1967 Mercury Cougar

Nice reproduction 1967-68 Mercury Cougar console light housing with lens cover. Plug and play with wiring. Click on images to enlarge. ...

Pit free original rear console courtesy light for all consoles 67-68, does not usually come with a good lens as most are cracked, faded or missing. Casting number as seen on the back reads C7ZB-13743-A. Number imprinted on wire can be: C4VB-13757-A.

This light was used on 1967 - 1968 Mercury Cougar and 1967-68 Ford Mustang Consoles with the roll up door. Not for use on the XR7 console. Notice the light lens is painted white on one half unlike the reproduction lens that is all white.  Assembly will not come with a working bulb, you can find the correct 1891 replacement here, or grab an 1891 LED here. You can find a replacement lens here. ...

This light was used on 1967 - 1968 Mercury Cougar and 1967-68 Ford Mustang Consoles with the roll up door. Not for use on the XR7 console. Notice the light lens is painted white on one half unlike the reproduction lens that is all white.  Assembly will not come with a working bulb, you can find the correct 1891 replacement here, or grab an 1891 LED here. You can find a replacement lens here. ...

Good used light bar for the convenience control indicator lights on the 1967 Cougar dash face pad. Indicators lights are for belts, door, fuel and park.

"C" pillar courtesy light bulb which is also good for under under dash courtesy lights on 67 - 70 Cougars.

Original good used part with no cracks, but may be brittle from age. These really are getting hard to find in mint condition. For the money, the reproductions are every bit as good as the originals. They are also available in red and yellow.Replaces Ford part number C4VY-10B870-A.

Available in original blue light diffusers or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have, there are different numbers of diffusers (filters) needed for different years and models. Sold as a set of four. SOLD AS SET OF FOUR(4).67 - 68 Cougar Uses6 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) 2 - Oil Pressure Gauge (XR7)69 - 70 Cougar Uses5 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) ...

Available in original blue light diffuser or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have there are different numbers of defusers (filters) needed for different years and models. SOLD AS SET OF FOUR(4). 67 - 68 Cougar Uses 6 - Instrument Cluster (XR7 or Standard) 2 - Clock 2 - Oil Pressure Gauge 69 - 70 Cougar Uses 5 - Instrument Cluster (XR7 or Standard) 2 - Clock ...

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

Short Style glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Ford part number C5AB-14413-A1 Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

NOS Rand McNally Lincoln Mercury atlas and travel guide, originally distributed to customers through their local dealer. Includes state, city and "special maps" that include the US, Central America, Mexico and Puerto Rico. Also includes a special features section with points of interest.

NOS 12 page Service Department Important Warranty Facts brochure. These pamphlets were handed out at dealership to anyone who bought a Lincoln Mercury vehicle. It details everything you should know about basic, power train, steering, suspension and wheel warranties and explains exactly what was and wasn't covered by the dealership.  Issued in January 1967 LM-7664

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.

Reproduction wheel cylinder link pin. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Sold individually. Ford part number B7A-2042-A.

Reproduction set of wheel cylinder link pins. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place.Sold as a set of four.

Latch rod that links the door latch and the inside door handle, right or left side door. 1967 Mercury Cougar and Ford Mustang door latch rods have some slight bends, and a clip midway with a Phillips screw, compared to the 1968 version. Normally this rod was fabric covered. Used rod only, no retaining end clips. Replaces Ford part number C7ZZ-6521940-A. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar...

Manual control shift linkage assembly for a floor shift C-4 transmission in any 1967-68 Mercury Cougar or Ford Mustang.  Check out our video on rebuilding your shifter below: ...

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Linkage arm that attaches to the windshield wiper motor that is unique to the 67 - 68 Mercury Cougar and Ford Mustang. These are marked 7Z, among other things the slot is specifically indexed for the 67 - 68 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Reproduction trunk lock cylinder with keys for the 67 - 68 Mercury Cougar. Replaces Ford Part # C7SZ-6543505-A or C7SZ-6543507-B (Glove box/Trunk lock kit). Below are some basics about removing and replacing your lock cylinder and lock cover. When removing the cylinder from the lock housing this button must be depressed to allow the cylinder to slide out the front of the housing.  The only way to depress the button is to have the key in the cylinder and partially turned as if to...

A perfectly working, matched set of trunk and glove box locks with key is getting rather hard to come by these days. These two matching locks are guaranteed to work perfectly. Includes 1967 style glove box lock, 1967-68 Cougar trunk lock cylinder with one "Ford" cut key to the coded to the number imprinted on the glove box lock. This is a matching set with new key. 1967 glove box locks has square edges on the front of the lock. Starting in 1968 the lock had a rounded edge on the front. We also...

Includes two door lock cylinders, two door cylinder gaskets, two keys and one ignition lock cylinder.  Made by the original OEM supplier.  That being said, they do not make them like they used to. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.

