1967 Mercury Cougar

Used " RED " brake indicator lens for the Mercury Cougar. This is the early 1967 lens that was taped to the back of the dash pad. The late 1967 through 1968 used a lens with a small metal housing.

Used " Red " brake indicator lens for the Mercury Cougar. This is for late 1967 through 1968 which uses the small housing. The early 1967 lens was taped to the back of the dash pad. The lens may have a slight arc to it due to the heat from the bulb over time.

You will not realize how yellowed your original is until you put it next to this new one. Correct for XR7 or standard 67-68 consoles. Note, these install much easier if you trim a small sliver off each of the four mounting tabs with a utility blade.

Good used lens, will need polished but no cracks or deep scratches.Check out the video below on our new gauge tester: ...

Good used clock dummy lens, will need polished but no cracks or deep scratches. Same lens as official clock lens for 1967-68 Standard Model Mercury Cougar but with the black plastic plug, not an open hole for the clock stem.Ford part number C7WY-10887- Check out the video below on our new gauge tester: ...

Used parking / emergency light warning light lens for the 1967 - 1968 Mercury Cougar. You can find the bulb needed for this light here.Lens sold without the spring, you can find it here.

Good used lens, will need polished but no cracks or deep scratches. Check out the video below on our new gauge tester: ...

Used XR7 fuel gauge lens. It will need to be polished but will not have deep scratches.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Good used lens, will need polished but no cracks or deep scratches.Check out the video below on our new gauge tester: ...

Used high beam indicator lens for the 67 XR7 Cougar.

Used " BLUE " high beam indicator lens for the Mercury Cougar. This is the early 1967 lens that was taped to the back of the dash pad.  The late 1967 through 1968 used a lens with a small metal housing. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in...

Reproduction amber parking light / turn signal lens. This was actually used on the 64 - 66 Mustang which used the amber lens and clear bulb, as compared to the 67 - 68 Cougar which used the clear lens and amber bulb. Sold without gaskets or hardware (see related items).Sold individually

Used grade "A" rear courtesy / opera light lens for the Mercury Cougar. The opera lights came as standard equipment on all XR7 Cougars, but were a popular option on decor and standard level interior Cats as well. These used lights are they very best we can provide, but will not be 100% mint. Check out our reproductions, they are VERY nice. This unit is sold individually. Ford part # C6VB-13B726-A.  *TRIVIA* Did you know that these units were originally used on the 1966 Lincoln? The...

Good used lens, will need polished but no cracks or deep scratches. Check out our video on dash removal and restoration below: ...

Good used lens, will need to be polished but no cracks or deep scratches. 1967 has a smaller hole in the lens for the odometer trip reset button than 1968 Check out the video below on our new gauge tester: ...

Good used lens, will need to be polished but no cracks or deep scratches. 1968 has a larger hole in the lens for the odometer trip reset button than 1967 Check out the video below on our new gauge tester: ...

Good used lens, will need to be polished but no cracks or deep scratches. Check out our video on dash removal and restoration: ...

Perfect in every detail down to the FoMoCo logo! Gorgeous reproduction made from high impact plastic. Make those sequential taillights come alive with these brilliant lenses. Sold individually, two required per car, left is the same as right. Replaces Ford part #C7WY-13450. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Good used taillight lens with no cracks or heavy scratches. With a little effort you can make a lens like this look new. For the best results use a three step polish like NOVUS. For decent results use a one step polish like Meguires. Sold individually right is the same as left on this application. Ford Part #: C7WY-13450. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

This taillight at first glance looks as good as our grade "A" lens but when it is held to the light you will see a few stress cracks. Most of the 67-68 Cougars on the road are this way and so are most of the lenses in our yard. This lens will not leak and will polish up just as good as our grade "A" lens. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer...

Used " GREEN " turn signal indicator lens for the Mercury Cougar. This is the early 1967 lens that was taped to the back of the dash pad. The late 1967 through 1968 used a lens with a small metal housing.

Used green dash turn signal indicator lens for the Mercury Cougar. This is for late 1967 through 1968 which uses the small housing. The early 1967 lens was taped to the back of the dash pad. The lens may have a slight arc to it due to the heat from the bulb over time. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

Used on both the speedometer and tachometer lens. Comes with plastic keeper / washer that connects it from the backside of the lens. Sold individually, two required per cluster. These are in used condition as shown and need restoration. This item may require epoxy. The mounting stud on rear may not be present. It is plastic and originally melted over.

Amps / Fuel gauge lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. There are 3 total retainers needed per bezel, two of this style and one for the temp gauge (they are notched for different placements). Ford called these retainers a 'mask'.Ford part number C7WY-10890- Sold individually, 2 required. NOTE: The amps / fuel gauge retainers have white painted tops,...

Clock and dummy lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Fits any 1967-68 Standard Model Mercury Cougar. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. There are 3 total different retainers needed per standard instrument cluster. Ford called these retainers a 'mask'. Ford part number C7WY-10890-

Speedometer lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Fits any 1967-68 Standard Model Mercury Cougar. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. There are 3 total different retainers needed per standard instrument cluster. Ford called these retainers a 'mask'. Ford part number C7WY-10890-

Speedometer lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. Almost the same as the Tachometer lens retainer, tachometer version has a clipped section shaped like a thumb nail on the edge. Ford called these retainers a 'mask'. Stamped C7WF-10894-S or C8WF-10894-S. Also C7WY-10890- NOTE: The speedometer retainer is different from the tach retainer, the tach retainer is...

