Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 1921-1968 of 5109
$0 Price: $18.35

Buy Details

Availability: In-Stock Item
Item #: 41077 -

This reproduction hood hinge nut and bolt kit fits both the Standard and XR7 and is sold as a kit as pictured. These connect the hinge to the hood itself, and connect the hinge to the fender apron.

$0 Price: $101.55

Buy Details

Availability: In-Stock Item
Item #: 11092 -

Improved reproduction right and left hand hood hinges for the Mercury Cougar and Ford Mustang. Much heavier duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. it will be easier to fit and adjust these hinges prior to installing the springs on them. We use an old section of...

$0 Price: $52.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19262 -

Used hood latch for a 1969 Mercury Cougar, it will fit the 1970 too. Starting in 1969 until 1970, Mercury had three different hood latches. This late 1969 version has the medium length handle. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number C9WY-16700-B.

$0 Price: $52.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19290 -

Used hood latch for a 1970 Mercury Cougar, it will fit the 1969 too. Starting in 1969 until 1970, Mercury had three different hood latches. This 1970 version has the longest handle, and is the easiest to operate. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number D0WY-16700-B.

$0 Price: $96.25

Buy Details

Availability: In-Stock Item
Item #: 14062 -

A modern touch to this classic muscle car look. This kit is the same Scott Drake "Shelby Style" Billet hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, machined billet aluminum top plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are Machined billet aluminum top plates and the deluxe is stainless steel. Common...

$0 Price: $63.35

Buy Details

Availability: In-Stock Item
Item #: 13779 -

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

$22.95 Price: $33.17

Buy Details

Availability: In-Stock Item
Item #: 42020 -

This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...

$0 Price: $25.97

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32039 -

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

$0 Price: $59.85

Buy Details

Availability: Out of Stock
Item #: 23563 -

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

$35.00 Price: $38.57

Buy Details

Availability: Out of Stock
Item #: 13850 -

This item has been discontinued until further notice.The High tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13832 or C9ZF-13801-B.

MSRP:$35.00
$35.00 Price: $28.67

Buy Details

Availability: Out of Stock
Item #: 13851 -

This item has been discontinued until further notice.The Low tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13833 or C9ZF-13802-C.

$0 Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 10867 -

Attaches behind the drivers side horn on all 1969-70 Mercury Cougar and Ford Mustangs with air conditioning. We believe that this part was installed to maintain clearance with the A/C condenser. Ford part number C9ZF-13925-A as seen in the 1969 Electrical Assembly Manual.

$0 Price: $43.65

Buy Details

Availability: In-Stock Item
Item #: 32359 -

Wire extension for horn relocation, when the drag pak or drag pack option was ordered typically with 3.91 or 4.30 rear axle ratio. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory oil coolers. Should also fit Torino and Cyclone. Reproduction of Ford part number C9DB-13A840-A.

MSRP:$149.85
$149.85 Price: $127.35

Buy Details

Availability: In-Stock Item
Item #: 10319 -

If you have already begun to install or have installed this item, it is not eligible for return or refund. This rim blow horn switch is made in the United States by Daniel Carpenter Mustang and is made from vinyl like original. When installing, make sure to massage the rim blow switch in place with counter clockwise, compacting strokes. Clockwise strokes (thumb motions) will stretch the switch and when you complete the installation you will find the part has become too long to fit in place...

$0 Price: $142.85

Buy Details

Availability: Out of Stock
Item #: 27375 -

Tested and working used pair of Hi and Lo tone horns. 1969-70 Mercury Cougar and Ford Mustang used part number C9ZF-13802-C and C9ZF-13801-B. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for your show car.

$0 Price: $28.75

Buy Details

Availability: Out of Stock
Item #: 13767 -

Aluminum flexible tube that connects the vapor canister to the air cleaner. To give this the look of the originals that had a black paper exterior coating you can spray paint it flat black. If anyone knows of a source to buy the original paper coated foil tubes we would like to hear from you. Fits 1970 California Delivered Cars and all 1971 - 1973 Cars. Look for Buck Tag EV or EM. Preheat/Emission Control Duct.3ft long 7/8" O.D. 3/4" I.D. Replaces Ford Part #: D1UZ-9d667-A, D4HZ-9d667-A...

$0 Price: $54.55

Buy Details

Availability: In-Stock Item
Item #: 19996 -

Black paper wrapped aluminum flexible tube that connects the vapor canister to the air cleaner. This is as close to concours as we can find, 3/4 inch diameter, 36 inches long, and black outside, brown paper color inside.  Fits 1970 California Delivered Cars and all 1971 - 1973 Cars. Look for Buck Tag EV or EM. Preheat/Emission Control Duct. Replaces Ford Part #: D1UZ-9d667-A, D4HZ-9d667-A or D0AZ-9D667-A

$0 Price: $25.15

Buy Details

Availability: Out of Stock
Item #: 13627 -

Reproduction Autolite gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A. ...

