will be off of a parts car and will need cleaning.

Spot on reproductions made of higher quality steel that OEM!

Reproduction high performance cast iron exhaust manifolds for the 1967 - 1968 Cougar or Mustang equipped with the 289 or 302 engine. Designed to be exactly like the originals, with correct markings and raised part numbers. Includes studs and nuts.Replaces Ford part numbers C6OE-9430-E and C6OE-9431-F

390-4V factory cast iron exhaust manifold set, both a correct right and left set of matching exhaust manifolds. The passenger side does require a spacer, which is not included. Indicate in the comments section if you want the early 1967 passenger side with C6OE-9428 casting or late 1967 and 1968 with C7OE-9430 casting.* If concours or dates don't mean anything to you, we suggest the set with the late 1968 passenger side exhaust manifold, with doughnut chamfer, that does not require...

Correct black phosphate bolts for use with 289 HiPo (K-code) exhaust manifolds. Although Cougars never offered a HiPo 289, the HiPo manifolds will fit any 67-68 289 or 302.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds. 390 and 427-4V engines without exhaust heat risers. That kit would include a studded bolt for the heat shield. See item 41282.

This direct replacement H pipe only for any 1967-68 Mercury Cougar or Ford Mustang equipped with either the 289 or 302 engine and stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 289 or 302 engine. We also sell this H pipe in a 2 inch diameter and have OEM style dual exhaust systems...

Direct replacement H pipe only for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds that includes the spacer valve on the passenger side. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 390 or 427 engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds that includes the spacer valve on the passenger side. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 390 or 427 engine. We also sell this H pipe in a 2 inch...

Bracket and insulator that mounts to the body and the left side of the factory transverse muffler. All 289 engine applications. Ford part number C7WY-5260-A or  C7WY-5260-B. *Trivia - All 1967 Cougars with 289 engines had a single exhaust from the factory. Both the C code 289-2V and A code 289-4V.  

Bracket and insulator that mounts to the body and the right side of the factory transverse muffler. All 289 engine applications. Ford part number C7WY-5260-B.

Mounts to the frame on the left side of the fuel tank. Supports and holds the rear of the tailpipe stationary. Ford part number C7WY-5260-D.

Mounts to the frame on the right side of the fuel tank. Supports and holds the rear of the tailpipe stationary. Ford part number C7WY-5260-C.

Mounts to the rear of a 'turbo' style muffler. Left side bracket. Ford part number C7ZZ-5A246-F.

Mounts to the rear of a 'turbo' style muffler. Right side bracket. Ford part number C7ZZ-5A246-G.

The 289 used a transverse muffler with hangers on either end and dual exhaust was not an option. The 289 Cougars for 1967 also did not use a tail pipe hanger like their 390 brethren did, the tail pipes were free hanging. We have observed in the many 1967 parts cars in our yard that many Cougars have had an after market tail pipe hanger installed at some point. Many Cougars have a hanger welded or bolted to the passenger side tie down bracket.

Includes the two muffler (aka resonator) hangers and two tail pipe hangers. Only the 390 got tail pipe hangers in 1967, the 1967 289 had muffler hangers only and dual exhaust was not an option on a 1967 289 equipped Cougar, even if it were an "A" code 289 4V. Will not be overly rusty and will have decent rubber still intact. We cannot guarantee that the mounting hardware will be included as shown on the resonator brackets.

Muffler mounting tabs for using factory Ford muffler hangers on aftermarket turbo style exhaust mufflers. These help achieve that concours look using a replacement muffler or mufflers. We recommend using your existing horse shoe shaped muffler hanger as a jig for locating these tabs prior to welding. These were copied from the original style tabs found on most 1968-73 Mercury Cougar and Ford Mustangs. 1967 cars and some Mustangs used a single transverse muffler behind the rear axles, these may...

Correct for all 1967 Cougars with a 289. Keep in mind the Cougar never came factory with a 289 HiPo.

Reproduction hex screw for exhaust pipe clamps for the 1967 - 1973 Mercury Cougar and Ford Mustang. 5/16 x 1-1/2 screw. Fits original and new clamps.

Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.

Reproduction Exhaust Manifold Pipe Stud Kit for the 260, 289, 302, 351 and 1969 390GT 1967 - 1972 Mercury Cougar and Ford Mustang

Kit has the longer studs for use with spacers or butterfly spacers, between 390 and 428CJ passenger side exhaust manifolds and H pipe flange.

This rear segment exhaust system is manufactured right here in the good old USA from an original 1967 S code Cougar. It is an OEM style direct replacement system that includes: 2 intermediate pipes, 2 mufflers, 1 transverse resonator, and a right and left tail pipe. The system is constructed from 2 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so...

Used exhaust manifold spacer without butterfly valve for use on 1967 to mid 1968 Mercury Cougar, Mercury Cyclone, Ford Fairlane, and Ford Mustang with 390 or 427-4V engines. Straight factory used spacer. Most cars came equipped with a thermal spacer that often times gets frozen with time. No obstruction with this one.Note - Does not fit the slightly larger 428CJ exhaust manifolds. Ford part number C6OZ-9A427.

Used exhaust manifold spacer with butterfly valve for use on 1967 to mid 1968 Mercury Cougar, Mercury Cyclone, Ford Fairlane, and Ford Mustang with 390 or 427-4V engines. Fully functional, we test these with a heat gun, they do open and close. These thermostat control valve assembly mates to the 1967 and 1968 passenger side 390 exhaust manifold up until about Feb 15, 1968. Easy to tell if it is needed with your manifold, no chamfer for the exhaust donuts at collector? you need this or a...

OEM Style Universal Exhaust Hanger Bracket 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Band or ring style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Comes with a course sheet metal type hex head bolt. Ford part number C6AA-5A272-A. *Not all 1969 & 1970 Cougars had 2-1/4 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C5DA-5A272-B is the factory style 2" tailpipe clamp.

C7OE-9431-A Factory original cast iron exhaust manifold for driver side. 1967, 1968, and 1969 390/427 left side manifold remained unchanged for all three years. Includes 1968 X code 390-2V Premium fuel cars. Click on images to enlarge. ...

Factory original cast iron exhaust manifold for the passenger/right side and is probably a mid-year change for 1967. For both S & X code 390 engines and W code 427 GT-E engines up until 2/15/1968. Butterfly spacer not included. Ford part # C7OE-9430-C.

C6OE-9428-A 390-4V factory original cast iron exhaust manifold for passenger side. Even though the photo shows a chamfer where an exhaust donut would go, the proper 1967 manifold would have been cast flush, and a butterfly spacer would have been used. The spacer had a flapper that partially blocked the pipe and allow heat to be dissipated upwards to the choke. Spacers not included. We suggest purchasing the later version of manifold that did not use the spacer. *Note, a spacer may be needed if...