1967 Mercury Cougar

Power Steering hose bracket insulator for both the small and big block brackets for the 1967 - 1970 Mercury Cougar and Ford Mustang. Replaces Ford part #: C7ZZ-3A609-A or C7ZZ-3609. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are things coming to? Where is...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This kit fits the 1967 with a 1/4" control Valve Pressure fitting. You might want to verify that your 67 has the 1/4" fitting as many have been upgraded the the 5/16" fitting. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to...

These are the best CONCOURSe radiator hoses on the market. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. They have imprints that are very crisp and authentic. Each imprint is CONCOURSe correct. Includes Authentic Logo. c7ze-8260-a and c7ze-82-86-a.

New silicone radiator hoses for the 67 - 68 Cougar or Mustang with the 289 or 302 engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Used on both the 20"...

New silicone radiator hoses for the 69 - 70 Cougar or Mustang with the 390 or 428CJ engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Replaces Ford...

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co, also approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct for the specific application year. Represented by an oval...

Reproduction Concours correct windshield washer hose with ribbed outer wall. Hose is 101" and is cut-to-fit. Tee connector not included, you can find it here. You can find the nozzles here.

This hard plastic black cover, or shield, attaches just below the radiator and protects the headlight vacuum hoses that attach to the left and right headlight door actuators. This used part will be free of cracks but will be warped. With patience and heat they can be successfully massaged back to their original form. Must have detail item for a nicely restored early Cougar. For use on non-AC cars only. Replaces Ford part number C7WB-14A088-A.

No, zip ties were not used from the factory to secure the AC hoses to the shock tower braces . . . Four required per car, sold individually. Replaces Ford part #: C7ZA-430.

No rust or modifications, still has good white paint. The main difference between the 67 and 68 versions is the wiring color engravings on the backside are different between the two. Condition of the housing cannot be guaranteed. Ford casting number C7WF-10843-B Check out our video on dash removal and restoration: ...

Used rear driver side (left hand) courtesy / opera light housings for the Mercury Cougar. The rear courtesy / opera light was standard on all XR7 Cougars, but were a popular option on decor and standard level interior Cougars. These units are marked LH for the driver side and RH for the passenger side and are sold individually. Also sold as a PAIR. Ford part # C7WB-13B729-C or C7WY13A744-C for the passenger side, C7WB-13B736-C or C7WY-13A744-D for the driver side. *TRIVIA* Did you know that...

Used rear passenger side (right hand) courtesy / opera light housings for the Mercury Cougar. The rear courtesy / opera light was standard on all XR7 Cougars, but were a popular option on decor and standard level interior Cougars. These units are marked LH for the driver side and RH for the passenger side and are sold individually. Also sold as a PAIR. Ford part # C7WB-13B729-C or C7WY13A744-C for the passenger side, C7WB-13B736-C or C7WY-13A744-D for the driver side. *TRIVIA* Did you know...

Used rear driver side (left hand and passenger side (right hand) courtesy / opera light housings for the Mercury Cougar. The rear courtesy / opera light was standard on all XR7 Cougars, but were a popular option on decor and standard level interior Cougars. These units are marked LH for the driver side and RH for the passenger side. Also sold individually, see related items. Ford part # C7WB-13B729-C or C7WY13A744-C for the passenger side, C7WB-13B736-C or C7WY-13A744-D for the driver side....

New front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. Needs threaded studs, see related...

Used front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. May or may not have threaded studs, or...

Used grade A spinner / wheel cover ornament cap. These were sold over the counter starting in 1968 as an add on to your existing hubcaps (will not fit Gurney style caps). Even though this is graded as an A, do know the center will be faded or possibly repainted. Grade A centers will not be pitted or have cracked plexi. The Ford part # as seen on the box is C8WY-1130-A, casting number as seen on back reads C8WA-1A041-A. Does not include the cap itself. ...

This NOS kit was sold over the counter starting in 1968 as an add on to your existing hubcaps (will not fit Gurney style caps). The Ford part # as seen on the box is C8WY-1130-A, casting number as seen on back reads C8WA-1A041-A. Sold as a set of four. This set will require drilling holes in your hub caps. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for...

Used simulated wire spoke hubcap / wheel cover that is in average condition with minor curb scrapes. Ford part # C7WY-1130-C.*NOTE* You will often see this same cap with the Mercury head center and a red background. This cap is not correct for Cougar, but was found on other Mercury products such as the Montego.

Brand new FoMoCo simulated wire spoke hubcap. We do not have the original packaging for these at present. Ford part # C7WY-1130-C.*NOTE* You will often see this same cap with the Mercury head center and a red background. This cap is not correct for Cougar, but was found on other Mercury products such as the Montego.

Reproduction dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. There are no less than three versions of this reproduction unit on the market. This one, in my opinion, is the best option. The hue is not as brilliant as the original, but a very nice cap for the fit and finish that it offers. We have trim rings available too! Check out our video on Legendary Wheels below: NOTE: These are for use on the Legendary Series Eliminator wheels Fits:...

