1970 Mercury Cougar

Hex bolt for attaching fuel line clips. 5/16-18 bolt. See related items for reproduction clips.

Reproduction 60000 Mile 6 Month Lube Sticker for the 1967 - 1973 Mercury Cougar / Ford Mustang

Reproduction 97 License Plate Light Bulb for the 1967 - 1973 Mercury Cougar

Reproduction inner "A" pillar panel and fresh air vent vent panel set for the driver side (left hand) of the Mercury Cougar or Ford Mustang. This item features weld through primer and is ready to install. Unfortunately both Cougars and Mustangs alike are prone to rust in these areas, so finding a nice original piece can be difficult. We're delighted to have this high quality panel set to offer you the perfect pieces to replace those rusty units you have now!

Reproduction inner "A" pillar and fresh air vent panel set for the passenger side (right hand) of the Mercury Cougar or Ford Mustang. This item features weld through primer and is ready to install. Unfortunately both Cougars and Mustangs alike are prone to rust in these areas, so finding a nice original piece can be difficult. We're delighted to have this high quality panel set to offer you the perfect pieces to replace those rusty units you have now!

Here is our A/C dryer decal for your Coug or Stang equipped with A/C. Replaces Ford part #: D0AA-19959-C3.

This replica tag is of a lower quality than the originals were. The aluminum stock from which this Mercury Cougar A/C tag is made, is about half the thickness of original and the font, instead of being white, is unpainted aluminum. This is a cheap looking, and feeling, part compared to the original. We do have the clip that holds it in place. Check out the product images for an example of factory placement for this tag.

Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version. 

Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Air conditioning fan blower assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

Reproduction A/C evaporator for the later production 1969 - 1970 Mercury Cougar and Ford Mustang. This later version of the evaporator has inlet and outlet tubes that run diagonally of the core as opposed to the early version where the tubes run horizontally.*Note - We have had numerous customers complain that these don't fit exactly like the originals. As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies...

Used air conditioning evaporator core, for most of the 1969 model year and all of 1970. You will need to make a comparison with your A/C box or old evaporator for selection. Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have...

Exact replacement to original dryer. Drier removes moisture and should be changed anytime system is recharged. It is the life of your system. Stainless steel filter element. Filter stops contaminants from clogging expansion valve. Replaces part # C9ZZ-19959-A.

This unit is a reproduction concours correct A/C discharge hose for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.

Regardless of which V-8 engine, C9ZA-19972-C or C9ZA-19972-E, both are the correct part number. This hose is approximately 20 inches long. Ford part # C9ZZ-19972-C.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine from 1969-73. Original condensation drain hose from the A/C case, through the floor board, to the ground. Replaces Ford part # C9ZZ-19858-C.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Ford part # C9ZZ-19858-C.

Regardless of which V-8 engine, C9ZA-19837-A or C9ZA-19837-C both are the correct part number. This hose is approximately 68 inches long. Ford part # C9AZ-19837-A.

Here is your concours correct A/C suction hose for your beloved Mercury Cougar or Ford Mustang.This hose is compatible with both 134a and R12 refrigerants.

A/C suction line for the evaporator to compressor for the 1970 Mercury Cougar or Ford Mustang with any V-8 engine. This hose is approximately 55 inches long.Ford part # D0ZA-19867-A and MPC # D0ZZ-19867-A.

For 1969-70 Mercury Cougars and Ford Mustangs with the 351W engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 6", and an overall thickness of 2-1/16 inches. Ford part # C9AA-2981-F.

For 1969 Mercury Cougars and Ford Mustangs with the 351W engine and also for 1970 Cougars and Mustangs with the 351W or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-3/16", and an overall thickness of 1-1/2 inches. Ford part # C9AA-2981-D1. May also have part # C9AA-2981-D2.

Reproduction A/C Tag Retainer for the 1967 - 1973 Mercury Cougar

Grade B A/C vacuum canister that has a non working check valve. Suitable for filling the hole in your passenger side fender apron. This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and not holding vacuum, tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's...

This A/C vacuum canister mounts to the passenger side fender well and controls doors inside the A/C unit. This unit includes a built in check valve. Fits 1968-1970 Mercury Cougar and Ford Mustang. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength.  Replaces Ford part # C8ZZ-19A566.

