1967 Mercury Cougar

Dark Red / Maroon floor mats for the 67 - 73 Cougar embroidered with the XR7 logo.

Green floor mats for the 67 - 73 Cougar embroidered with the Cougar script logo.

These floor mats were available as part of the factory "protection package" or as a dealer accessory when these cars were new. Good used originals have gotten VERY hard to find. At present (9-20-18) they are only available in black. Keep in mind the 69-73 convertible used a narrower mat to clear the inner rockers. We have a diagram that shows you where to trim for your convertible. The walking Cougar logo is a favorite of any Cougar fan. The Cougar became so popular that soon after the Cougar...

Reproduction floor pan firewall extension for the driver side (left hand) of your 67 - 68 Cougar.

This piece runs under the floor over the transmission where the floor pan meets the firewall.

Reproduction driver side (left hand) floor pan to cowl side panel for Mercury Cougar and Ford Mustang. Normal 0 false false false EN-US X-NONE X-NONE Here's our little film to help you fortify your car! ...

Fits Standard and XR7

New fluorescent needle restoration paint for the gauges in your Mercury Cougar or Ford Mustang. Over the years, the sun has wreaked havoc on your Cat or Pony. This sun damage has also had it's way with the needles on you gauges and washed them out. This true fluorescent paint will not only make your needles look factory fresh, but will also bring back their glow at night. One jar contains 2.25ml worth of paint.

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

C7ZB-17664-A Foot operated electric wiper actuating device for engaging the windshield washer pump or to cycle your windshield wipers once manually in light rain. Ford MPC number C7ZZ-17664-A. For any 1967 - 1968 Mercury Cougar and Ford Mustang.NOTE: If your electrical points are fried, you can simply replace them with the used contact replacement kit. Please note the Core deposit ...

Windshield Washer Pump Pedal Pad for 1967-1968 Mustang & Cougar. Keep your foot from sliding off the pedal with this Injection-molded rubber pad with vertical grooves just like original. This pad was used on models with a floor mounted washer pump pedal. (7664A) This is almost always missing off of the end of your foot operated washer pump. Replaces Ford part number C7ZZ-17664-A. We also have good used pumps in stock. Thanks for the plug Mark!: My first deal with Don was clear back in the...

Reproduction rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1968 Mercury Cougar and Ford Mustangs. New part with a fine threaded stud, also called a pinion bumper. The correct casting number is seen on this rubber axle bumper is C3AA-4906-C, this version has fine threads. The version most often seen on the 1969-70 is C9OA-4906-A. It will have a course threaded mounting stud.

This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...

NOS pamphlet from the Ford Motor Company detailing the 24 month 24,000 mile, or 5 year 50,000 mile warranties for the line of 1967 Cars and light trucks including Falcon, Mustang, Cougar, Ranchero, Fairlane, Thunderbird, Bronco, Light Trucks, Comet, Continental and Econoline.Volume 67C16L6

Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan. Includes driver and passenger sides.

Reproduction driver side (left hand) inner front frame patch for Mercury Cougar and Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

Reproduction passenger side (right hand) inner front frame patch for the Mercury Cougar or Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

Brass and steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown. 

Brass and steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 20 piece set with threaded screw in plugs as shown. 

Complete air vent assembly with cable, knob and bracket ready to bolt to your cowl. Replaces Ford Part # : C7ZZ-6501934-A

Our good used vents will not have cracks in the plastic or a rusty flapper from a leaking cowl. These are the same for AC and non AC.Replaces Ford part number C7ZZ-6501935-A.

Core bench seat for the 1967 Mercury Cougar or Ford Mustang equipped with decor interior. The foam almost will always be deteriorating or even missing. All seat cores will be solid frames taken from a Western parts car. Seat tracks are sold separate.

Reproduction Front Bumper Guard Bolts & J Nuts for the 1967 - 1968 Mercury Cougar 

Reproduction front diaphragm for your 67 - 69 Cougar or Mustang Midland power brake booster.

