1970 Mercury Cougar

Set of four NOS vinyl top mouldings. The vast majority of hardtops in 1969 and 1970 had painted mouldings, but on two tone painted cars and the 1970 "Hounds-tooth" edition, chromed mouldings were supposed to be included. However, we have found exceptions to the rule.NOTE: These mouldings will have some shelf wear, see photos above. If you have extra sets of cores, we would be willing to give in store credit. Ford casting numbers on backs:  Driver side C9WB-65423A19 Passenger side...

Set of four re-chromed vinyl top mouldings. The vast majority of hardtops in 1969 and 1970 had painted mouldings, but on two tone painted cars and the 1970 "Hounds-tooth" edition, chromed mouldings were supposed to be included. However, we have found exceptions to the rule. If you have extra sets of cores above and beyond the four needed to exchange, we would be willing to give in store credit. Restored moulding will not ship until we receive your cores. All mounting studs must be intact to be...

Good set of four die cast original top mouldings for both two tone paint Cougar hardtops and Cougars with a factory installed vinyl top. No broken studs, cracks, bends or chips. Originally these came painted and in rare cases like the 1970 Hounds-tooth edition or select two tone paint cars, those came chrome plated. These trim parts will need to be painted, Includes 15 new or used speed nuts for installation, just in case. This icon means that we're looking to buy this part!WCCC is a buyer of...

These trim parts (as with all our restored aluminum) feature the correct bright dip anodized plating, just as they came from the factory. If you have extra cores you would like to sell then we would like to hear from you! Please DO NOT send heavily damaged trim parts as the finished product will be delicately thin. Cores that are corroded, torn, smashed or kinked are not acceptable cores either.  Please, only send cores with small dings, scratches and dullness.  Extra screw holes and...

Set of 4 reproduction wheel lip mouldings for the 69-70 Cougar. These are spot on and we had no problem fitting them on our cars, the only difference we noticed is that the aluminum is softer than the originals and prone to dimpling. And since they're reproductions, no cores are required! Keep in mind that when you remove your rear core mouldings, you can send them to us as they might be eligible for in store credit. For more info on aluminum trim restoration & core exchanging, check out our...

Good set of four used wheel lip mouldings for your 1969 - 1970 Mercury Cougar. What is considered to be an "acceptable core" is solely at our discretion. If you are in question as to what good cores are, please send quality, in focus, close-up digital pictures to westcoast@classic-cougar.com *NOTE* Some "on the edge" cores that need extra labor can be given a partial credit.*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by WCCC....

This original FoMoCo, five piece windshield trim set has been lovingly restored to far beyond the original luster. Stunning brilliance, perfect match for that high end paint job. Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well.Ford part numbers include: C9ZZ-6503136-A, C9ZZ-6503137-A, C9ZZ-6503144-A, C9ZZ-6503148-B, and C9ZZ-6503149-B....

Because this windshield moulding set is comprised of used original pieces, it will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part numbers include: C9ZZ-6503136-A, C9ZZ-6503137-A, C9ZZ-6503144-A,...

Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. This original FoMoCo, six piece windshield trim set for the Mercury Cougar convertible has been lovingly restored far beyond the original luster. Stunning brilliance, perfect match for that high end paint job. Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option...

This original FoMoCo, six piece windshield trim set for the Mercury Cougar convertible. Because these pieces are original pieces, they will have far superior fit when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well. The four upper pieces are wider than the coupe versions, but the lowers are the same (with about an inch cut off the ends). The trim is... trimmed so it will fit underneath the pillar trim pieces. *NOTE* If your trim has...

Reproduction sway bar mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.

Original driver side sway bar mount for your LATE 1968-70 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions available in 1968. Both curved and straight cut, even on the same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, this is the driver side only. See related...

Reproduction sway bar clamp mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.

Original passenger side sway bar mount for your LATE 1968-70 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions available in 1968. Both curved and straight cut, even on the same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, this is the passenger side only....

According to the MPC 1970 primarily, a few 1971-1973's. If you have a hardtop or coupe, (VIN numbers starting with either 0F91 or 0F93) and standard wheels with hub caps. Or, any 1971 - 1973 with style steel wheels. Total length is 6-1/4 inches, with 4 inches being threaded. Threads 1/2-13. We find this bolt to only have 2 1/2" of threads. More data is needed as the MPC is not reliable on these items. What do you have in your trunk? We want to know! Search words 70 71 72 73 1972

Cast iron pedestal mount for the air conditioning compressor on all 1970 - 1973 Mercury Cougars and Ford Mustangs with the 351C engine, both the H code 351-2V and M code 351-4V engines. Ford MPC part # D0ZA-2882-C.

Air compressor mounting pedestal for 1969 and 1970 Mercury Cougars or Ford Mustangs with 390 or 428CJ engines. Casting number C9AA-2882-A.Ford part # C9AZ-2882-A.

Used alternator mounting bracket for any 1970-73 Mercury Cougar, Ford or Ford Mustang with 302, 351W, or 351C engines. Replaces Ford part number D0OE-10156-A.

Used rear alternator mounting bracket, attaches to the passenger side cylinder head. For any 1970 Mercury Cougar or Ford Mustang with 351W engine. Replaces Ford part number D0OE-10A336-A.

This used original Bendix spacer bracket is mounted to the rear of the brake booster on the 69 - 70 Cougar and Mustang. These spacer brackets sometimes come up missing when purchased from discount booster rebuilders. If you get a booster that has a piece of plate steel and spacers in place of this stamped steel bracket, it is a go around (homemade). This plate differs from repro in that the mounting holes are the correct size and it has the correct relief spacing for the input rod dust boot....

