1967 Mercury Cougar

C7ZZ-65222A89-A Mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Driver side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21547-A.

C7ZZ-65222A88-A Mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Passenger side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21546-A.

Insert to replace the worn rubber and felt channel guide for the door glass in your cool Cat or precious Pony. These units feature original looking felt. Top molded pieces are bonded securely and has steel inserts for added strength. Sold in a pair. There are three brands of this particular piece, we carry the best even though our price is less than most everyone else. Replaces Ford part #C7ZZ-6521546-A and C7ZZ-6521547-A. Check out our handy diagram below to find other '67-'68 door parts you...

Reproduction clear seven piece glass set for the Mercury Cougar. This set consists of a clear driver side (left hand) and passenger side (right hand) vent / wing window, a driver and passenger side clear door glass, a driver and passenger side clear quarter glass, and a clear rear glass.This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on...

Reproduction six piece clear glass set for your Mercury Cougar. This set does not come with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked...

Reproduction seven piece tint glass set for the Mercury Cougar. This set does not come with any window trim so save your for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the...

Reproduction six piece tinted glass set for the Mercury Cougar. This set does not come with any window trim so save your for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is this tinted version that will have a slight green tint to the glass, other wise know as Sun-X Tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are...

This reproduction tape is a must for anyone replacing their stainless steel window trim pieces on the 1967 - 1968 Cougar or Mustang. Can be used on any of the side windows. We suggest saving the original quarter window rubber surround if possible, due to the curves, but this tape can be used there as well if needed. This glass setting tape is designed to look and perform similarly to the original Ford factory material. It creates a water tight bond as well as...

1967-1968 15 amp Buss style glass tube fuses sold in a package of 5 and used for the turn signals. This fuse is not located in the fuse box, but rather in an in-line fuse holder coming off of the turn signal switch on the steering column about 2.5 inches down after the plug.

1967-1970 7.5 amp Buss style glass tube fuses sold in a package of 5 and used for courtesy, glove box, luggage compartment, clock, tachometer, and radio pilot lights. Fuse length 7/8"

Early 1967 style glove box catch. Fits all 1967-68 Cougars and 1966-68 Mustangs.Replaces Ford part number C6OZ-6206064-A.

Used glove box catch for any 1967-68 Mercury Cougar or Ford Mustang. Several versions of this catch were used 1967-68, this is the most common version. Replaces Ford part number C6OZ-6206064-A.

Fits 1967 and 1968 Standard or XR7

Fits 1967 and 1968 Standard or XR7

Fits either 1967 or 1968 Mercury Cougar or Ford Mustang. Technically this is a copy of the 1967 factory installed version. 1968 factory glove box liners have a smooth section for installing the tire pressure decal. See the related items for 1967 and 1968 good used liners. Replaces Ford part #: C7ZZ-6506010-A.

Used glove box liner or plastic box for any 1967 Mercury Cougar or Ford Mustang. This is the same as the Scott Drake reproduction, but it lacks the smooth section for the tire pressure decal which was introduced on the 1968 cars. Used part with no cracks or heavy scratches. Inside clip usually has light rust. 1967 and 1968 glove box liners fully interchange, Replaces Ford part number C7ZB-6506010-A.

Used glove box liner or plastic box for any 1968 Mercury Cougar or Ford Mustang these do have the flat smooth area for installing the tire pressure decal. This is nearly the same as the 1967 used and Scott Drake reproduction, which lack the smooth section for the tire pressure decal. Good used part with no cracks or heavy scratches. Inside clip usually has light rust. 1967 and 1968 glove box liners fully interchange.Replaces Ford part number C8ZB-6506010-A.

A great optional accessory. All new tooling was created to produce these glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Replace Ford Part #: C6DZ-6506072.Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges.

A great optional accessory. All original glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Technically the lock style is for 1967, notice the push button with square edge? 1968 push buttons had rounded edges. See related for reproduction and 1968 used.

A great optional accessory. All original glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges. See related for reproduction and 1967 used.

Ready to move into the Cougar big time? Well now's your chance with this flashy gold plated money clip emblazoned with the XR7-G shifter emblem. A great item to add to your collection of memorabilia, or to actually use! We're not sure of it's exact origin, but we though we'd pass on the opportunity for someone to get their hands on it. Circular center measures 1-1/2" across.

Reproduction grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. Replaces Ford part # B5A-1131.

This is a front brake grease dust cap tool. No more dented caps. These are milled from 6061 solid aluminum.