Tachometer lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. Almost the same as the speedometer lens retainer, tachometer version has a clipped section shaped like a thumb nail on the edge. Stamped C7WF-10894-S or C8WF-10894-S. Also C7WY-10890 NOTE: The tachometer retainer is different from the speedometer retainer, the tach retainer is notched for the screw post...

Temp gauge lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. There are 3 total retainers needed per bezel, 1 of this style and 2 for the amp and fuel gauges (they are notched for different placements). Ford called these retainers a 'mask'.Ford part number C7WY-10890- NOTE: The temp gauge retainer is painted all black, the amp / fuel gauge retainers have a white...

TEMP / FUEL lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Fits any 1967-68 Standard Model Mercury Cougar. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. This one has a small crescent shaped notch in the rim to fit into the cluster bezel. There are 3 total different retainers needed per standard instrument cluster. Ford called these retainers a 'mask'. Ford part number C7WY-10890- ...

TEMP / FUEL lens retainer, Speedometer lens retainer, and clock retainer - used on the inside of the cluster bezel to shield the face of the gauge. Fits any 1967-68 Standard Model Mercury Cougar. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. There are 3 total different retainers needed per standard instrument cluster. Ford called these retainers a 'mask'. Ford part number C7WY-10890-

Complete used gauge lens retainer set. Used on the inside of the cluster bezel to shield the face of the gauges. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. Ford called these a 'mask'.Ford part number C7WY-10890-

Used parking / emergency light warning light lens spring for the 1967 - 1968 Mercury Cougar.Spring only, lens sold separately. 

Door lock latch lever, for driver or passenger side locks. Attach with an "E" clip on the rear side of the lock mechanism. Used "E" clip is included. We are going to say that these fit all Ford door locks 1965 through 1973 and beyond. *Note you will need to purchase or reuse your retainer clip for attaching the lock rod. Retainer clip not included, we have good used or reproduction clips, see related items.Ford number stamped C5AB-6221970-A or D2AB-6221970-AA  ...

These plates were really clean before they were sent out for restoration, you can get  your Oregon plates restored at http://oregonplates.com/NOTE: The plates and plate numbers pictured are exactly what you'll receive.

NOTE: This is a blemished (blurred) license plate. We're selling these at close to nothing for anyone who wants to use the backside for custom painting. The graphics were printed blurry...you can't tell from a distance but up close they're not high quality prints (see photos above).  This classy aluminum license plate features the WCCC running cat logo on a matte black background, with a slightly grainy texture. Works great for display at car shows, everyday beautification (in states...

Give your Cougar or Mustang that cool, classic look by adding these replica California black and gold license plates. These plates are favored by classic car owners everywhere, because they signify a rust free, restored classic car. These plates are real stamped aluminum with raised numbers and letters. Sold Individually.

NOTE: This is a misprinted license plate, please see photos above. The holes were accidentally printed over the real holes giving it a double blurred look (the Cougar graphic is fine). We're selling these at close to nothing for anyone who wants to grab a bunch as gifts or collectibles!  This classy aluminum license plate features the WCCC running cat logo on a matte black background, with a slightly grainy texture. Works great for display at car shows, everyday beautification...

This classy aluminum license plate features the WCCC running cat logo on a matte black background, with a slightly grainy texture. Works great for display at car shows, everyday beautification (in states where front plates are optional), for-sale pictures, and even as standalone wall decoration. Plus it makes a great gift for the Cougar lover who has everything else!

Used license plate holder and fuel door for all 1967-68 Mercury Cougars. Comes as shown, hinges inspected, will include used or new license plate plastic inserts. See our list of related parts, will need rubber bumpers.Replaces Ford part number C7WB-13393.

Sold individually.

Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Inglewood, California.  Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.

Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Portland / Beaverton, Oregon.  Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.

Good used license plate light socket and wiring pigtail from a 1967-68 Mercury Cougar. Good socket without damage or corrosion. We cut the single wire pigtail as close to the main tail light harness as possible. Easy single wire splice for the DIY Cougar owner.

This lid is about 17-1/2 inch in diameter. Identified by the wagon wheel like spokes in the stamping. 1967 Mercury Cougar and Ford Mustang with 289 engines. Additionally this lid was used for the Canadian export Cougars and Mustangs in 1968, they continued to use the open emissions system.

This lid is about 17-1/2 inch in diameter. Identified by the wagon wheel like spokes in the stamping. 1967 Mercury Cougar and Ford Mustang with 289 engines. Additionally this lid was used for the Canadian export Cougars and Mustangs in 1968, they continued to use the open emissions system. Nice clean lid with no holes or other noticeable damage.

This Ford engine blue painted lid, is about 16-3/4 inch in diameter. Identified by the spokes in the stamping. We get these lids with and without a center ring underneath. The ring can be removed with a bit of effort if you desire. There is a chromed version of this air cleaner lid that was found on 1967 and 1969 Mercury Cougar and Ford Mustang with S code 390-4V engines. Additionally this lid was used on 1969-70 Q code 428CJ or non-ram air Cougars and Mustangs. We believe that this lid was...

Concourse correct reproduction chrome GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. This is an extremely hard piece to find used, and even rarer in NOS form, but now we can offer you this new unit that is made from the original tooling! It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine,...