This reproduction Bendix spacer bracket is mounted to the rear of the brake booster on the 69 - 70 Cougar and Mustang. These spacer brackets sometimes come up missing from some booster rebuilders. If you get a booster that has a piece of plate steel and spacers in place of this stamped steel bracket it is a go around (homemade). This plate differs from original in that the holes are smaller than factory so they will need to be enlarged and there is no relief spacing for the input rod dust boot...

C8OZ-2B293-A Driver side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog.

C8OZ-2B292-A Passenger side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog.

D0WY-9A225-A "L" shaped mounting bracket for the rear evaporative vapor separator, mounts in the drivers side trunk well. *Note - This is only a small part of the 9B004 assembly.

This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.You can find our reproduction pair of brackets here. ...

These aluminum ninety degree brackets are what fastens the XR7 chrome boot moulding to the quarter panels. The beltline weatherstip also attaches to them. These parts are only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.

This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.You can find our reproduction pair of brackets here. ...

Metal stamped brackets used to mount the radiator on saddle mounts styles only. Rubber insulators not included.Check out our video on Radiator and Fan upgrades below:

When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is the way to go. Consider adding the upper rubber pieces to your order, see related items.These brackets came in two configurations, most has the round mounting holes but some were punched square. Not for use on...

Sometime during the 1970 model year, this bracket was used on cars with 24 inch radiators. At the beginning of the year the 1969 bracket was being used. Pretty much indistinguishable when mounted on the car. When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is...

These plastic mounting brackets came in black or gray. These kinds of minor differences can often be attributed to different suppliers. We have many that still retain the LH & RH decal for those of you trying to obtain a show car level in your restoration. The backside of this bezel will be marked LH - TOP.D0MB-15A470-B

These plastic mounting brackets came in black or gray. These kinds of minor differences can often be attributed to different suppliers. We have many that still retain the LH & RH decal for those of you trying to obtain a show car level in your restoration. The backside of this bezel will be marked RH - TOP.D0MB-15A432-B

Reproduction thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Painted Ford engine blue a shown. Nice reproduction, made in the USAFord part # C8AE-9C486-A.

Thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Ford part # C8AE-9C486-A. *RESTORATION TIP* This bracket was painted Ford Engine blue from the factory.

Used mounting bracket for the sunroof motor on the 67 - 70 Mercury Cougar. This bracket is only used with the 67 - 70 power sunroof motor.

Used bracket that mounts in the rear Carburetor mounting hole of all 1970 351 Cleveland 2 barrel engines. Has the square hole that holds the factory throttle cable. This bracket is identified by the hump or curve midway between the carburetor mounting studs.Replaces Ford part number D0OZ-9741-A.*Note - Not for use with 351 Windsor engines, or M code 351C-4V engines.

Bracket that mounts in the rear Carburetor mounting holes of all 1969 and 1970 351 Windsor 2 barrel or H code engines. Has the square hole that holds the factory throttle cable.Replaces Ford part number C9ZZ-9741-D.

Nice reproduction of the Boss 302 throttle bracket as found on the G code Boss2 cars. Includes 1969-70 Cougar Eliminator and Mustang. Similar to the 428 Cobra Jet bracket but with an extended spring tab.

Original FoMoCo used windshield wiper motor mounting bracket for your 1969-70 Mercury Cougar or Ford Mustang. This used bracket comes with grommets, for all 1969-70 Cougar and Mustangs. Mounts under the cowl cover at the windshield. Ford part # C9ZZ-17496-A.

Metal-stamped 1968 - 1970 Lower Radiator Mounting Brackets feature exact detail and proper fit. Painted dull black. Sold in Pairs. Rubber insulators not included. Replaces Ford part # C8ZZ-8052-A. Check out our video on Radiator and Fan upgrades below: ...

Our used lower cradle brackets for the 24" wide radiator will always have some amount of damage as shown. We will not send you mangled junk that is heavily rusted but they will require some amount of straightening due to their vulnerable location. These also work with the 67 small block and big block when putting in a 68-70 24" radiator but keep in mind the 1967 cars are not pre-drilled as are the 1968-1970 Mustang and Cougar.We are out of the 1970 style of brackets. We only have the two...

D0WY-9A188-A and D0WY-9A188-B Mounting bracket for the evaporative vapor separators, mounts in the drivers side trunk rail. Two brackets paired up. *Note - This is only a small part of the 9B004 assembly.

U-shaped bracket that mounts the long flat part of the front sway bar to the chassis. Clamps sold individually, two needed for attaching front sway bars. This clamp with the folded ears on the sides is for the 7/8 and 15/16 inch front sway bars.

Concours correct reproduction of the front sway bar clamps used on all 67 - 70 Cougars and Mustangs with the competition suspension option, or 15/16th" sway bar. Never available until now. Exactly like the originals in every detail. Standard for all Shelbys, Boss 302s, and Cobra Jets. Stamped and formed just like the originals.

Pair of U-shaped brackets that mounts the long flat part of the front sway bar to the chassis. Two needed for attaching front sway bars. *Note* 1969 and 1970 Cougars with the Competition Handling Package which included all with 428CJ and Boss 302 engine packages, used a different bracket with a Ford part number of C7ZZ-5486-A.Replaces Ford part number #: C6OZ-5486-B.

There is not a special part number for this angled cup that was originally spot welded to the front of the headlamp switch. We offer these for use with our reproduction headlamp switch. This adapter or retainer is needed to correctly keep the headlamp switch at the correct angle to the lower metal dash. 1969-70 Mercury Cougar.

Repro fuel pump gasket for 1967 - 1970 Cougars or Mustangs with 289/302/351W/390/428CJ engines.

Good used part cut from the trunk of a 69-73 Mercury Cougar. This hook is concealed under the trunk mat and suspends the sequential unit over the trunk drop off area on the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...