Fasteners

 2 piece fuel line. Kit is for fuel and brake lines under the car. Comes as shown. Quality AMK kit. Fits 1967 Mercury Cougar and Ford Mustang. F-3962

If your fuel line follows the brake line down the transmission tunnel then you have an early model 1967 and this is the right clip set for you!

All the nuts, bolts, shims and washers needed to mount the bumper brackets to the frame and then the bumper to the bumper brackets. This kit includes foam looking washers to cover the bumper bolt holes.  This is not technically correct.  From the factory the originals would used a gooey tar based sealant that does not harden.

Sold as a Kit as Pictured.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds. 390 and 427-4V engines without exhaust heat risers. That kit would include a studded bolt for the heat shield. See item 41282.

Reproduction fender fastener kit for Mercury Cougar Standard and XR7.

Reproduction Fender Extension Stud & Nut Kit for the 67 - 69 Cougar or Mustang

Fits Standard and XR7

New improved set of 6 screw for the glove compartment hinge on all 1967-68 Mercury Cougar and Ford Mustangs. Three 10-24 bolts with 0.72" conical washer heads to go into dash, and three 10-24 bolts with 0.50" conical washer heads to attach to glove box door. This is an updated proper kit for 1967-68 Mercury Cougar and Ford Mustang glove box door hinge. All AMK bolts, but WCCC special recipe. 6 pieces as shown.

Reproduction grille mounting kit for the driver (left hand) and passenger (right hand) sides of the Mercury Cougar.

These reproduction hood and hinge bolts and U nuts fir both the Standard and XR7.

Fits 1967 and 1968 Standard or XR7

This is a Mustang kit and it includes 4 screws, 2 metal nuts, 2 self-threading plastic nuts and 2 anti-rattle bumpers as pictured.For Cougar, you need this kit plus 2 more plastic nuts, found here.

Correct Fit and finish for 1967, and works for 1968. Connects the overhead roof console to the mounting bracket. The only difference between the 67 and 68 kits are that the 67 screws are chrome and the 68 are zinc. The zinc will discolor over time, so we suggest using the 67 kit on a 68. Replaces Ford Part #: 519A58

This reproduction quarter panel extension fastener kit fits both the Standard and XR7.

Fits 1967 and 1968 Standard or XR7

Fits 1967 Standard and XR7

This kit connects the Overhead Console mounting bracket to the roof. Screw heads and clips differ slightly between 67 and 68. Replaces Ford Part #: 519B24, 519B38, 519B46

Special fasteners which hold firewall insulator to the firewall. Made of high-quality plastic. Sold in pairs Check out this video

Used for multiple applications. 7/8" from bend to center hole.

Bag of 25 reproduction j-nuts for the front fenders on the Mercury Cougar or Ford Mustang.5/8" from bend to center hole.

These reproduction fender splash shield bracket screws and J nuts fit both the Standard and XR7.

This flat nut has many uses, most commonly used on the 67 - 68 corral / walking cat headlight eyelid door assembly or the 69 - 70 quarter script. Can be used on anything that has a 3/32" stud. Can be used for many items on a variety of vehicles including the Mustang, Torino, Cyclone etc.Sold individually.

Flat nut for attaching the "Mercury" script on the front fender extension on all 1967-68 Mercury Cougars. 4 total needed for emblem installation on that fender extension. Also attaches the reproduction running cat emblem to the headlight door on 1967-69 Mercury Cougars.

Fits Standard and XR7

Reproduction Front Bumper Guard Bolts & J Nuts for the 1967 - 1968 Mercury Cougar 

Replaces Ford Part # 359747-S

Original style wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Replaces Ford Part #: C5ZZ-8287-A.

Used original wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Ford Part #: C5ZZ-8287-A.

This is actually the correct 2 inch screw for the 1968, as opposed to the 1 3/4 inch screw that would have come in the 67. With the added length this screw is less likely to pull out of the firewall than the 67 screw was. Fits Standard and XR7. Sold individually.

This 1967 Cougar gauge cluster hardware kit is helpful when trying to reassemble a driver side gauge cluster that has been reassembled previously with the wrong fasteners or some of the items are missing. Includes all items shown. The only difference between 1967 and 1968 is that the 1967 has a smaller hole in the speedometer lens for the trip odometer button.

Fits 1967 and 1968 Standard or XR7

Fits 1967 and 1968 Standard or XR7

1/4-20 nut with captured washer for installing grilles to headlight buckets. 3 per side, 6 total per car. Sold individually.

Reproduction bolts for the grille / headlight eyelid hinge that fits both the Standard and XR7 Mercury Cougar. Check out this video

Fits Standard and XR7 Check out this video

Fits 3 speed or 4 speed manual floor shifts. Sold individually. Check out our video on rebuilding your shifter below:

Features 274 pages / 750 photos/ 12,300 items / history / finishes / measuring and more. This book provides detailed information about the fasteners specified in assembly manuals and parts books. All 12,300 fasteners are referenced to a photo! Must have for anyone wanting to correctly put together a 1955-1973 FoMoCo product.

Screws and spring clips for the tank or reservior for vacuum system

Clip used to route the wiring harness along the driver side of the engine compartment.

This kit contains 500 hog rings, more than enough for two bucket seats and one bench seat.

Fits 1967 Standard and XR7

For use with hood dowel or latch part number C5ZZ-16929-A. Application 1967-68 Mercury Cougar, 1965-66 Ford Mustang, 1965 Falcon and Comet. Original Ford part numbers 33845-S8 & 351810-S8.

These reproduction hood latch support bolts fit both the Standard and XR7.

A modern touch to this classic muscle car look. This kit is the same Scott Drake "Shelby Style" Billet hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, machined billet aluminum top plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are Machined billet aluminum top plates and the deluxe is stainless steel. Common...

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...