Complete vent includes mounting hardware. These are sold individually, so please choose between driver and passenger side. We do not guarantee the felt strip to be in place (see picture for example) and we do not guarantee good chrome finish on the louvers. We do inspect them carefully for cracks. Ford part # C9ZZ-19893-D driver side, C9ZZ-19893-C passenger side. *NOTE* The leading edges of the round plastic register are chromed. Often the chrome will wear off, but if you rotate the register...

Complete vent includes mounting hardware. These are sold individually, so please choose between passenger and driver side. We do not guarantee the felt strip to be in place (see picture for example) and we do not guarantee good chrome finish on the louvers. We do inspect them carefully for cracks. Ford part # C9ZZ-19893-C passenger side, C9ZZ-19893-D driver side. *NOTE* The leading edges of the round plastic register are chromed. Often the chrome will wear off, but if you rotate the register...

Reproduction pair of A/C vent registers for your 69 - 70 Cougar or Mustang. Sold as a pair. Replaces Ford part numbers: C9ZZ-19893-D driver side, C9ZZ-19893-C passenger side.

part # 370608-S. Used in multiple places on mounting brackets.

Reproduction diaphragm pump that mounts on the front all 67 - 73 Cougar or Mustang Autolite 2V carbs as well as 1967 Autolite 4V Carbs. With today's gas, these commonly fail, especially when sitting for extended periods of time. Complete failure will cause fuel leaks, but many times these will affect performance well before a leak actually starts. Good idea to replace every few years or if sitting for 6 months or more. Replaces Ford Part #: C4AZ-9B559-A.

Stainless insert that fits in holes around wheel.Fits the following models with styled steel wheels:1969 Mercury Cougar1970 Mercury CougarThese inserts fit or both the 1969-70 OEM Cougar styled steel wheels and the reproduction 1969-70 styled steel wheels. These are the most up to date version of these bezels. The originals tend to have a more mirrored finish like the stainless steel window trim, these reproductions tend to have a brushed nickel look to them.Sorry, these do not come with...

Set of 20 stainless inserts that fit in holes around wheel.Fits the following models with styled steel wheels: 1969 Mercury Cougar1970 Mercury Cougar These inserts fit or both the 1969-70 OEM Cougar styled steel wheels and the reproduction 1969-70 styled steel wheels. These are the most up to date version of these bezels. The originals tend to have a more mirrored finish like the stainless steel window trim, these reproductions tend to have a brushed nickel look to them.Sorry, these do not...

Polished stainless steel inserts that fit in holes around wheel.Fits the following models with style steel wheels:1969 Mercury Cougar1970 Mercury Cougar1969 Mercury Cyclone1970 Mercury CycloneNice used, in most cases we can supply the rubber gaskets, but not always.Limited to stock on hand. ...

Molded rubber plug, seals access hole in the side of shift housing. Replaces Ford Part # : C5ZZ-7C147-B Check out our video on rebuilding your shifter below: ...

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

C9ZZ-14A318-A-Used Wire lead for the accessory terminal found optionally on 1969-70 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire can be marked with C8OB-14A318-A or C9ZB-14A318-A.NOTE: There are two version of this wire, one is long and the other is short. The shorter version has a smaller gauge wire. ...

There are 3 of these acorn nuts used per emblem. They are taller than what was used in 1968.Sold individually.

Ford called this small door latch part an adjuster. It threads onto the bottom of the door latch rod inside the door. Common to most Ford products 1965-1970. Ford part number C5AZ-62218106-A.

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

Fits perfect! The collar that slips into the opening of the bell housing is very tight for a precise fit that will withstand high horse power motors.

Reproduction center cap adapter kit for installing Legendary center caps on the Legendary Series GT9 wheels. The spacing is a bit deeper on these specific wheels, so this adapter kit comes with special adapters and longer screws.  This kit is intended to make original and after market Mag 500 and Style Steel wheels center caps work on the Legendary Series GT9 wheels.  Please note that the included screws may not fit the thread pattern of some center caps.  The plates will...

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the black colored adhesive and is the 5 ounce size.

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the yellow colored adhesive, the factory used yellow adhesive on the weather stripping and is the 2 ounce size.

New 5oz tube of yellow weatherstrip adhesive for installing the rubber weatherstripping found on the Mercury or Ford. This 3M brand adhesive is a great match to the yellow colored adhesive that Ford used to attach the weatherstripping on many of it's vehicles back in the day.

Set of 8 fine threaded Phillips screw assemblies. This the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the...

This fine threaded Phillips screw assembly is the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The two new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the comparison...