$0 Price: $8.25

Buy Details

Availability: In-Stock Item
Item #: 26659 -

This Gas Tank To Filler Pipe Hose reproduction fits the 67, 68, 69, and 70 Mercury Cougar. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

$52.16 Price: $94.85

Buy Details

Availability: In-Stock Item
Item #: 13721 -

High pressure hose from the insulator to the control valve. All correct ribbing, striping, and crimping. Has correct colored protective sheathing.  This hose is factory correct for the 1967-68 390, 427 and 428 & 1969-70 302, 351, 390 and 428. This hose can also be used to reroute the 1967-68 289 and 302 to the big block routing when paired with the other 3 hoses needed (C9OZ-3A319-A, C8ZZ-3A713-A, C7AZ-3A005-A) and the 69-70 power steering hose bracket (C7ZZ-3C510-A and...

$0 Price: $45.80

Buy Details

Availability: In-Stock Item
Item #: 53273 -

NOTE: Some customers have mentioned this hose does not fit well, others have said it fits with no issues. It is not the same as OEM and fitment seems to depend on the vehicle and modifications that have been previously done. We recommend going with our premium version. Lower pressure hose for any 1967-70 Mercury Cougar and Ford Mustang, but with a V-8. The factory power steering pressure hose originally was a two piece hose. Valve end has the 5/16" flared male fitting, and a 3/8" female...

$50.00 Price: $57.47

Buy Details

Availability: In-Stock Item
Item #: 42029 -

This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C. Click this link for more clarity on power steering hoses: https://secure.cougarpartscata... ...

MSRP:$50.00
$50.00 Price: $45.38

Buy Details

Availability: In-Stock Item
Item #: 42030 -

This Pump to Value Outlet Pressure Hose is 100% correct for the 1970 small block. This is the upper portion that connects to the one year only 1970 pump found on the 351c, 351w and BOSS 302 equipped cars. Like the originals, this is part one of a two part hose. This hose has industrial high pressure fittings that are much higher quality than those available by most Cougar / Mustang parts dealers. Replaces Ford Part #: D0OZ-3A319-A. Click this link for more clarity on power steering hoses:...

$0 Price: $19.15

Buy Details

Availability: In-Stock Item
Item #: 41911 -

Concours for 1970 351C-2V and 351C-4V with correct ink stamped Ford script, 17 1/2" long including the 90 degree bend. Connects PCV valve to carburetor spacer plate. Other parts houses list this as a 71-73 but the 71-72 is 25" long (so it can reach to the front of the driver side valve cover) on both the 2V and 4v 351 Cleveland and this hose will not reach. This will work for the 1973 Q-code 351C-4V as the 73 mates to a metal tube and is only 11".This hose was originally installed from the...

MSRP:$29.99
$29.99 Price: $19.31

Buy Details

Availability: In-Stock Item
Item #: 41969 -

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

$0 Price: $34.97

Buy Details

Availability: In-Stock Item
Item #: 14082 -

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose will work as a return line for either a small or big block 1967 - 1970. This hose is designed for a 2 piece return line application, so to make it work you will need to also purchase a chunk of generic hose. This is needed to connect this hose to your power steering pump.  Depending on the routing of your hoses you will need a different...

$0 Price: $17.27

Buy Details

Availability: In-Stock Item
Item #: 14079 -

Water By-Pass Hose for 351W engines with Autolite® logo and part number imprinted in white ink. Stamped with C9OE-8597-D. This would be correct for Mustangs and other Ford or Mercury with 302 engines in 1969. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

$0 Price: $31.65

Buy Details

Availability: In-Stock Item
Item #: 30773 -

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 10/22/69

$0 Price: $31.65

Buy Details

Availability: In-Stock Item
Item #: 30774 -

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 12/15/69

$0 Price: $31.65

Buy Details

Availability: In-Stock Item
Item #: 30775 -

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 2/12/70

$0 Price: $31.65

Buy Details

Availability: In-Stock Item
Item #: 30770 -

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 5/2/69

$0 Price: $31.65

Buy Details

Availability: In-Stock Item
Item #: 30771 -

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 6/6/69

$0 Price: $33.27

Buy Details

Availability: In-Stock Item
Item #: 30772 -

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 8/18/69

MSRP:$8.00
$8.00 Price: $7.35

Buy Details

Availability: In-Stock Item
Item #: 26605 -

The 1969 - 1970 windshield washer kit varies slightly from the 67-68.Replaces Ford part #: C9ZZ-17543.

$0 Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 12865 -

Reproduction 1/2" hose clamp, commonly used on the fuel lines. This clamp is smaller than the ones used on the power steering return line.