1967 Mercury Cougar

Made from fuel resistant cork like original. This gasket is specific to 1967 - 1968 Cougars. We finally found the correct gasket with correct hole placement (our other version which is good for Cougar AND Mustang has five holes, so basically you would have to drill through the cork just like they did in the Dearborn and San Jose factories).Here's a good tip! Ken Stein gave us this one...Install two of these gaskets and your gas cap will not scratch your paint. Original gas caps will always...

Made from fuel resistant cork like original.  Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...

Replaces part #C0AF-9276-A. Goes between fuel sending unit and tank.

This gasket goes between the rear axle flange and the backing plate on the differential. It fits all Mustangs from 1967 - 1970.

Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.

This gasket is found behind the trunk lock housing, which the lock itself sits in behind the trunk lock cover plate, and forms a seal between the trunk lock housing and the trunk itself. Made of soft rubber much like the original. Replaces Ford part #: C7WY-6543625.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.

Gasket for mounting the oil filter adapter to any FE or Ford 360, 390, 410, 427, 428CJ engine. Name brand gasket, fits all 1967-70 Mercury Cougar or Ford Mustang with S, X, R, Q, or W code engines.

OEM Cork Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.

Rubber Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.

New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.

Thermostat Housing Gasket BY FEL-PRO® Replaces Ford Part #: C5AZ-8255-A.

Thermostat Housing Gasket By FEL-PRO® for the Big Block. REplaces Ford Part #: C7ZZ-8255-D.

New water pump plate gasket for the Mercury Cougar or Ford Mustang.

New water pump gasket for FE Ford engines. 1967-70 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. Single gasket, two gaskets needed for installing your water pump. Price is for one gasket only.

New water pump gasket for 1967-69 Mercury Cougar and Ford Mustang with 289/302/351W. Single gasket for sealing water pump to water pump plate only.

Made from durable black plastic with correct ridged edges. Includes all four gaskets, enough for both the left and right exterior door handles. Replaces Ford part numbers C7ZZ-6522428/9.

If you're going to rebuild your engine, this is the item you'll want to get. It's the complete gasket set for your 289 and 302 engines. (Will not fit early Boss engines). Included in this kit are the following: Head Gaskets Intake GasketsOil Pan Gasket Rear Main SealExhaust Manifold Gaskets Valve Cover Gaskets Water Pump GasketsTiming Cover Gaskets Timing Cover SealWater Neck GasketFuel Pump GasketDistributor Gasket ...

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1967-70 big block Ford engines with size 390, 427, or 428 cubic inches, FE engine only. 1967-70 Mercury Cougar, Ford and Ford Mustang.

New timing cover gasket set for 1967-70 Mercury Cougar and most all Fords with 289/302/351W engines. Gasket set includes; timing cover gasket, crankshaft seal, water pump gasket for early or late water pumps, and the oil pan corner gaskets under the timing cover.

New timing cover gasket set for the 1967-70 Mercury Cougar and most Fords with 390-2V, 390-4V, 427-4V, and the 428 Cobra Jets. Gasket set includes; crankshaft seal, timing cover gasket, two water pump gaskets, fuel pump gasket, and oil pan to timing cover gasket.

Cork valve cover gaskets for any big block Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Rubber valve cover gaskets for any FE 390 or 428 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Sold as a pair. These seal the lens to the taillight bucket / backing plate. Also used on the 1967 Shelby. Replaces Ford part # C7WY-13461.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Cork valve cover gaskets for any 289/302/351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

Rubber valve cover gaskets for any 289 302 351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

Good used lens, will need polished but no cracks or deep scratches.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Background paint is not sun damaged and is guaranteed to work good. If your gauge is cosmetically fine you may consider purchasing our grade B version and using your existing gauge face as they are easy to change out.Clean tested and working gauge that will be undamaged by the sun. Our instrumentation technician inspects, cleans, and zero's out the gauge. Check out the video below on our new gauge tester: ...

Clean tested and working gauge that will be undamaged by the sun. Our instrumentation technician inspects, cleans, and zero's out the gauge.Check out the video below on our new gauge tester: ...

Functions well but face is faded. It is easy to replace this face with your existing good face.Check out the video below on our new gauge tester: ...

NOS gauge for any 1967-68 Standard Model Cougar. This combination gauge is a fuel and temperature gauge all in one with an oil and amp "idiot" lens on either side. Both gauges are guaranteed to work good. New Old Stock gauge or 'pointer dial' as the box says. NOS C7WY-9280-A. Check out the video below on our new gauge tester: ...

Comes with lens, background paint is not sun damaged. Guaranteed to work good. If your gauge is cosmetically fine you may consider purchasing our grade B version and using your existing gauge face as they are easy to change out.Check out the video below on our new gauge tester: ...

This gauge works fine but the paint has gone bad. You can use your existing good face to combine with this gauge and save money.Check out the video below on our new gauge tester: ...

Good used lens, will need polished but no cracks or deep scratches.Check out the video below on our new gauge tester: ...

Guaranteed to work good. If your gauge is cosmetically fine you may consider purchasing our grade B version and using your existing gauge face as they are easy to change out.Check out the video below on our new gauge tester: ...

Works good but paint has gone bad. Use this gauge with your current good gauge face to save money.Check out the video below on our new gauge tester: ...

Guaranteed to work good. If your gauge is cosmetically fine you may consider purchasing our grade B version and using your existing gauge face as they are easy to change out.

These are original amp meters converted from reading amps to reading volts. Includes New XR7 Amps overlay made from top quality 3M 467MP and use 200MP adhesive. The longer 200MP adhesive is in place the stronger it binds. Lens has had the "amps" buffed off. Optional Volt decal is included. Core charge includes both lens and amp meter. Core charge will not be refunded if either piece is missing. Click here for a article describing the advantages of a Volt Meter.  Replaces Ford Part #:...

This 1967 Cougar gauge cluster hardware kit is helpful when trying to reassemble a driver side gauge cluster that has been reassembled previously with the wrong fasteners or some of the items are missing. Includes all items shown. The only difference between 1967 and 1968 is that the 1967 has a smaller hole in the speedometer lens for the trip odometer button.

This is the background for your standard model Cougar Temperature and Fuel gauge. Often times this part will be damaged from prolonged exposure to sun. This is a grade "A" part with no blemishes.Check out the video below on our new gauge tester: ...

Set of four XR-7 gauge background decals that stick on directly over your old, faded originals. Includes fuel, temperature, amp meter and oil temp gauge decals.Check out the video below on our new gauge tester: ...

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

Used original Golde sunroof gear box. This box is found above the headliner on the passenger side.Golde part number 0142850 00

C7ZZ-65222A89-A Mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Driver side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21547-A.

C7ZZ-65222A88-A Mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Passenger side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21546-A.

Insert to replace the worn rubber and felt channel guide for the door glass in your cool Cat or precious Pony. These units feature original looking felt. Top molded pieces are bonded securely and has steel inserts for added strength. Sold in a pair. There are three brands of this particular piece, we carry the best even though our price is less than most everyone else. Replaces Ford part #C7ZZ-6521546-A and C7ZZ-6521547-A. Check out our handy diagram below to find other '67-'68 door parts you...

Reproduction clear seven piece glass set for the Mercury Cougar. This set consists of a clear driver side (left hand) and passenger side (right hand) vent / wing window, a driver and passenger side clear door glass, a driver and passenger side clear quarter glass, and a clear rear glass.This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on...

Reproduction six piece clear glass set for your Mercury Cougar. This set does not come with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked...