1967 Mercury Cougar

This is the dual port version used on UNITS BUILT PRIOR TO MAY 17, 1967. There was also a single port version in the later part of 1967. These dual port units always leak at the port fitting (easily sealed with epoxy) and the one way check valve never functions properly. Our Western grade A tanks are rust free. Keep in mind we have units that are not as clean looking but still hold vacuum for about half the price. Ford part #C7WY-13A185-C.

This is the dual port version used on UNITS BUILT PRIOR TO MAY 17, 1967. There was also a single port version in the later part of 1967. These dual port units always leak at the port fitting (easily sealed with epoxy) and the one way check valve never functions properly. Our Western grade A tanks are rust free. Keep in mind we have units that are not as clean looking but still hold vacuum for about half the price. Ford part #C7WY-13A185-C.

This single port version was used in the latter part of 1967 and all of 1968. Keep in mind we have units that are not as clean looking but still hold vacuum for about half the price. Cougar part number C7WY-13A185-C headlamp vacuum reservoir.

Reproduction Universal Strap / Medium Wire Loom for the 1967 Mercury Cougar or Ford Mustang 

Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"

New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water shields, plus many other components that are fastened to the body. This box contains 60 individual strips of black non-hardening caulk.

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

Reproduction driver side (left hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03487-A.

Reproduction passenger side (right hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03486-A.

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

This screw / stud seems to always be missing. This stud is just a little longer than stock to allow installing the Hi-Po / 427 GTE air cleaner. Fit most Autolite 4V carburetors assembly. Zinc plated for years of service. Size: 4 1/2 inches 1/4-20 X 1/4-20 threads.

Stud that screws directly into the 289 exhaust manifold on most 1965-67 Ford 289 engines, including Mercury Cougar and Ford Mustang. Sold individually Zinc (dark silver)

Used 14x5-1/2" styled steel wheel for your mercury Cougar. One year only offering in this size with a total width of 6- 1/2", a 3-7/8" backspacing, and a very small 1-13/16" center hole. Will not fit 1968 or newer Cougars equipped with disc brakes as the wheel will not fit over 1968 and up disc brake calipers. Will not fit 1967 Cougars that have been retrofitted with newer single piston disc brakes. Shipped bare, without center cap or trim ring. Various conditions with minor blemishes, but no...

9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. Reproduction 14"x6" styled steel wheel with correct argent silver finish between the chrome spokes on the center for your Mercury Cougar. Gorgeous reproduction of the...

Reproduction 15x7 chrome styled steel wheel for your Cougar or Mustang. Technically correct for Mustang because of the holes being placed in the center of the arms instead of in the inserts like the Cougar, but will fit both vehicles. Gorgeous reproduction of the original 1968 Mustang styled steel wheel. Correct in every way except that the outer band is welded on instead of riveted to the center section. This wheel has a total width of 7", backspacing is 4" and the center hole is...

Reproduction chrome center cap with blue background and chrome Mercury man logo for the Mercury Cougar. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the...

Reproduction chrome center cap with red background and chrome Mercury man logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from...

Chrome center cap with Blue background and chrome walking cat logo for the Mercury Cougar. Better than original! New from Scott Drake. These quality center caps feature our high quality chrome bezels. Check out the details in our "Cougar" lens. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing,...

Reproduction chrome center cap with red background and chrome walking cat logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good...

For the purists out there we have a very limited amount of used moon crater visors that have no impressions, seam separation and minimal rust on the clips if any.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually.

Reproduction Moon Crater Sun Visor for the 1967 and 1968 Mercury Cougar / Ford Mustang. Visors are fully padded and covered with the correct textured moon skin to match the headliner. Sold as a Pair. Nugget Gold is not available in Moon Skin Crater, it is only available in a smooth vinyl.

This decal was sometimes placed on the dash face pad near the middle or right side, and sometimes on the sun visor.

This 4 1/2" long flexible drive cable connects the Bosch "sardine can" motor to the gear box drive assembly. Limited supply. Check out this vintage XR7G television commercial ...

Used support bracket for the hood latch on any 1967-68 Mercury Cougar. L shaped support bracket goes on top of the hood latch assembly. It also attaches to the radiator core support.Ford part number C7WY-16707-A.

Used strap or support bracket for the foam air conditioning vent tube going to the driver side A/C vent. The electrical assembly manual indicates that this strap bracket behind the dash on the driver side. Our findings from the wrecking yard show that 1967 is typically rubber coated, 1968 is bare steel. Please specify is you have a preference. The rubber coated ones will show some deterioration, plan on re-dipping or use as-is. Not exactly the same as the support for the passenger side.Ford...

Reproduction brake pedal hanger for manual brakes. Can be modified to work for power brakes.

This used brake pedal support bracket is the correct hanger for a 1967-68 Mercury Cougar or Ford Mustang with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint, unused condition. Ford part # C7ZZ-6501508-C. *NOTE* Manual brake supports are different. Manual brake supports have four threaded...

This used brake pedal support bracket or brake pedal hanger is for the Mercury Cougar or Ford Mustang equipped with power disc or drum brakes. We have carefully shown the mounting position of the pedal so you can drill your existing manual brake pedal hanger when converting from manual to power brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means...

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design. Two different sized brackets used, this is the larger one that is 1-3/4 inches wide. The bracket that goes in the corner above the switch panel is 3/32" less. It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend...

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the smaller design. Two different sized brackets used, this is the smaller one that is 1-21/32 inches wide. This bracket goes in the corner above the switch panel. The larger bracket is 1-3/4" or 3/32" wider. It was obvious what the original intent was on this design in that a tab on the L...

Reproduction set of 5 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design of the two and by far the superior. Replaces item # 31908Through 67-68, there were four different style brackets, you can see all four by following this link. ...

This often times missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design.Through 67-68, there were four different style brackets, you can see all four by following this link. ...

Reproduction set of 5 XR7 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. Our improved design is better than the original in that the tab extends into the rectangular recess in the dash bezel which anchors in MUCH more securely. Replaces item # 31907Through 67-68, there were four different style brackets, you can see all four...

Radio support bracket for 1967-68 Mercury Cougar and Ford Mustangs without consoles. Used on AM, AM/FM, and AM/8Track factory radios.Replaces parts #s C7ZA-18888-A & C8ZA-18888-A, as found in the electrical assembly manuals.

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

This is the right hand or passenger side spring that holds the rear license plate or fuel door in the upright position. Fits 1967-68 and 1971-73 Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-A

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.  

C7ZZ-5482-C This is a factory used sway bar for the Special Handling Package as found on with the 1967 and 1968 GT option. This bar was factory identified with a single 'Green' paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.

Used front sway bar, does not include any mounting brackets or end link kits. Ford part # C7WY-5482-A.

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...