Used grade A "dog dish" style hubcap that will show minimal or no paint loss / fading and no dings. Most early Cougars used the full hubcap / wheel cover, so this one is rarely found on a Cougar. We have seen these used on wheels painted the body color on basic Cougars as well as black painted wheels.Ford part # C8MY-1130-A

Used dog dish style hubcap that will show paint loss / fading and at least one ding on our grade B driver quality example. Most early Cougars used the full hubcap / wheel cover, so this one is rarely found on a Cougar. We have seen these used on wheels painted the body color on basic Cougars as well as black painted wheels. Ford part # C8MY-1130-A

Excellent condition NOS "dog dish" style hubcap. Most early Cougars used the full hubcap / wheel cover, so this one is rarely found on a Cougar. We have seen these used on wheels painted the body color on basic Cougars as well as black painted wheels. Ford part # C8MY-1130-A

Used simulated wire spoke hubcap / wheel cover that is in average condition with minor curb scrapes. Most Cougar s were equipped with the black center medallion from the factory but when sold as an over the counter accessory often the red center caps were sold to Cougar owners. If you have black centers and would like to exchange them for our red centers we would be happy to oblige! Ford part # C7WY-1130-C.*NOTE* You will often see this same cap with the Mercury head center and a red...

Used sports special turbine / Dan Gurney Special hubcap / wheel cover. Grade A, No obvious scratches but the paint will show age. Ford part # C7WY-1130-F.*NOTE* You can often find a hubcap like this with the Mercury Head center. This is not correct for the Cougar, but rather the Montego, the foil decal in the center can easily be removed.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar ...

Used sports special turbine / Dan Gurney Special hubcap / wheel cover. Grade B, driver quality, will have curb scratches.Ford part # C7WY-1130-F.*NOTE* You can often find a hubcap like this with the Mercury Head center. This is not correct for the Cougar, but rather the Montego, the foil decal in the center can easily be removed.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar ...

Used grade "A" hubcap / wheel cover for the standard Mercury Cougar. These grade "A" units will not have curb rash, dings and the paint will not be faded out and will be nearly or completely intact. These caps are ones that were most likely take off early in life and stored in doors properly.Ford part # C7WY-1130-A. ...

Used grade "B" hubcap / wheel cover for the standard Mercury Cougar. These grade "B" units will have some minor curb rashing, dings and the paint will likely be faded out and or missing in some spots. Ford part # C7WY-1130-A.

NOS hubcap / wheel cover that is new in it's original Ford box for your Mercury Cougar.Ford part # C7WY-1130-B This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash...

Used simulated wire spoke hubcap / wheel cover that is in above average condition with no curb scrapes. This listing is for someone who has removed their center from their current damaged cap and wants to save money by purchasing a cap with no center. The same cap was used on most all FoMoCo products including, but not limited to the Falcon, Mustang, Fairlane, Comet, Galaxie, Montego and LTD. Only the center logo changed from one car to the next. Ford part # C7WY-1130-C. ...

Used simulated wire spoke hubcap / wheel cover that is in average condition with minor curb scrapes. This listing is for someone who has removed their center from their current damaged cap and wants to save money by purchasing a cap with no center. The same cap was used on most all FoMoCo products including, but not limited to the Falcon, Mustang, Failane, Comet, Galaxie, Montego and LTD. Only the center logo changed from one car to the next. Ford part # C7WY-1130-C. ...

The POGO Stick works just like the larger Hustler stick but is much easier to ship. If you need more leverage you can just add a pipe for leverage. We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Check out our video below: ...

C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade A cans are far and few between as often folks like to use a pry bar as leverage to over tighten their belt. These cans will usually have...

C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade B cans will always have some minor to moderate damage that is cosmetic. If you are capable of doing some minor body work they can made to...

Grade A Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps. Our...

Grade B Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps....

Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.

Reproduction idle mixture screw caps for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All white plastic caps. These were the tamper proof type of caps as installed from the factory.

Import reproduction. Fits 1967-70 Mercury Cougar or Ford Mustang without power steering. Rarely do these last the life of the rest of the front suspension, if you get 40,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Click on images to enlarge. ...

NOTE - Some customer are experiencing problems with this economy idler arm, the castle nut on top is causing clearance issues with the bolt on the top arm.Import reproduction. Fits 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 40,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering.

Premium grade of idler arm. Fits all 1967-70 Mercury Cougar and Ford Mustang. If you have loose / sloppy steering, replacing this part could help tighten things up. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Drag link hole size: 5/8" Customer feedback: Hey, just wanted to thank you for your prompt service. Last Friday...

Sold individually # 377112-S

This used emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

Air conditioning belt tension pulley. For Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C7AZ-8678-B. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. ...

NOS New Old Stock air conditioning fixed idler pulley for all 1967 Mercury Cougar and Ford and Mustang, all with 390 engines. Ford part number C7SZ-8678-B.

Used bracket and pulley assembly for Cougars and Mustangs with the 289 or 302 engine built after 3/1/1968. All pulleys are sold with new bearings installed.  If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! We also offer a bearing replacement service to rebuild your 289 or 302 fixed idler pulley, see item 27539. Replaces part # C7AZ-8678-C. ...

Air conditioning fixed idler pulley for Ford or Mercury with the 352 / 390 / 410 / 428 engines. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C5AA-8A919-C and C5AZ-8678-C ...

Used bracket and pulley assembly for 1967 Cougar or Mustang with 390 engines. All pulleys with bearings are sold in working used condition. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got the parts you need! Ford part # C7SZ-8678-B. ...