Correct style nut with captured washer for attaching hood scoops, 1969-70 Mercury Cougar inside door handles, and 1967-68 trunk lock. Correct nuts would have been black phosphate, these are shiny gold as shown.

Rubber pad for installing the trunk lock mechanism to deck lid.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made.

Used locking pawl for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. This pawl is released and via the vacuum motor when the door is opened and the ignition is in the off position. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used original driver side (left hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522135-A.

Used original passenger side (right hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522134-A.

This deck lock housing has been carefully stripped, polished and triple plated. You can send yours in in advance as an exchange or pay the core charge and return your old one later. Do know once a multi-faceted part like this has been stripped, polished and replated, some of the crisp, sharp detail will be muted and it will never again look just like factory. If you have extra cores we are buyers, especially if your lock assembly is complete. Be sure and watch our video below to see how to...

[No Description Provided]

Used locking lever for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. Two required per car. Here is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory C code 289-2V V-8 engine. Rated at 200 Hp with 9.3:1 compression ratio in 1967. 1967 289 engine that may or may not have been in running condition when pulled. Guaranteed to be rebuildable, most of these will already be bored 0.030", and need more. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex...

Short rubber valve stem and cap for Ford wheels or any steel wheel with a 0.453" hole. Snap in style, sticks up 2 inches from wheel surface. These will work with all of our aftermarket Ford wheels especially with trim rings. These have the Dill 627 caps. Same as the 1960's cars.

375897-S White plastic 5/16" washer for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 2 per side, sold individually.

This part is installed on all XR7 fuel sending units and Cougars and Mustangs with the optional Convenience Control Package. Low quality off shore part that requires soldering to your fuel sending unit. This is a temperature sensing device that activates when the fuel level drops enough to expose the unit at which point the circuit is closed and the low fuel light comes on. Commonly referred to as a Thermister / Thermistor / Low Fuel Sending Unit.

Fits the 1967, 1968, 1969, 1970 and 1971 Mercury Cougar with the 390, 428, 428CJ, 428SCJ, 429CJ or 429SCJ. Replaces Ford Part #:C8OZ-7B535-AR

1967 Mercury Cougar only. These are wearable items, and we list this item for those folks who really wish to go 'Concours trailered'. These interchange from side to side, two per 1967 Cougar. We save the very nicest ones from low mileage cars. Even though these are select parts, we recommend that the ball joints and bushings be replaced. *Note – Can only be used with 1967 Cougar lower control arms C7WY-3468-C (ITEM # 15393). Anghel Restorations can rebuild 1964-73 Ford suspension...

Finally a quality reproduction lower control arm for the one year only 1967 lower control arm! Deigned to work with your existing articulated strut rod arms found only on the 1967 Mercury Cougar. *NOTE – Can only be used with 1967 Cougar lower control arms C7WY-3468-C (ITEM # 15393). Replaces Ford Part # C7WY-3078-A Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

You can use 1968 up to 1973 lower control arms on a 1967 only if you change the strut rod to the 1968 - 1970 style. We have the strut rods available in both new and used form. Replaces Ford part #: C8OZ-3078-A. Sold individually, right is the same as left. *NOTE* The Cougar only, 1967 only, lower control arm is not available in reproduction form but you can rebuild the originals so do not throw away your cores as they may prove to be valuable one day. Mustang never used the articulated strut...

Concours restored pair of 1967 Mercury Cougar lower control arms. Unique to 1967 Mercury Cougars only, and must be used with original articulated strut rods. 1967 Mustang and 1968-73 strut rods will not work with these specific lower control arms for the 1967 Cougars, all models. Price is for two lower control arms. We did a limited run of these through anghelrestorations.com Replaces Ford part number C7WY-3078-B. Having issues with wobbly or loose steering? Check out our video on sloppy...

Sold individually, right is the same as left.  NOTE* You can use the 1968 - 1973 lower control arms on a 1967 ONLY if you change the strut rods to the 1968 - 1970 style. We have the strut rods available in both new and used form. Find them here. Replaces Ford part # C8OZ-3078-A. Having issues with wobbly or loose steering? Check out our video on sloppy steering below.  ...

Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.

Set of two polyurethane bushings that insert into the rear side of the lower control arm. This set contains two bushings that measure 1 9/16 across the leading inside edge, and 1 5/8 across the outer rim.Note: These larger diameter bushings were used on Ford service replacement lower control arms. Typically found on Ford supplied lower control arms without the welded on jacking tabs.

Set of two polyurethane bushings that insert into the rear side of the lower control arm. This set contains two bushings that measure 1 7/16 across the leading inside edge, and 1 5/8 across the outer rim. Typically these bushings fit Ford factory installed lower control arms with the welded on jacking tabs. Note: These smaller diameter bushings were used on factory installed control arms. Service replacement control arms utilized 1-9/16 inch bushings.

[No Description Provided]

This part mates to and is held down by Golde #100 413 681. The Golde part number for the smaller, lower elbow guide is 100 413 664