All new disc brake pads are supplied to us by brand name manufacturers. Boxed set of four pads. Semi-Metallic linings. Kelsey Hayes Brake caliper system.

All new premium ceramic disc brake pads. Superior "positive mold" manufacture process provides better braking performance. OE designed shims ensure noise free operation. Ceramic brake pads are scorched to remove any impurities in the friction material. This eliminates the need for initial break-in and reduces the noise associated with pad glazing. Kelsey Hayes Brake caliper system.

Reproduction Front end rebuild kit specifically for the 1967 Cougar with articulated strut rod arms.There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be...

Reproduction full one piece front frame rail for the driver side (left hand) of the Mercury Cougar or Ford Mustang. Replaces Ford Part #: C7ZZ-6510219-B.Here's our little film to help you fortify your flexxy feline!

FULL inner and outer passenger side (right hand) reproduction one piece frame rail for the Mercury Cougar or Ford Mustang. Replaces Ford Part #: C7ZZ-6510218-B.Here's our little film to help you fortify your flexxy feline!

Reproduction driver side front inner apron for both the Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Good used brace that may be lightly rusted but not ripped, but will almost always show minor repairs. This part was straightened in a vise prior to taking this picture. At this price we do not sell mangled junk, but after 40 years it is rare to find one that has never been bumped. Ford master part # C7WY-13B135-A.

Good used brace that may be lightly rusted but not ripped, but will almost always show minor repairs. This part was straightened in a vise prior to taking this picture. At this price we do not sell mangled junk, but after 40 years it is rare to find one that has never been bumped. Passenger side ones have a much less survival rate than the driver side bracket, due to the proximity of the battery.Ford master part # C7WY-16B134-A.

Front Parking Light To Valance Pads are sold as a pair. Fits the 67 and 68 Cougar or 65 and 66 Mustang. Replaces Ford part #: C5ZZ-13217.

Early production brake lines were routed 'over' the steering column.

Looped weld in retainer for the rear seat installation on any 1967-70 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets. We think that the Ford number is C5AZ-6263370-B, but we have not been able to verify this for certain. For sure that basic Ford part number is 63370. ...

New Old Stock. This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

For power or manual drum brake Cougars. Late production brake lines were routed under the steering column.

For power or manual drum brake Cougars.Late production brake lines were routed under the steering column.

For power or manual drum brake Cougars.Early production brake lines were routed 'over' the steering column.

Early production brake lines were routed 'over' the steering column.

Reproduction 22" pigtail for the 67-69 front turn signal wiring harness. Please Note: The Cougars are wired differently than some Mustangs. On some Mustangs the brown wire goes to a male plug.   This plug is a reproduction of the Cougar plug. Here is an example from the reproduction tail light we sell showing the difference: For installation on a Cougar, match up: Black Wire Black Wire Light Blue Wire Light Blue / Off White Wire Brown Wire Brown Wire ...

***WARNING*** Plugging these directly into a Cougar wiring harness without correctly re-wiring in the pigtails may fry your wiring harness! Reproduction driver side (left hand) and passenger side (right hand) front turn signal / parking light assemblies for the Ford Mustang. The plug is not correct for the Mercury Cougar's wiring harness and will need to be changed to work properly. However, this is an easy straightforward process which we lay out below. Plus you can save a good amount of that...

Stamped steel and and zinc plated to prevent rust. Fits behind the parking lamps, sold individually. Replaces Ford part #: C5ZZ-13207-B.

Used driver side parking light / turn signal retainer. Ford part #: C5ZZ-13207-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Stamped steel and and zinc plated to prevent rust. Fits behind the parking lamps, sold individually. Replaces Ford part # C5ZZ-13206-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Used passenger side parking light / front turn signal retainer. Ford part # C5ZZ-13206-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Stamped steel and and zinc plated to prevent rust. Fits behind the parking lamps, Sold as a pair. Replaces Ford part #: C5ZZ-13206-B and C5ZZ-13207-B.