Very rare to find one of these that has never been tapped in the slightest. We have a very limited quantity of grade A centers in stock. Ford part # C7WY-8A047-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

The majority of our centers look like the rust free part you see pictured. They will need some minor body work before paint. We will not send you junk! Ford part # C7WY-8A047-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Good used part with no pitting or obvious damage. Includes stamped steel metal mounting bracket attached to the backside. Cougar part numbers: C7WY-13A137-B (Headlamp exterior cover) C7WY-13A155-A (Headlamp hinge) Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

NOS part that shows shelf wear and may need to be repainted in places. For 1967 and early 1968 Cougars built prior 12/15/1967. Can easily be made to fit 1968. Ford part numbers: C7WY-13A137-B (Headlamp exterior cover)C7WY-13A155-A (Headlamp hinge) Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Good used eyelid with no pitting or obvious damage and is for 1967 and early 1968 Cougars built prior 12/15/1967. Includes emblem and metal mounting plate. Ford part # C7WY-13A136-B (Headlamp exterior cover) C7WY-13A154-A (Headlamp hinge) Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

1/4-20 nut with captured washer for installing grilles to headlight buckets. 3 per side, 6 total per car. Sold individually.

Complete set of re-chromed grille bars ready to paint and install. Show quality, restored from grille parts with minimal or no pits, bends or cracks. Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating.  If you pay the core charge and we send your...

Used driver side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 4 screws and grind down 16 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Replaces Ford part...

Used driver side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 2 screws and grind down 2 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Small section with two...

Used passenger side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 4 screws and grind down 16 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Replaces Ford...

Used passenger side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 2 screws and grind down 2 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Small section with two...

Reproduction bolts for the grille / headlight eyelid hinge that fits both the Standard and XR7 Mercury Cougar. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

One of the most common problems with first-generation Cougars is droopy hidden headlight eyelids, which make the otherwise iconic front grille look like an eyesore. This inexpensive and easy to install kit provides stops for the eyelids to rest against in the closed position. It also provides some extra structural support to take some of the pressure off the built in bump stops. The vacuum actuators on these cars create extreme downward pressure at all times when running, causing the upper...

High quality reproduction of the chrome rectangular "corral" emblem surround for the passenger side grille / headlight cover on a 1967-68 Mercury Cougar. Unlike the original, which had the 4 studs peened over on the back side of the grille, this new one attaches with 4 clips (included). See also the background decal and walking cat emblem to make this a complete assembly. We also sell this as a complete kit. ...

Fits Standard and XR7 Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

This kit is for the 1967 Cougar, we also list the Early 1968 and Late 1968 versions. There are minor differences in each one. This basic kit will save you many hours on your grille restoration especially if you do not own a bead blasting cabinet or the specialty power tools needed to separate the chrome grille bars from the grille assembly. To come up with this "near perfect" group of parts we have to disassemble several West Coast, corrosion free grilles and inspect them very closely. Next we...

Used grade "A" driver side (left hand) grill section for the Mercury Cougar. 1967 is unique from the 1968 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and found to be free of large cracks, has good chrome with no pits or major scratches and is not severely warped. Hairline cracks will be present in the area of the painted...

Used grade "A" driver side (left hand) grill section for the Mercury Cougar. 1967 is unique from the 1968 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and may have some minor cracking, but the chrome will not have pits, major scratches, and will not be severely warped. It will have a misalignment issue as they all do in the...

Used grade "C" driver side (left hand) grille section for use as a patch for those with a break in the section that continues to the fender. Watch the video below to see how to fix your current grille and save a lot of money. Check out our video on grille repair below: ...

Used grade "A" passenger side (right hand) grill section for the Mercury Cougar. 1967 is unique from the 1968 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and found to be free of large cracks, has good chrome with no pits or major scratches and is not severely warped.  Hairline cracks will be present in the area of the...

Used passenger side (right hand) grill section for the Mercury Cougar. 1967 is unique from the 1968 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and found to be free of pits or major scratches in the chrome and is not severely warped. It will have a misalignment issue as they all do in the portion on the outer most corner...

Used grade "C" Passenger side (right hand) grille section for use as a patch for those with a break in the section that continues to the fender. Watch the video below to see how to fix your current grille and save a lot of money. Check out our video on grille repair below: ...

Good used grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. This part will not have any missing "chunks" but will show hairline cracks most evident where the heater core tubes pass through. The engineering number imprinted on the back side of this grommet taken from a 1967 Cougar is C7ZA-19B588-A. Good through mid year 1969. Compare to the 1970 item pictured for selection on your late 1969 Cougar.Please indicate in the Order Notes...

Premium reproduction rubber grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Molded rubber exactly like the original! Other reproductions on the market are die cut from sponge rubber sheets and nothing like the original. * Note - Used starting during the early part of 1969. Compare the evaporator line orientation for both years. ...

Reproduction rubber grommet for the air conditioning case. This grommet encloses the tubes for the evaporator, and slides into a slot on the heater box. Fits 1967-1969 Mercury Cougar and Ford Mustang. 1969 owners, please compare your grommet to the picture, late 1969 changed to a triangle shaped grommet. Please see related items for late 1969-73 rubber grommet. Replaces Ford part number C7ZZ-19B552-A. Check out our videos below on how to replace a heater core! We now have separate videos for...