1967 Mercury Cougar

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped holes for exhaust manifolds. These weigh 48 lbs. each, and cannot be combined with other items...

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. These cylinder heads are factory drilled and tapped for thermactos smog tubes. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust...

Single cylinder head from 1967 Mercury Cougar with 390-4V engine with California thermactor smog ports. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes. Current...

Used highly collectible Dan Gurney slot car racing track made by the Republic Tool and Manufacturing Corporation in Los Angeles California. Open box and lightly used. Both cars are intact, and the decals have been placed on the the vehicles and the track. Everything is good condition, but the cars have not been tested and the red car has had it's wheels painted. Other than that, this is a rare and truly great find. Features the Mercury Cougar Logo on front of the box.

Reproduction headlight knob, retainer & bezel, cigar lighter and ignition switch retainer.

These studs and nuts are used to repair the passenger side mounting studs. The studs need to be drilled out using a 1/4" drill bit. Once done, use a 2 part epoxy and install the stud. Make sure to avoid getting epoxy on the threads where the nut will be installed. Once dry, install the bezel into the dash and use a 3/8 # deep well socket to install the nut. CAUTION: Only tighten finger tight to avoid cracking or breaking the bezel.

Used metal dash support brace for all 1967-68 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 8-1/2 inches long. Viewed in the 1967 Osborn Body Assembly Manual on page 23. Replaces Ford part numbers C7ZB-6504672 or C7ZZ-6504672-A.

This 2 1/4" trim part installs directly above the steering column.

When removing this part resist the temptation to "open it up". Instead walk it off carefully leaving it in its factory position.

This unique to 1967 standard Cougar dash trim set is what outlines the gauge cluster face pad. It is unique to the 1967 standard Cougar as it is held in place by black Phillips Screws. The 1968 trim set is held in by clips. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent.

Used aluminum face pad moulding / trim four piece set for the Mercury Cougar.

This trim part starts to the upper left of the gauge cluster and continues on to the passenger side following the line of the upper padded dash.

Only for use on standard model Cougars with no A/C. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

Used dash face pad for the standard Mercury Cougar that is NOT equipped with air conditioning. This unit will be nice and will not have any cracks, but could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different color, find your local autobody supplier. They should be able to mix up a small amount of the exact color you need. This icon means that we're looking to buy...

This set of three woodgrain dash inserts for the Mercury Cougar equipped with A/C are the best of the best of which we can provide you with. These grade "A" inserts retain a rich, original looking finish and have not been subjected to prolonged damaging UV rays. We carefully match these under bright lights to ensure they match color wise. No scratches, dings or other blemishes, and all four toggle switch labels will be in place. Includes a brand new XR-7 emblem to make the dash really pop....

When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side. Check out our video on dash removal and restoration: ...

Used grade B driver side dash insert for the 67 - 68 XR7 Cougar. Will show some amount of fading and scratches. When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side. Check...

When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. The best way to judge just how much fading has occurred on the panel is to remove the emblem for comparison purposes. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side.Check...

Used grade B passenger side dash insert for the 67 - 68 XR7 Cougar. Will show some amount of fading and scratches. Emblem will most likely need to be replaced. When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. The best way to judge just how much fading has...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in black for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best version of this much needed...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in BLUE for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best version of this much needed...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in DARK IVY GOLD or DARK GREEN for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in DARK RED for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. Please Note: Color on these is inconsistent and never spot on...

Of the three covers used on the 67-73 Cougars we find this one the most difficult to use. Will Not Work On Badly Distorted Dash Pads. The problem is not with the product but rather the design of the original dash pad. Unlike the 69-73 pads the 67-68 pads are prone to warping (sagging) badly. Since this glue on shell is rather rigid you have to have a mostly straight pad to work with. Large cracks are no problem even if your pad is curling at the cracks, just break off the portions of your...

This used part comes carefully cut from a parts car and will include all mounting tabs. It is slightly different from the Mustang version as it has a different contour where the dash pad attaches. AC and no AC are the same, but 67 and 68 differ slightly in height of the area where the ashtray is installed.  

Excellent reproduction of the passenger side 1967-68 Mercury Standard Cougar "Cougar" dash panel emblem. Nice reproduction with locating pins that attach to the padded dash panel on the passenger side of all 1967-68 Standard model Cougars. The factory originally installed these emblems onto the padded dash panel, and melted over the pins to the back. Carefully remove the padded dash (clips or screws) and break off the melted tabs on the back of the emblem. Clean pad and reinstall the new...

Reproduction passenger side 1967-68 Mercury Cougar "Cougar XR7" dash panel emblem with chrome XR7 highlights. Nice reproduction with locating pins that attach to the woodgrain dash panel on the passenger side of all 1967-68 XR7's (excludes the special edition XR7-G models). The classic Cougar community voiced their opinion that the original emblems with satin silver was nice, but the chromed "XR 7" lettering in chrome makes the dash 'Pop' (see comparison photo above). The factory originally...

Excellent reproduction of the passenger side 1967-68 Mercury Cougar "Cougar XR7" dash panel emblem. Nice reproduction with locating pins that attach to the woodgrain dash panel on the passenger side of all 1967-68 XR7's (excludes the special edition XR7-G models). You can view the photo above for a comparison between the satin and chrome versions. The factory originally installed these emblems onto the woodgrain steel panel, and melted over the pins to the back. The rear section of that...

There are five of these on the RH side that hold your plastic dash to the metal understructure. These also hold on the map light. Sold Individually. Ford Part #: 376642-S. Reference from mercurycougar.net: Best guys to always talk to about Cougars...will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting things...

Reproduction heater dash plate for the 67 Cougar or Mustang. Included are the plate, 4 piece knobs and hardware. Keep in mind that this face plate has the pebble grain finish which was standard to Mustangs (Cougars had the smooth finish).Replaces Ford part number C7ZZ-18A651-B

This 25 watt Tri Axial design is a big improvement over the original whizzer cone design and is an exact fit. Sold individually, this is a 5" by 7" speaker commonly called a "football" speaker. 4 Ohm.  Replaces Ford part # C7AZ-18808-D. Check out this video

Great way to get more speakers without cutting or modifying your car. This system utilizes the studs used for mounting your defroster ducts. Rather cumbersome to install and requires taking much of your dash apart. Check out this video

Quality Kenwood speakers that features two 40 watt 3 1/2" coaxial two way speakers. this unit is a huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with in-dash factory AC or not. In Non-A/C cars, this speaker may partially crush the vent duct tube. Check out this video

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

This plate allows you to install (2) 3 1/2" speakers of your choice in place of the (1) original factory speaker in the dash of your Cougar or Mustang. This is the same plate used on the Kenwood and Pioneer Dual Dash Speaker kits. Check out this video

Features two 4 ohm 3 1/2" coaxial two way speakers. Huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with or without in-dash factory AC. In Non-A/C cars, this speaker may partially crush the vent duct tube. Check out this video

Good used dash toggle switch that operates the courtesy (rear opera) lights in the Mercury Cougar. These switches will have no rust or broken wires and the plastic toggle switch tips are sold separately. These used switches move freely and are guaranteed to work. The only real difference between the years, besides the size of the shaft, is the toggle switch tips. That is why we are offering both 1967 and 1968 versions. There are three versions of shafts used on the 1967 - 1968 XR7 toggle...

Good used dash toggle switch that operates the driver side (left hand) map light in the Mercury Cougar XR7. This switches will have no rust or broken wires, moves freely, and is guaranteed to work. Plastic toggle switch tip is sold separately. The only real difference between the years, besides the size of the shaft, is the toggle switch tips. That is why we are offering both 1967 and 1968 versions. There are three versions of shafts used on the 1967 - 1968 XR7 toggle switches and all three...

New old stock dash toggle switch that operates the passenger side (right hand) map light in the Mercury Cougar XR7. These switches will have no rust or broken wires and the plastic toggle switch tips are sold separately. These used switches move freely and are guaranteed to work. The only real difference between the years, besides the size of the shaft, is the toggle switch tips.  There are three versions of shafts used on the 1967 - 1968 XR7 toggle switches and all three feature the same...

Good used dash toggle switch that operates the passenger side (right hand) map light in the Mercury Cougar XR7. These switches will have no rust or broken wires and the plastic toggle switch tips are sold separately. These used switches move freely and are guaranteed to work. The only real difference between the years, besides the size of the shaft, is the toggle switch tips. That is why we are offering both 1967 and 1968 versions. There are three versions of shafts used on the 1967 - 1968 XR7...

Good used dash toggle switch that operates panel (under dash) lights in the Mercury Cougar XR7. This switches will have no rust or broken wires, moves freely, and is guaranteed to work. The only real difference between the years, besides the size of the shaft, is the toggle switch tips. That is why we are offering both 1967 and 1968 versions. Plastic toggle switch tip is sold separately. There are three versions of shafts used on the 1967 - 1968 XR7 toggle switches and all three feature the...

Reproduction engine code decal for the 1967 - 1968 Cougar or Mustang equipped with the 289 2 barrell engine with manual transmission.

Reproduction engine code decal for the 1967 - 1968 S code - 390-4V or 390GT with automatic transmission, Cougar or Ford Mustang.

Reproduction engine code decal for the 1967 - 1968 S code - 390-4V or 390GT with manual transmission, Cougar or Ford Mustang.

A/C compressor clutch decal for Mercury Cougar and Ford Mustang.Replaces Ford Part #: C7AA-2987-D.

Replaces Ford Part #: C7ZZ-19959-A.

This is a reproduction of the original orange engine displacement decal with black lettering and black and white checkerboard on each end that was located on the top of the air cleaner.Fits the following models with a 289 High Performance engine:1967 Mercury Cougar1967 Ford MustangThe 289 Hi-Pro motor was never offered in the Cougar as an option but you could order an over the counter unit. ...